Craftsman Workbench User manual

OPERATOR'S MANUAL
ICRFIFTSM FIN°I
WORKBENCH
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA. F1495

SAFETY WARNINGS AND CAUTIONS:
•Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage.
• Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage.
•DO NOT stand on this product. You may fall which may cause personal injury.
• DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
• Appropriately secure this product before moving it with aforklift.
• DO NOT tow with power equipment. The product could tip, which may cause personal injury or product damage.
• DO NOT alter this product in any manner. For example, do not weld external tockbars or attach electrical equipment. This may cause
product damage or personal injury.
• Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an un-level surface, which may cause
personal injury or product damage.
• BE CAREFUL when opening more than one drawer. The product may become unstable and tip, which may cause personal injury or
product damage.
• DO NOT step in the drawers. You may falt which may cause personal injury.
• The maximum weight for each drawer should be no more than 35 pounds.
• Maximum combined weight limit not to exceed 1,450 pounds. If the limit is exceeded, the product could collapse and cause personal injury
or product damage.
Tools Required: Hardware Included:
3/8" Wrench
7/16" Wrench
11/32" Wrench
Drill
1/8" Drill bit
Screwdriver, Phillips
Screwdriver, Flathead Separate
Bag
AA (24)
BB (36)
,;'/- -\
( ,
\\ j
EE (24)
FF (24)
CC (28)
DD (6)
i
GG (28)
HH (8)
iCall 1-800-4MY-HOME (1-800-469-4663) for Service Parts. Refer to Service Parts Drawing for fult listing of Service Parts. )

F
/
/
/
A(2)
/
/
/
/
/
/
/
B(2)
E(14)
/
/
//
,/
/
..............G(7)
_D(2)
k. ,J

r
STEP1
_=llll
AA (24)
BB (8)
EE(24)
FF (24)
Attach Bto A using BB
Wrench tighten. (Do not overtighten).
B (2) .A(2)
Assemble A(2), C(4), and D(2).
J
/
A(2) C (4)
D(2)
Finger tighten. (Do not wrench tighten until step 3).
r
STEP 2
BB (28)
4
CC (28)
GG (28)
• Separate slide parts. (See drawer removal instructions).
Eu
Ed
• Attach (2) Ed to each G.
Release ............. G (7)
............GG
/"
/,
Ed (14)
• Wrench tighten.
,J

r
STEP 2 Continued
• Attach Eu(14) to unit.
,:,:,:.:.:
"::i!
\. \\
NOTE: Drawers may be organized in several configurations,
below is the slide positioning for the recommended drawer
configuration.
F
r
0
n
t
--i C--
......./ .......
Left side
_i .......... i_ i
.......... E_
J
iS _,ii
Right side
F
r
0
n
t
STEP 3
Insert the drawer slides (Ed) into the workbench slides
(Eu) and push all of the way to the back.
Pull the drawer open until it stops to ensure proper
assembly.
Repeat for remaining drawers.
Carefully align slides and
slowly push drawer into
unit until drawer stops.
Square the unit and adjust for optimum drawer
performance.
Wrench tighten (24) fasteners from step1 to 40-50 in/lbs
(finger tighten and approximately 1/2 wrench turn).
Remove drawers. (See drawer removal instructions).
STEP 4
• Position F as desired.
• Mark centers of (6) square mounting holes.
F \ //_ _'\"--.
Square
Mounting.....
Hole ........

STEP 4 - Continued
Turn F over. (Use packaging material to avoid scratching).
Drill (6) 1/8" pilot holes 1/2" deep.
f
STEP 4 -Continued
DD(6)
Reposition F on unit.
_J\\.\
/. \,
\\\\\
DD (6)
Attach using DD 88).
Reinstall drawers. (See drawer installation instructions).
REMOVING AND INSTALLING DRAWERS:
• Empty the drawer.
• Fully extend the drawer.
Release _
Lever style- Lift or lower (depending on the slide) the
release lever on both sides and pull drawer out to
remove.
Tab style- Depress the release tabs on both sides and
pull drawer out to remove.
To reinstall, carefully align the slides and push the
drawer into the unit until the drawer stops.
Lubricate the slides with grease or equivalent, (twice
yearly).
Periodically the drawer fronts, drawer trim, and other
surfaces should be cleaned with a mild detergent and water.
Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning
fluid.
J

MANUAL DE USUARIO
ICRAFTSMI_N°l
BANCO DE TRABAJO
ATENClON" Lea y siga todas las Normas de Seguridad y las Instrucciones de Funcionamiento antes de
utilizar por primera vez este producto.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA. F1495

r
ADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD:
•Utilice un equipo de seguridad apropiado cuando use herramientas electricas y manuales. De 1ocontrario podria ocasionarse lesiones l
personales o dafiar el producto. |
• Utitice el personal adecuado para el montaje y el traslado de esta unidad. De 1ocontrario podria ocasionarse lesiones personales o dafiar _
el producto. |
•NO se ponga de pie encima de este producto Podria caerse y causarse tesiones personales |
• NO monte este producto en la plataforma de un cami6n ni en ningQn objeto en movimiento Esto podria causarle lesiones personales o l
dafiar el producto. |
• Asegure de forma adecuada este producto antes de moverto con una carretitta elevadora. |
•NO 1oremolque con equipo electrico El producto podria volcar to que podria causarle tesiones personales o dafiar el producto |
• NO altere este producto de modo alguno Esto podria dafiar el producto o causarte lesiones personales |
• Mantenga el producto sobre superficies planas El producto puede desestabilizarse y volcar si se almacena o se mueve en superficies nol
lianas, 1ocual podria causar tesiones personales o dafiar el producto. |
• TENGA CUlDADO al abrir m_ts de un caj6n. El producto podria desestabilizarse y volcar 1oque podria causarle lesiones personales o l
dafiar el producto. |
• NO se ponga de pie encima de los cajones. Podria caerse y causarse lesiones graves. /
°Et peso maximo en cada gaveta no debe ser mayor de 35 tibras. |
• El peso maximo combinado no debe exceder alas 1,450 libras. Si se excede este limite, el producto podria derrumbarse y causar lesiones _
personales o dafiar el producto. J
Herramientas necasarias: Ferreteria incluida:
Llave Ingtesa de 3/8"
Llave ingtesa de 7/16"
Llave Inglesa de 11/32"
Talladro
Broca de 1/8 de pulgada
Destornittador Philips
Destornillador
de cabeza plana
AA (24) EE (24)
'\\\
Bolsa BB (36) FF (24)
Separada
CC (28) GG (28)
DD (6) '\'\ HH (8)
h '
I
/ /

F
C(4) -..
A(2)
/
/
./
iiii!iiiii'ii
iiii!i!iii ii
'.:.:.:. ii
ii.
//
/'
/
B(2)
/'
//
/'
/
E(14)
/
/
//
./
/
/
/
/
...............G(7)
_D(2)

r
PASO1
AA(24)
BB (8)
EE (24)
\\\ /
FF (24)
Cotoque Ben A usando BB.
Apriete con llave. (No apriete demasiado.)
B (2) A (2)
Colocar A(2), C(4), y D(2).
FF
EE
\\\
/ii '
I
/
Apriete a mano. (No apriete con llave hasta el paso 3).
J
fPASO 2
BB (28)
CC (28)
GG (28)
Separe tas piezas de tas guias. (Veanse las instrucciones
para retirar las gavetas).
Eu
Ed
• Coloque (2) Eden cada G.
Liberacibn G (7)
CC
GG
/
Ed (14)
• Apriete con la llave inglesa.
,J