Converters.TV 15267 User manual

HDBaseT HDMI Over CAT
Cable Receiver w/ 5Play Convergence,
Scaler, For at Converter - # 15267
Operation Manual

Introduction
The HDMI video scaler with LAN/IR/RS-232/Bidirectional Po over Single
CAT5e/6/7 Receiver can receive uncompressed audio/video over a single
run of CAT5e/6/7 cable up to 100m or over HDMI input with Bidirectional
Po feature. The system supports various ways of control that can be done
through on-panel buttons, IR remote, RS-232 and OSD. The device provides
full range of output resolutions up to 1080p for HDTV timing and
WUXGA(RB) for PC timing.
.
Applications
• xtending incoming signal from CAT5e/6/7 to HDMI output
Scale up HDMI input low resolution video on High-Definition display
Lecture room/Showroom/Meeting room/Classroom display and
control
Syste
Require ents HDBaseT compatible Transmitter input or PS3/Blu-ray player and
output display with HDMI input jack
Features
• Supports full range HDTV and PC output resolutions up to 1080p
and WUXGA (RB)
Receive HDMI signal and scale up to HD output
Receive uncompressed data over a single 100 m/328 ft CAT5e/6/7
cable
5Play™ convergence: Video, Audio, LAN, Bidirectional Po &
Control (IR & RS-232 bypass)
Supports IR, Remote control, RS-232 (bypass) and on-panel
controls
Supports OSD (On Screen Display) selection and display system
information
Provide with 24V DC power to or received from compatible Po
Transmitter through CAT5e/6/7
Supports thernet transmission rate up to 100Mbps
Supports HDMI, Optical (S/PDIF) audio sampling rate up to 48kHz
Support HDMI and Optical (S/PDIF) audio up to LPCM 2CH
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a different specification.
2. The Po function is designed for powering compatible Transmitter
units only—non-Po Transmitter will need their own power supply.
Transmitters of another brand may not be compatible.

Operation Front Panel
Controls and
Functions
1. SERVICE:
This port is reserved for firmware update only.
2. IR:
IR Receiver window (accepts the remote control signal of this device only).
3. OPTICAL OUT:
Connect to an amplifier or active speaker with optical cable for audio
output.
4. HDMI OUT:
This slot is to connect with HDMI TV/Monitor
5. HDMI IN:
This slot is to connect with source equipment such as DVD/PS3 player.
6. MENU:
Press this button to enter into the OSD menu.
7. INPUTNT CAT/HDMI LED:
Press this button to select input from CAT or HDMI. When input CAT is
selected the L D will illuminate in green and when input HDMI is selected
the L D will illuminated in red.
8. -/+:
Press these buttons to scrolled down and up in the OSD selection.
9. ENTER:
Press this button to confirm the selection. Press this button together with
[–] key to switch output timing to 720p@60 instantly.
Press this button together with [+] key to switch output timing to XGA
(1024x768) instantly

Rear Panel
1. Power LED:
This L D will illuminate when the device is connected to a power supply.
2. DC 24V:
Plug the 24 V DC power supply into the unit and connect the adaptor to an
AC outlet. Only one side of power is needed to activate both Transmitter
and Receiver when both obtain the Po function.
3. RS-232 OUT:
This slot is to connect with D-Sub 9-pin cable from device equipment for
receiving RS-232 commands.
4. LAN:
Connect to an active network for LAN sharing of a total transmission rate
up to 100Mbps. Or when a compatible LAN equipped Transmitter is
connected to an active network, this allows the network access (including
internet access if available) to be shared between the Transmitter and
Receiver. Connect any thernet equipped device e.g. a Smart TV or
games console to the LAN port for that device to share the network
internet access.
Note:
DO NOT connect this slot with any of the CAT5e/6/7 port.
Doing so may trigger power shoot down and ruin the device.
5. IR B aster:
Connect to the supplied IR Blaster cable for IR signal transmission. Place
the IR Blaster in direct line-of-sight of the equipment to be controlled.
6. IR Extender:
Connect to the supplied IR Receiver cables for IR signal reception. nsure
that remote being used is within the direct line-of-sight of the IR xtender.
7. MODE LED:
This L D will illuminated when the power is connected.
8. Link LED:
This L D will illuminate when the slot has been connected to the
Transmitter and the Transmitter has connected with sources that shows
image on screen.
9. CAT5e/6 IN:
Connect to the Transmitter unit with a Single CAT5e/6/7 cable for
receiving all data signals

IR Cab e
PIN Assignment
RS-232 Protocols
CAT Cable Reciever
PIN Definition TX/RX
 
 
 
 
 
 
 
 
 
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1

RS-232 & Telnet
Co ands
Co and Description


1=HDMI
2=CAT IN
Reports the numerical equivalent for SOURC setting
(as above)


