Converters.TV CPT-360 User manual

VGA to NTSC/Pal Video
Converter/
(CPT-360)
Operation Manual
Please browse our online catalogue to view our full product range.
44-48 Maitland Road, Mayfield East, NS , 2304 Australia, [email protected]
Phone [phone] Fax [phone]
www.converters.tv

Introdu tion
This unit allows information from your computer (VGA) to be viewed on a TV in either
PAL or NTSC. It converts three most often used PC modes- 1024 x 768, 800 x 600, 640
x 480 into NTSC and PAL with a touch of the remote control.
Pre autions
1. Do not expose this product to direct sunlight.
2. Keep the unit away from radiator, heat sources and magnetic field.
3. Do not place it in very dusty or humid locations.
4. Use this unit in a horizontal position only.
5. Do not put heavy objects on top of the converter.
6. Put the unit in an open space that has good ventilation.
7. If the unit is acting abnormally keep the unit away from TV or other electronic
equipment.
8. Unplug the unit from the power supply when it is not to be used for a long period
of time.
Features
•Plug-and-play design, no software drivers required.
•Cross-platform compatibility for PC, Macintosh and Notebook.
•3 levels of brightness control plus 8 levels of sharpness control.
•Traditional Zoom & Pan.
•2X Zoom for one specific area.
•Screen freeze/unfreeze.
•Vertical and horizontal over-scan/under-scan control.
•Simultaneous display on PC and TV monitor.
•Composite, S-Video (S-VHS or Hi-8) and RGB output.
•Video output available in NTSC and PAL.
•Automatically supports scan rate from 50 Hz up to 100Hz.
•Selective high clarity 5-line anti-flicker filter.
•Built-in colour bar generator.
Please browse our online catalogue to view our full product range.
44-48 Maitland Road, Mayfield East, NS , 2304 Australia, [email protected]
Phone [phone] Fax [phone]
www.converters.tv

Operation ontrols and fun tions
Front Panel
1. Stand-by indi ator- The indicator will light up when in stand-by mode.
2. ON indi ator- This indicator will light up when in power ON mode.
3. Power button- Push this button in order to turn the power ON, or release to
switch the power off.
4. Zoom button- Push the button to zoom the picture.
5. Over-s an button- Push the button to over-scan/under-scan the picture.
6. Button- Push this button in order to pan the picture left.
7. Button- Push this button in order to pan the picture right.
8. Button- Push this button in order to pan the picture down.
9. Button- Push this button in order to pan the picture up.
10. Remote ontrol sensor.
Remote Control fun tions:
1. Reset button-Reset the Screen.
2. Over-s an button-Over-scan and under-scan control.
3. Power button-Power ON/OFF.
4. Bright button-Adjust the brightness.
5. Sharp button-Adjust the sharpness.
6. Col/BW button-Show the picture colour or B/ .
7. Freeze button-Freeze/Unfreeze the picture.
8. Colour bar button- Show the built-in colour bar.
9. Zoom for spe ial area- This button allows you to zoom IN/OUT of a special
area.
10. Zoom button-Zoom ON/OFF control.
11. Pan the pi ture, up, down, left or right.
Please browse our online catalogue to view our full product range.
44-48 Maitland Road, Mayfield East, NS , 2304 Australia, [email protected]
Phone [phone] Fax [phone]
www.converters.tv

Rear panel
1. DC Power supply input- This is the power supply input port. Connect the power
supply to the port.
2. VGA In- This is the VGA input port. Using the appropriate connector cable,
connect the VGA In to your input device.
3. VGA Out- This is the VGA output port. Using the appropriate connector cable,
connect the VGA Out to your output device.
4. RGB Out- This is the RGB output port. Connect the RGB output port to the RGB
output device using the appropriate connector cable (optional).
5. Sele t Video/S-out or RGB out individually- Either switch the button to VS
output or RGB output, thus you will individually select one or the other.
6. V-out- This is the Video output port. Using the appropriate connector cable,
connect the V-Out to your video output device.
7. S-out- This is the S-Video output port. Using the appropriate connector cable,
connect the S-Video Out to your S-Video output device.
8. Sele t NTSC or PAL Out- Switch the button to the output signal desired, either
PAL or NTSC.
Conne tion and Installation
The AC adaptor power unit should not be plugged into a wall outlet until all connections
are complete.
-The VGA Input port (Number 2 on the rear panel) connects the converter to a VGA
device, generally a computer.
-The VGA output port (Number 3 on rear panel) connects the converter to a computer
monitor.
-A Female connector cable is required to output VGA, whereas a Male connector
cable is required to input VGA.
-The RGB output port (Number 4 on the rear panel) connects the converter to a device
that accepts scart.
-Connect your video recorder or TV output devices to either the Composite Video
output port or the S-Video output port (Number 6 or 7 on rear panel), where your
output signal will either be PAL or NTSC.
-Switch the NTSC/PAL Out button to the signal desired, either PAL or NTSC.
- NOTE- Sele t Video/S-Video Out or RGB Out individually.
Please browse our online catalogue to view our full product range.
44-48 Maitland Road, Mayfield East, NS , 2304 Australia, [email protected]
Phone [phone] Fax [phone]
www.converters.tv

Once all connections are complete please connect the power supply provided to the
power socket
Spe ifi ations
Input signal VGA, Macintosh, Notebook.
Horizontal frequency- 24KHz~48KHz.
Vertical frequency- 50 Hz~100Hz.
Output signal Composite Video, S-Video, RGB (In NTSC
or PAL- switchable), loop-through VGA
output.
Power supply DC 6V 1A Center negative
A essory Remote Controller.
Dimension 192 (D) x 140 ( ) x 37 (H) mm
Weight 800 grams
Please browse our online catalogue to view our full product range.
44-48 Maitland Road, Mayfield East, NS , 2304 Australia, [email protected]
Phone [phone] Fax [phone]
www.converters.tv