Cooper Lighting Portfolio LD4A User manual

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]
INSTALLATION INSTRUCTIONS
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE
LD4A/LD6A Emergency
Commercial Recessed Installation
Instructions
706084INS 4/04/13 page 1
PORTFOLIO®
ADP132108
STEP 1: To prevent electrical shock and unintentional battery
discharge, do not join the unit connector until the
installation is complete. Immediately prior to
permanently turning the A.C. power on, engage
the connector on the battery pack assembly.
STEP 2: This xture provides more than one power supply
output source. To reduce the risk of electrical shock,
disconnect both normal and emergency sources
by turning off the A.C. branch circuit and by
disconnecting the connector on the battery pack
assembly.
STEP 3: The emergency source requires an unswitched A.C.
power source of either 120 or 277 volts. Properly cap
the unused A.C. lead (Refer to wiring diagram).
STEP 4: This unit is for recessed ceiling mounting only. Do not
use outdoors, in hazardous locations, or near gas or
electric heaters.
STEP 5: This is a recessed ceiling mounted LED unit with
standby batter operation. In normal mode the LED
will be fully illuminated. In the emergency mode the
LED will provide emergency illumination for a minimum
of 90 minutes in accordance with the UL 924
standard.
STEP 6: The test switch and indicator light may be provided
for ceiling mounting near the xture in a single gang
switch box (Figure 1) or mounted on the housing in
an adjustable bracket to position directly in a
reector (Figure 2).
STEP 7: When used in insulated ceilings, insulation must be
kept off of the unit and no closer than 3” from the
unit on all sides.
STEP 8: Do not use this equipment for other than the
intended use.
STEP 9: Install only in accordance with National Electric Code
and local regulatory agencies requirements.
STEP 10: Installation and servicing to be performed only by
qualied personnel.
Risk Of Electrical Shock
Disconnect power at fuse
or circuit breaker before
installing or servicing.
WARNING
!
Risk Of Fire
Do not install insulation
within 3 inches (76 mm) of
any part of the luminaire
xture or in a way that
may entrap heat.
WARNING
!
Figure 1
Installation:
Figure 2
Servicing:

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]
INSTALLATION INSTRUCTIONS
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE
LD4A/LD6A Emergency
Commercial Recessed Installation
Instructions
706084INS 4/04/13 page 2
PORTFOLIO®
ADP132108
Electrical Wiring Diagrams
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
WHITE (INPUT)
0-10V DIMMING OPTION
(FIELD INSTALLATION)
GROUND
RED (+)
BLACK (-)
GRAY
PURPLE
BLACK (INPUT)
TRAILING EDGE
DIMMING OR
0-10V DIMMING DRIVER
CONNECTOR
WHITE JUMPER WIRE
(COMMON)
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
WHITE (INPUT)
0-10V DIMMING OPTION
(FIELD INSTALLATION)
GROUND
RED (+)
BLUE (-)
GRAY
PURPLE
BLACK (INPUT)
TRIAC DIMMING @
120VAC OR 0-10V
@120-277VAC
DIMMING DRIVER
CONNECTOR
WHITE JUMPER WIRE
(COMMON)
D010TE EMBOD (SEE WEBSITE FOR AVAILABILITY)
D010TR EMBOD (SEE WEBSITE FOR AVAILABILITY)

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]
INSTALLATION INSTRUCTIONS
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE
LD4A/LD6A Emergency
Commercial Recessed Installation
Instructions
706084INS 4/04/13 page 3
PORTFOLIO®
ADP132108
Electrical Wiring Diagrams
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
GROUND
3 WIRE
DIMMING
(FIELD
INSTALLATION)
ORANGE
WHITE JUMPER WIRE
(COMMON)
CONNECTOR
LUTRON DRIVER
(120-277V)
BLACK (INPUT)
PURPLE
PURPLE
BLUE (-)
RED (+)
LUTRON
ECOSYSTEM
DIGITAL
CONTROL
DIMMING
(FIELD
INSTALLATION)
WHITE (INPUT)
GREEN WIRE
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
GROUND
GREEN WIRE
WHITE (INPUT)
RED (+)
BLUE (-)
BLACK (INPUT)
LUTRON DRIVER
(120V)
CONNECTOR
WHITE JUMPER WIRE
(COMMON)
DL3 EMBOD (SEE WEBSITE FOR AVAILABILITY)
DLT EMBOD (SEE WEBSITE FOR AVAILABILITY)

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]
INSTALLATION INSTRUCTIONS
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE
LD4A/LD6A Emergency
Commercial Recessed Installation
Instructions
706084INS 4/04/13 page 4
PORTFOLIO®
ADP132108
Electrical Wiring Diagrams
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
BLUE~
BROWN~
-
+
GROUP 1
DA
-
+
GREEN WIRE
WHITE (INPUT)
DIMMING LEADS
(FIELD INSTALLATION)
RED (+)
BLACK (-)
PURPLE
PURPLE
BLACK (INPUT)
DRIVER
(120-277V)
CONNECTOR
WHITE JUMPER WIRE
(COMMON)
GROUND
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
RED (+)
GROUND
WHITE JUMPER WIRE
(COMMON)
CONNECTOR
DRIVER
(120-277V)
BLACK (INPUT)
PURPLE
GREY
BLACK (-)
DIMMING LEADS
(FIELD INSTALLATION)
WHITE (INPUT)
GREEN WIRE
+
-
0-10V
GROUP 1
+
-
BROWN~
BLUE~
DL5T EMBOD (SEE WEBSITE FOR AVAILABILITY)
DE010 EMBOD (SEE WEBSITE FOR AVAILABILITY)

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]
INSTALLATION INSTRUCTIONS
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE
LD4A/LD6A Emergency
Commercial Recessed Installation
Instructions
706084INS 4/04/13 page 5
PORTFOLIO®
ADP132108
Electrical Wiring Diagrams
MODULE WIRING
DIAGRAM
CONNECTOR
LED
RED (+)
BLACK (-)
ORANGE/BLACK (UNSWITCHED HOT)
BLACK
BLACK
VIOLET
BROWN
FLEX B
FLEX A
ITS
CONVERTER
CONNECTOR
RED
WHITE
BROWN (-)
VIOLET (+)
ORANGE/BLACK
BLACK 120V
OR
ORANGE 277V
(CAP UNUSED LEAD)
YELLOW
YELLOW/BLACK
BLUE
WHITE/BLACK
WHITE
WHITE/RED (SWITCHED HOT)
BODINE EMERGENCY BATTERY PACK
BLACK (-)
DMX in shield
BROWN
BLUE~
BROWN~
DMX in -
DMX in +
GROUP 1
-
+
GREEN WIRE
WHITE (INPUT)
DIMMING LEADS
(FIELD INSTALLATION)
ORANGE
YELLOW
BLACK (INPUT)
DRIVER
(120-277V)
CONNECTOR
WHITE JUMPER WIRE
(COMMON)
GROUND
RED (+)
DMX EMBOD (SEE WEBSITE FOR AVAILABILITY)