Converters.TV 796 User manual

Video to DVI 1080p Scaler Box
- ID# 796
Operation Manual

Introduction
Video to DVI 1080p Scaler Box is an upgraded design to convert Standard Definition
Composite Video (CV) and S-Video (SV) signals to igh Definition PC and DTV
resolutions. Maximum output resolutions available are WUXGA and 1080p. With
support for NTSC and PAL video format input, an in-built frame rate conversion
feature from 50 z to 60 z ensures glitch-free viewing. The Video to DVI 1080p Scaler
Box has many enhanced features to maximize video performance and is ideal for use
in professional large screen presentations or private home theater applications.
The Video to DVI 1080p Scaler Box DVI output is DVI-I (Integrated). This means that
the output supports both Digital and Analog screens. The link can carry single or dual
link all digital video/data signals on 24 pins, or Analog video/data signals and ground
on 5 pins. This makes the Video to DVI 1080p Scaler Box ideal for use with any
digital/analog video system.
Features
1. Motion adaptive 3D Y/C separation comb filter
( for composite video input )
2. 3D( frame Based ) motion adaptive YNR/CNR noise reduction
( for Y/C video input )
3. Advanced 3D motion adaptive deinterlace
4. Automatic 2：2/3：2 film mode detection
5. upports 50Hz to 60Hz frame rate conversion
6. Video quality improvement：
DCTI (Digital chroma transient improvement), DLTI (Digital luminance
transient improvement),
Black level extension.
7. Average picture level ( APL ), Automatic contrast limiter ( ACL ) function
supported.
8. O D menu for picture quality adjustment.
9. Built-in 8-bit DAC for RGB or YPbPr output.
10. Front Panel and IR remote control.
11. Automatic NT C/PAL video format detection and switching.
Operation
Controls and
Functions
Front Panel
1. Power button and LED indicator:
Press the button once to power on the unit, Press again to power off.
when the unit is powered on, one of the input LEDs will illuminate
depending on your last selection of input source before power off.
The factory default setting for the input is CV (composite video).

The green LED illuminates when composite video is selected.
The Yellow LED illuminates when -Video is selected.
2. Input select button:
Press the button to select your desired input source between composite
video and - Video.
3. IR Sensor: Infrared remote control sensor.
4. Menu/Enter: This button serves two purposes.
a. Press the button to bring up O D main control menu as shown in the
"O D Operation".
b. To act as a "enter" key to enter sub menu of you selected item or adjust
value of the selected item.
/6. +/- button: Press the button to move up or down the tick "V" to your
desired parameter. Or after a parameter is selected by pressing
MENU/ENTER button,
press the button to alter the value of your selected parameter.
Rear Panel
1. DC power jack: 5V 2A DC power input.
2. Composite Video: Use a Composite video cable to connect the
composite video output of the source equipment to this composite
video(CV) input of the scaler.
3. S-Video: Use a -Video cable to connect the -Video output of the
source video equipment to this " -Video" input on the back of the video
scaler.
-Video provides improved performance over composite video and is
recommended over composite.
4. DVI output: The Video to DVI caler Box can output a variety of PC and
HDTV progressive resolutions, in both digital and analog format through DVI-
I connector.
Digital output: Connect Video to DVI caler Box's digital DVI output to the
DVI input of your TV/display unit using a DVI to DVI cable .
Analog output: If you are to use Video to DVI caler Box's analog output to
connect to the analog input of your PC or HDTV, you need to use a DVI to
VGA adaptor to pull out analog signal from the DVI-I connector . The DVI to
VGA adaptor is then connect to the VGA input of your display monitor
through a VGA cable if output is PC resolution, or connect to the YPbPr
input of your HDTV through a VGA to YPbPr/3 RCA adaptor cable if output
is HDTV resolution.
Note: DVI to VGA adaptor is not included in the standard package,
and has to order separately.

Output Format
a. The format of digital DVI output is digital RGB
for all resolutions.
. The format for analog PC output is RGB and for
analog HD output is YP Pr.
OSD Operation
After power on the unit , press the menu button to bring up the main menu
page as below:
Main Menu
Picture adj.
V Output Setup
Exit
Use +,- button to move "V" to your desired parameter, then press
MENU/ENTER
to enter into sub-menu of your selected parameter.
Picture Adjust
When Picture Adjust is selected a sub menu as below comes up.
Default Range
Bright 16 1-31
VContrast 16 1-31
Color 16 1-31
Tint 16 1-31
Sharp 0 1-19
Default OK
Exit
USE +,- to move the tick (V) to yo r desired adj st item, Press the
Men /Enter to confirm yo r selection.

At this point, the selected parameter will turn red, and you can use +,- to
increase or decrease the value of the parameter.
When adjustment is complete, Press "Menu" to leave the parameter. Move
the tick "V" to "Exit", then press menu/enter to exit.
Output Setup
When Output et up is selected a submenu as below appears:
Output Setup
V Timing XGA
Exit
Press the " MENU/ENTER" button to enter into output timing select mode.
Press +,- to toggle through a variety of output resolutions as below.
Once your desired resolution is selected. press the menu/enter
to enter the resolution.
Note: 1. All output resolutions except 576p have 60Hz vertical rate,
The 576p resolution has 50Hz vertical rate.
DVI-I Pin
Configuration
DVI-Integrated(DVI-I): Supports both analog and digital connections to
the display.
This 29-pin connector can carry single or dual-link all-digital video/data
signals on 24 pins and uses 5 pins to carry analog video/data signals and
ground.

Remote Control
1. Display: Press the button to display input
source and output resolution on the screen.
2. Power: Power ON/OFF button.
3. VGA~1080p: Press to select your desired
output resolution.
4. Picture: Press the button to enter picture
adjust submenu. Use +,- button to move
cursor (V) up/down to your desired
parameter, press "Picture" again to
confirm.
. +/-: Press to move up/down the cursor (V)
to your desired parameter,or press to
increase/decrease the setting value.
6. Reset: Press to reset all setting back to
factory default value.
7. Exit: To exit O D.
8. Video: Press the button to select
composite video input.
9. SVideo: Press the button to select
Video input.

Specifications
Output Signal Specifications
Connection and installation
a. Digital Out: Connect to your TV through digital DVI interface
b. Analog Out: Connect to your TV through VGA or component interface
in case your TV has no DVI input