Courtyard Creations TGS62HS-WM User manual

PARTS LIST
PART
NO. PART QT’Y PART NO. PART QT’Y
1 1
1
1
2
2
4
7 12
12
12
1
1
248
9
10
11
12
2
3
4
5
6
TGS62HS-CS05-1
TGS62HS-CS04-2
TGS62HS-CS04-1
62TGS62HSY101
62TGS62HSY102
17C17A0403001Y4
17C01A0721091Y4
17FA05040301-Y4
18000C23001
18000337002
17KAB1101----Y4
17KAA0201----Y4
TABLE TOP
LEG
SUPPORT
CENTER CONNECTOR
CENTER CONNECTOR WITH RING
SCREW ST4.2*12
BOLT M6*60
WASHER d6.5*D13*1.0
BOLT CAP M6
HEX.KEY WRENCH 6MM
PLASTIC NUT M6*P1.0
NUT WRENCH 10&13MM
Step 1:
Place the table top (#1) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Insert the legs (#3) and the supports (#2) into the
plastic holders on the table top (#1) rim by using
screws (#6). See Figure 1.
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS62HS-WM
COURTYARD CREATIONS INC.
!
!
!
!
!
!
!
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #11)
- Nut Wrench (See Part #12)
MATERIAL CODE MATERIAL CODE
FIGURE 1 3
6
3
33
2
STOP DON’T RETURN TO STORE!
Use the correct bolts as indicated. Do not tighten any of the bolts until the table is completely assembled.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 2
2
1

PAGE 2 OF 2
Step 4:
Turn the table to its upright position. See Figure 4.
Note:
To use an umbrella with this table, remove the plastic
center plug and put the umbrella pole through the table
top (#1) and center connector ring (#4).
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame parts.
• Wash glass with mild soap and water, rinse thoroughly, and dry completely.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your table.
• When moving the table, remove the umbrella and lift. Do not drag this table.
• We recommend the use of furniture covers when not in use.
• In order to prolong the life and beauty of your table, we recommend that it be stored in a dry and protected
area during off season periods.
• Tempered glass has been used for increased strength and safety of your table. However, during windy
conditions the umbrella should be lowered and/or removed.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
FIGURE 2
FIGURE 4
FIGURE 3
Step 2:
Fasten the center connector (#5) to the middle of the
legs (#3) and the supports (#2) by using bolts (#7),
washers (#8), and plastic nuts (#9). Keep the bolts
loose. See Figure 2.
Step 3:
Fasten the center connector with ring (#4) to the
middle of the legs (#3) and the supports (#2) by using
bolts (#7), washers (#8), and plastic nuts (#9). Make
sure that all of the bolts have been tightened completely
and cover them with bolt caps (#10). See Figure 3.
333333
33
7
88
910 7
8
8
910
22
22
54
STOP DON’T RETURN TO STORE!