Converters.TV CAR-1 Installation manual

Video to RGB/Sync
Converter
Operation Manual

Features:
1. Digital decoding and encoding ensures best conversion quality.
2. Converts NTSC/PAL /SECAM composite video to RGB/Sync
or RGSB(Sync on Green).
3. Input system auto detecting.
4. RGBS input loop through.
5. Sync polarity switchable between positive and negative.
6. Output brightness adjustable.
Operation Controls and Functions:
RGB OUT
RGSB
RGBS RESET
-
+
BRIGHTNESS
Front Panel
1. + and - Buttons: Use these two buttons to increase or decrease the brightness.
Reset: Simultaneously depressing the + and - buttons return brightness to
factory default.
2. RGBs/RGsB Switch: To select between RGsB(sync on Green)or RGBs.
3. 9-Pin D Females connector:
DB9 Pin configuration
PIN 1 GND
PIN 2 Sync of source 1
PIN 3 RED out
PIN 4 RED in from source 1
PIN 5 Green in from source 1
PIN 6 Green out
PIN 7 Blue out
PIN 8 Blue in from source 1
PIN 9 Sync out
Source 1: Loop-through RGB/S input.
Source 2: Video input.
Gray:
Brown:
Red:
Yellow:
Green:
Blue:
Purple:
Orange:
Black:
3
5
21
RGB out:
Bypass : short
Convert : open
Toggle Switch
Output Select
Open Convert
Short Bypass
JP2
4. Toggle switch to switch between convert and RGB bypass.
Red
Black
12V
(Camera)
0V
4
Blue
White

Operation Controls and Functions:
VIDEO INPUT DC 12V
Rear Panel
1. DC power supply input:
DC 12V center positive.
2. Video Input.
Specifications:
Input:
Video input: 1 Vp-p 75 ohm RCA jack x 1
RGBs input: Pass through
Output:
RGB: 0.7 Vp-p 75 ohm 9-pin D Females connector.
Sync: 3 Vp-p positive or Negative polarity
Power Supply: DC 12V center positive
Dimensions: 94mm(D)x77mm(W)x30(H)mm
Accessory: One set of D-Sub 9-pin RGB bare wire
and One set of 2-wire power cable.
Weight: 0.4 Kgs
21
When the control wire is connected to 12 Volt, it forces the unit to go into
convert mode. When the control wire has no voltage apply to it, the toggle
switch will dictate the convert/bypass mode.
C.wire
Output
T.Switch
Convert
Bypass
12V 0V
V in
V in
RGB Bypass
V in
5. Control wires(12V Camera/GND)

MPM-CAR1
Features:
1. Digital decoding and encoding ensures best conversion quality.
2. Converts NTSC/PAL /SECAM composite video to RGB/Sync
or RGSB(Sync on Green).
3. Input system auto detecting.
4. RGBS input loop through.
5. Sync polarity switchable between positive and negative.
6. Output brightness adjustable.
Operation Controls and Functions:
Operation Controls and Functions:
VIDEO INPUT DC 12V
RGB OUT
RGSB
RGBS RESET
-
+
BRIGHTNESS
Front Panel
Rear Panel
1. DC power supply input:
DC 12V center positive.
2. Video Input.
1. + and - Buttons: Use these two buttons to increase or decrease the brightness.
Reset: Simultaneously depressing the + and - buttons return brightness to
factory default.
2. RGBs/RGsB Switch: To select between RGsB(sync on Green)or RGBs.
3. 9-Pin D Females connector:
DB9 Pin configuration
PIN 1 GND
PIN 2 Sync of source 1
PIN 3 RED out
PIN 4 RED in from source 1
PIN 5 Green in from source 1
PIN 6 Green out
PIN 7 Blue out
PIN 8 Blue in from source 1
PIN 9 Sync out
Source 1: Loop-through RGB/S input.
Source 2: Video input.
Gray:
Brown:
Red:
Yellow:
Green:
Blue:
Purple:
Orange:
Black:
Specifications:
Input:
Video input: 1 Vp-p 75 ohm RCA jack x 1
RGBs input: Pass through
Output:
RGB: 0.7 Vp-p 75 ohm 9-pin D Females connector.
Sync: 3 Vp-p positive or Negative polarity
Power Supply: DC 12V center positive
Dimensions: 94mm(D)x77mm(W)x30(H)mm
Accessory: One set of D-Sub 9-pin RGB bare wire
and One set of 2-wire power cable.
Weight: 0.4 Kgs
3
5
21
21
RGB out:
Bypass : short
Convert : open
Toggle Switch
Output Select
Open Convert
Short Bypass
JP2
4. Toggle switch to switch between convert and RGB bypass.
Red
Black
12V
(Camera)
0V
4
When the control wire is connected to 12 Volt, it forces the unit to go into
convert mode. When the control wire has no voltage apply to it, the toggle
switch will dictate the convert/bypass mode.
C.wire
Output
T.Switch
Convert
Bypass
12V 0V
V in
V in
RGB Bypass
V in
Blue
White
5. Control wires(12V Camera/GND)