Courtyard Creations TGS63SW-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS63SW-WM
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 2 COURTYARD CREATIONS INC.
!
!
!
!
!
!
!
STOP DON’T RETURN TO STORE!
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1 1
2
3
4
5
7
8
9
10
11
48
4
4
1
4
2
1
6
TGS63SW-CS01
TGS63SW-CS02
TGS63SW-CS03
62TGS63SWY101
17C17A0403001Y4
17C01A0709001Y4
17FA05040301-Y4
18000337004
18000337001
17KAA0101----Y4
TABLE TOP
LEG
SUPPORT
CENTER
CONNECTOR WITH RING
SCREW ST4.2*12
BOLT M6*25
WASHER d6.5*D13*1.0
BOLT CAP
BOLT CAP M6
HEX.KEY WRENCH 4MM
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
FIGURE 1
22
33
5
5
2
1
2
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #11)
Step 1:
Place the table top (#1) onto a non-abrasive surface, such as a
carpet, with its underside facing upwards. Insert the legs (#2)
and the supports (#3) into the plastic holders attached on the
underside of the table top (#1) rim. Fasten them together by
using screws (#5). See Figure 1.
6 4
17C33A0709001Y4
BOLT M6*25

Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
FIGURE 2
FIGURE 4
25
#6 BOLT M6*25
FIGURE 3
7
8
10
7
8
10
25
#7 BOLT M6*25
Step 2:
Fasten the center connector with ring (#4) to the middle of the
legs (#2) by using bolts (#6) and washers (#8). Keep the bolts
loose. See Figure 2.
Note:
The arrow marks on the center connector with ring (#4) should
coincide with Figure 2 to ensure proper assembly.
Step 3:
Fasten the center connector with ring (#4) to the supports (#3)
by using bolts (#7) and washers (#8). Make sure that all of the
bolts have been tightened completely and cover them with bolt
caps (#9 and #10). See Figure 3.
Cleaning and Maintenance
•Wash frame parts w ith mild soap and water, rinse thoroughly,
and dry completely. Do not use bleach, acid, or other solvents
on the frame parts.
•Wash glass with mild soap and water, rinse thoroughly,
and dry completely.
• Inspect and tight en all bolts and fasteners on a regular basis
to ensure the proper performance and safety of your table.
•When moving the table, remove the umbrella and lift. Do
not drag this table.
• We recommend the use of furniture covers when not in use.
•In order to prolong the life and beauty of your table, we
recommend that it be stored in a dry and protected area
during off season periods.
• Tempered glass has been used for increased strength and
safety of your table. However, during windy conditions the
umbrella should be lowered and/or removed.
Step 4:
Turn the table to its upright position. See Figure 4.
Note:
To use an umbrella with this table, remove the plastic center
plug and put the umbrella pole through the table top and
center connector ring.
9
6
22
2
222
2
2
3333
44
8
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.