0=Native 12=1600×1200
1=640×480 13=1920×1080
2=800×600 16=1920×1200
3=1024×768 17=480p
5=1360×768 18=720p@60
6=1280×720 19=1080p@60
7=1280×800 20=1080i@60
8=1280×1024 22=576p
9=1440×900 23=720p@50
10=1400×1050 24=1080p@50
11=1680×1050 25=1080i@50
Reports the numerical equivalent for OUTPUT
setting (as above)


0=OV RSCAN 4=L TT R BOX
1=FULL 5=UND R 2
2=B ST FIT 6=UND R 1
3=PAN SCAN
Reports the numerical equivalent for SIZ
setting (as above)


Setups the numerical equivalent for
CONTRAST setting (as left)
Reports the numerical equivalent for
CONTRAST setting


Setups the numerical equivalent for
BRIGHTN SS setting (as left)
Reports the numerical equivalent for
BRIGHTN SS setting


Setups the numerical equivalent for HU
setting (as left)
Reports the numerical equivalent for HU
setting


Setups the numerical equivalent for
SATURATION setting (as left)
Reports the numerical equivalent for
SATURATION setting


Setups the numerical equivalent for
SHARPN SS setting (as left)
Reports the numerical equivalent for
SHARPN SS setting
 0=OFF 2=MIDDL
1=LOW 3=HIGH

 Reports the numerical equivalent for the
NOIS R DUCTION setting (as above)
 !
 !
0=OFF 2=110ms
1=40ms 3=150ms
Reports the numeric equivalent for AUDIO
D LAY setting (as above)
"
"
0=ON 1=MUT
Reports the numeric equivalent for AUDIO
MUT setting (as above)
#! #
#! #
0= NABL 1=DISABL
Reports the numeric equivalent for K Y
LOCK setting (as above)
FW Checks the FIRMWAR version
S R S T 1 Setups the numerical equivalent for R S T
setting (as left)
Note:
1.All the RS-232 command will be not executed unless followed with
carriage return and LF (Line Feed).
2. Commands are case-insensitive.
3. Resolution 1~16 are RGB encoded and 17~25 are YUV encoded.
4. Digital audio supports LPCM 2CH only, please ensure source
input audio is sending LPCM 2CH's audio signal in order to avoid
unnecessarily audio noise
Re ote Control
1. INPUT:
Select input source from
CAT or HDMI.
2. EXIT:
Press this button to exit the
menu or escape the current
selection under OSD.
3. MENU:
Press this button to enter
into the OSD menu.
4. RESET:
device back into the factory
default setting.
5. AUTO ADJUST:
This button will not
function under this model.
6. ENTER & ▲▼◄►:
Press nter to
confirm the selection or press the
arrow buttons to scrolled in the
OSD selections.

Connections

OSD Menu
1st Layer 2nd ayer 3rd Layer
$%&'() *+&*+ (+$,-
.












.
1280X720P 60
.
.
.
.
.
.
/'/*0 $1- ,-0%2(3
FULL
%&-2+(+$/
(3%2(3
-++-0/
34-0
34-0
"/4-35/ INFO

3
55
/'/*0 


55%-+
55%-+
55%-+
/3+0(%+ 
0$67+3-%% 
*- 
(+*0(+$/3 
7(0&3-%% 
8 99
/:
"$44'-
$67
*4$/ -'() OFF
;
;
;
/*34 ON
"*+-
-+*& 9(2+/0)-%-+ No
!-%
#-) /2< Off
3
35/0;(+$/3 3&*+
*+&*+
-,$%$/3

Output Resolution
Support
Input Resolution HDMI
$$ !
&& !
&=1 !
$=1 !
&=1 !
>=1 !
>=1 !
.=1 !
.=1 !
.=1 !
?=1 !
?=1 !
?=1 !

Specifications
Ethernet Speed "@&%
Input Video Bandwidth "18@&%
Output Video bandwidth "18@&%
Input Ports -A+-34-0A
"
Output Ports "A?'(%+-0A
&+$2('ABA? 
CAT5e/6/7 Output Cable Distance &+/"-+-0%
HDMI output Resolution C&+/&=1
C&+/D.EF
Audio Sa pling Rate &+/<1 "
CAT5e/6/7 Output Resolution C&+/&=1
C&+/D.EF
IR Frequency <1
ESD Protection *;(3@/4);/4-'C
G<>E($0B6(&4$%27(06-F
G<>E2/3+(2+4$%27(06-F
Di ensions ( ) EDFEFEFH(2<%
2'*4-4
EDF8EFEFH(2<%
32'*4-4
Weight (g) 
Chassis Material '*;$3*;
Silkscreen Color '(2<
Operating Te perature IJKLMNIJKLJOJPQJKRMSINJKR
Storage Te perature TQIJKLJMJUIJKLJOJTNJKRJMJSNIJKR
Relative Hu idity VE3/3B2/34-3%$36F
Power Consu ption D