Craftsman Workbench User manual

OPERATOR'S MANUAL
CRRFTSMRN °
WORKBENCH
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA.
F1483

fSAFETY WARNINGS AND CAUTIONS:
Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage.
Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage.
• DO NOT stand on this product. You may fall which may cause personal injury.
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
Appropriately secure this product before moving it with a forklift.
• DO NOT tow with power equipment. The product could tip, which may cause personal injury or product damage.
• DO NOT alter this product in any manner. For example, do not weld external Iockbars or attach electrical equipment. This may cause
product damage or personal injury.
Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may cause
personal injury or product damage.
• BE CAREFUL when opening more than one drawer. The product may become unstable and tip, which may cause personal injury or
product damage.
• DO NOT step in the drawers. You may fall which may cause personal injury.
The maximum weight for each drawer should be no more than 35 pounds.
Maximum combined weight limit not to exceed 1,450 pounds. If the limit is exceeded, the product could collapse and cause personal injury
or product damage.
k. j
Tools Required: Hardware Included:
3/8" Wrench
7/16" Wrench AA (34) EE (34)
11/32" Wrench
Drill
1/8" Drill bit
Screwdriver, Phillips
Screwdriver, Flathead BB (20) FF (34)
CO (12) _GG (12)
DD (6)
(Call 1-800-4MY-HOME (1-800-469-4663) for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts. )

C(4)
D(3)
G(6)
E(2)
A(2) B(2)
H(3)
J

f
STEP1
AA (16)
BB (8)
EE (16)
FF (16)
Attach B to A with BB.
(2)
Assemble A(2) and C(4).
EE
FF
AA
C (4)
Square unit and wrench tighten to 40-50 in/Ibs. (Finger
tighten and approximately 1/2 wrench turn).
J
fSTEP 2
AA(10)
EE (10)
FF (10)
Note: It may be easier to turn unit upside down for steps 2 and 3.
• Attach D(3).
D (3)
AA
FF
EE
EE
AA
Wrench tighten to 40-50 in/Ibs (finger tighten and
approximately 1/2 wrench turn).
J

f
STEP3
AA (8)
EE(8)
FF (8)
Attach E(2).
FF
EE
(2)
Wrench tighten to 40-50 in/Ibs (finger tighten and
approximately 1/2 wrench turn).
f
STEP 4
Release
BB(12)
CC (12)
GG (12)
Separate slide parts.
Gu
Gd
Release:
Raise or lower
Attach (2) Gd to each H.
Wrench tighten.
-H (3)
J

fSTEP 4Continued
Attach Gu(6) to unit.
I#[O]llll_l
Gu (6)
BB
NOTE: Drawers may be organized in several configurations,
below is the slide positioning for the recommended drawer
configuration.
:::::::::: F
:::::::::: a
.......... O
N
T
-N fSTEP 5
If Backwall with Metal Pegboard is purchased with
this Workbench, see Backwall instructions for
assembly before continuing to assemble the
Workbench. Do NOT assemble top before returning
to these instructions.
Position J as desired.
Mark centers of (6) square mounting holes.
Square
Mounting
Hole_
Turn J over. (Use packaging material to avoid scratching).
Drill (6) 1/8" pilot holes 1/2" deep.
.)

fSTEP 5 - Continued
• Reposition J on unit.
• Attach with DD (6).
DD(6)
f
STEP 6
Insert the drawer slides (Gd) into the workbench slides
(Gu) and push all of the way to the back.
Pull the drawer open until it stops to ensure proper
assembly.
Carefully align slides and
push drawer into
unit until drawer stops.
J

f
REMOVING AND INSTALLING DRAWERS:
Empty the drawer.
Fully extend the drawer.
Release
Lever style- Lift or lower (depending on the slide) the
release lever on both sides and pull drawer out to
remove.
Tab style- Depress the release tabs on both sides and
pull drawer out to remove.
To reinstall, carefully align the slides and push the
drawer into the unit until the drawer stops.
t_. Lubricate the slides with grease or equivalent, (twice
yearly).
• Periodically the drawer fronts, drawer trim, and other
surfaces should be cleaned with a mild detergent and water.
• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
• Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning
fluid.
k.

MANUAL DE USUARIO
CRRFTSMRN °
BANCO DE TRABAJO
ATENClON: Lea y siga todas las Normas de Seguridad y las Instrucciones de Funcionamiento antes de
utilizar por primera vez este producto.
Sears, Roebuck and Co., Hoffman Estates, lL 60179, USA. F1483

fADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD:
Utilice un equipo de seguridad apropiado cuando use herramientas electricas y manuales. De Io contrario podria ocasionarse lesiones
personales o dafiar el producto.
Utilice el personal adecuado para el montaje y el traslado de esta unidad. De Io contrario podria ocasionarse lesiones personales o dafiar
el producto.
NO se ponga de pie encima de este producto. Podria caerse y causarse lesiones personales.
NO monte este producto en la plataforma de un cami6n ni en ning_n objeto en movimiento. Esto podria causarle lesiones personales o
daSar el producto.
Asegure de forma adecuada este producto antes de moverlo con una carretilla elevadora.
NO Io remolque con equipo electrico. El producto podria volcar Io que podria causarle lesiones personales o dafiar el producto.
NO altere este producto de modo alguno. Esto podria daSar el producto o causarle lesiones personales.
Mantenga el producto sobre superficies planas. El producto puede desestabilizarse y volcar si se almacena o se mueve en superficies no
lianas, Io cual podria causar lesiones personales o dafiar el producto.
TENGA CUIDADO al abrir mas de un cajon. El producto podria desestabilizarse y volcar Io que podria causarle lesiones personales o
dafiar el producto.
NO se ponga de pie encima de los cajones. Podria caerse y causarse lesiones graves.
El peso maximo en cada gaveta no debe ser mayor de 35 libras.
El peso maximo combinado no debe exceder alas 1,450 libras. Si se excede este limite, el producto podria derrumbarse y causar lesiones
personales o dafiar el producto. ,J
Herramientas necasarias: Ferreteria incluida:
Llavelnglesade3/8" /_ \
Llave inglesa de 7/16" AA (34) _ EE (34)
Llave Inglesa de 11/32"
Talladro
Broca de 1/8 de pulgada
Destomillador Philips BB (20) _ FF (34)
Destomillador
de cabeza plana
CC (12) _GG (12)
DD (6)
Llame al 1-800-659-7084 para Piezas de Servicio. Consulte el dibujo de piezas de servicio si desea un listado completo de piezas de servicio) i