Cooper Lighting Sure-Lites LEM User manual

SURE-LITES LEM
page 1
Installation Instructions for the Sure-Lites LEM Emergency Light
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE OBSERVED INCLUDING THE FOLLOWING
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. 2. Do not use outdoors.
3. Do not use in hazardous locations, or near gas or electric heaters.
4. Do not let power supply cords touch hot surfaces.
5. Do not use this equipment for other than the intended use.
6. Installation is to be performed only by qualified personnel.
7. Install in accordance with National Electric Code and local regulatory agency requirements.
8. The use of accessory equipment not recommended by the manufacturer may cause an
unsafe condition.
9. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
10. SAVE THESE INSTRUCTIONS
INSTALLATION
Step 1 De-energize the circuit at the junction box (J-box) where the emergency light is to be installed.
Step 2 Open the emergency light by inserting a screwdriver in the two slots at the bottom of the unit, then
tipping the cover up off of the backplate.
Step 3 To mount to a junction box - Drill out the appropriate mounting pattern and the wire pass hole in
the backplate to fit the J-box being used.
Step 4 To mount to conduit – Cut out the U shaped knockout on the cover using snips, then attach the
½” conduit hub to the backplate
Step 5 Once the backplate is secured, the housing can be held in place during installation using the EZ
Hang feature. (see Fig. 1)
Step 6 Connect the incoming wires to the LEM power supply wires using the wire nuts provided.
Connect the white wire to neutral. If using 120V, connect the black wire to the hot lead. If using
277V, connect the orange wire to the hot lead. Cap the unused lead. Secure the emergency light
to the wall and/or junction box using installer supplied hardware.
Step 7 Snap the cover onto the backplate.
Step 8 Remove the EZ key battery disconnect.
Step 9 Energize AC supply. The test button should illuminate, and LED heads will illuminate briefly when
the test button is pushed.
Step 10 Adjust the heads as needed. The LEM heads utilize a highly directional beam, so the head is
adjustable in 3 axes, not the usual 2. (see Fig. 2)
Step 11 If the LEM is to be powered down for an extended period after initial installation, replace the EZ Key. This will prevent the battery from discharging
when AC power is removed. However, it will also prevent the battery from charging when AC power is restored, so it must be removed once the
unit is ready for regular operation.
Risk of Electric Shock
Disconnect power at fuse
or circuit breaker before
installing or servicing.
Risk of Fire/Electric
Shock
If not qualified, consult an
electrician.
Figure 1
Figure 2
Slide snaps
through holes
in housing for
temporary mount
when wiring

SURE-LITES LEM
page 2
OPERATION
Depress the test switch. The LED heads will light and the charge LED will extinguish. LED heads will illuminate as long as the button is
pushed. Release the test switch. The charge LED will illuminate and the LED heads will turn off.
MAINTENANCE: None required. Replace the batteries as needed according to ambient conditions. However, we recommend that the
equipment be tested regularly in accordance with local codes.
NOTE: Servicing of any parts should be performed by qualified personnel. Only use replacement parts supplied by Cooper Lighting Solutions.
CAUTION: This equipment is furnished with a sophisticated low voltage battery dropout circuit to protect the battery from over discharge after its
useful output has been used. Allow 24 hours recharge time after installation or power failure for 90 minute testing.
TROUBLE SHOOTING GUIDE
If LED heads or charge indicator LED does not illuminate, check the following:
1. Check AC supply – verify that unit has 24 hour AC supply.
2. Unit is shorted or battery is not connected.
3. Battery discharged. Permit unit to charge for 24 hours and then re-test.
4. If following the above trouble shooting hints does not solve your problem, contact your local Cooper Lighting Solutions representative for
assistance.
SCHEMATIC
JMP12
JMP11
JMP10
JMP9
JMP8
JMP7
JMP6
JMP5
JMP4
BATT
LAMPS
N
c
TDI
ICSP
277
JMP13
JMP14
LED/SW
D5
C6
C7
C8
C9
CN4
F1
J1
JK1
LED1
MOV1
MOV2
PR1
Q1
Q5
R7
R10
R13
R15
R18
R30
SW1
120
CN5
+
+
WHITE LEAD - TO NEUTRAL
BLACK LEAD - TO 120V
ORANGE LEAD - TO 277V
CHARGER/DRIVER PCB
BATTERY
LED HEADS
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
770.486.4800 Fax: [phone]
7/20/12 049-220