Converters.TV CM-347 Installation manual

Video to PC/HD and DVI
Scaler Box ID# 141
Operation Manual

Introduction
The unit is a high performance video scaler that accept Composite Video,
S-Video, YCbCr component and RGB interlaced input and scales up to
high resolution PC or DTV output.
Features
• Output is digital RGB bit-stream via DVI connector.
• Selectable output refresh rate up to 85 z.
• Input clock and phase adjustment ensures noise-free output
picture.
• Video inputs are 3D de-interlaced and scaled up to PC or DTV
output resolution.
• Automatically accommodates worldwide input video systems of
NTSC3.58, NTSC4.43, PAL, PAL M, PAL N and SECAM.
• igh performance adaptive digital 4 Comb filter Y/C separator
with adjustable vertical peaking.
• Motion compensated de-interlacing algorithms to produce artifact-
free progressive scan video signal.
• Built in adaptive film mode 3:2 / 2:2 pull-down provides clear and
crisp deinterlacing of video originating from 24 fps film, such as
DVD movies.
• Vertical temporal filter (VT) removes jaggy and other de-
interlacing artifacts from normal video.
• OSD menu with adjustable control on Color, Sharpness,
Brightness, Contrast and Tint (NTSC).
• Last memory for all adjustments.
Operating Functions
and Controls
Front Panel

1. DVI Out This is the DVI Output port. Connect the port to your device
using the DVI digital cable.
2. The Menu button- This brings up the menu and it is used as a
enter/select button for menu options.
3. The – button- This is used to scroll through options or to adjust
selected options.
4. The + button- This is used to scroll through options or to adjust
selected options.
It also doubles as the input button, which is used to cycle through inputs
such as
Composite, S-Video, YCbCr and RGBs.
Rear Panel
1. YCbCr RGB IN this is a component input for component out devices.
For this port the connectors included are:
- 8 PIN Din Connector to 3 x RCA which are colour coded
for red, blue, green inputs. You may also insert into these
pins your RGBs (RGB sync on green device).
2. SV IN- this is the S-Video IN, which is for 5 Pin S-Video cable.
This connector is not included in kit.
3. CV IN- this is composite video for use with AV/RCA devices.
For this port the connector included:
- A single RCA cord.
4. Power- DC 5V - to be used with the power pack supplied, this power
pack will accept all country voltages, please however make sure you use
the right adapter plug to suit your wall socket.
1. Please note this device only alters the video signal, the audio
signal, goes directly from your output device to your input
device.
2. Video quality may alter depending on a number of factors:

- Quality of input source (the better you put in the better your going
to get out).
- Input connector used, e.g. Component and S-Video produce better
quality video
signal as opposed to composite video.
- Quality of cables used- Gold plated cables will produce a better quality
picture
then standard cables.
Menu Options
Picture Adjustment
· Brightness
· Contrast
· Colour
· Tint
· . peaking filter: Broad/Medium/Low.
· Sharpness
· V. peaking gains
· Reset
· Exit
Display Setup
· Timing
· CSC : RGB V, YPbPr
· Exit
Advanced
· Film mode- auto/off
· OSD Display- On/Off
· No signal- Blue/Black
· Exit
System Information
· Input Mode
· Display timing
· Exit
Trouble Shooting
Please note that changing some settings via the menu may cause the
picture to deteriorate or disappear altogether. Please don’t panic, this is not
a fault of the converter it is merely outputting a signal your output device
cannot accept.
To fix this problem:-
- For a PC monitor/VGA device press and hold the + and –
simultaneously, keys 3 and 4 on the front of the panel for 5 seconds and
release. This will reset the device to XGA mode that should be able to be
received by all VGA devices.
- For a DTV device press and hold the menu and – buttons
simultaneously, keys 2 and 3 on the front of the panel. This will reset the
device to a resolution of 480p, which can be received by all DTV
devices.

- If this does not work please power off the unit, wait 1 minute, turn the
unit back on and repeat the procedure. If you are still having problems
please contact [email protected].
Installation
The DC adaptor power unit should not be plugged into a wall outlet until
all connections are complete.
- Connect the output (Number 1 on front panel) to your output device.
You should have a blank blue screen. Pressing the menu button should
bring up the menu. This tells you that the device is operating correctly.
- There are a number of different inputs, choose the best input for your
input device.
With your input device connected, press the input button to cycle through
the inputs until you find the correct picture.
- Once all connections are complete please connect the power supply
provided to the power socket (Number 4 on the rear panel).
- Once power has been turned on, the LED light to the right of the socket
should light up, if this does not happen please check if it is connected
correctly.
Specifications