Crestron FlipTop FT2A-CBLR-1T Series User manual

The Crestron® FT2A-CBLR-1T series FlipTop™ One-Touch Cable
Retractors provide an assortment of retractable cables for use with the
FT2-ELEC assembly cable management systems (not included). Each
model features a retractable cable that may be pulled out up to 5ft
(1.52m). When the cable retractor button on the included module is
pressed, the cable retracts gently back into its retractor enclosure.
The FT2A-CBLR-1T series retractor attaches to the side of the assembly
underneath the table. Each FT2A-CBLR-1T series pass-through module is
1.97x1.97in. (50x50mm) and occupies two module spaces in the
FT2-ELEC assembly.
FT2-ELEC assembly and FT2A-CBLR-1T Series Retractor
In the Box
1 FT2A-CBLR-1T Series, FlipTop™ One-Touch Cable Retractors
Additional Items
FT2A-CBLR-1T-4K-DP and FT2A-CBLR-1T-4K-DP-HD Only
1 DisplayPort™ pass-through module (4526967)
FT2A-CBLR-1T-4K-MDP-DP and FT2A-CBLR-1T-4K-MDP-HD Only
1 Mini DisplayPort pass-through module (4526968)
FT2A-CBLR-1T-4K-USBC-HD Only
1 USB Type-C® pass-through module (4526983)
FT2A-CBLR-1T-AUDIO Only
1 Stereo audio pass-through module (4526980)
FT2A-CBLR-1T-CAT6 Only
1 LAN pass-through module (4526981)
FT2A-CBLR-1T-HD Only
1 HDMI® pass-through module (4526361)
FT2A-CBLR-1T-USB Only
1 USB 2.0A adapter (2053204)
1 USB pass-through module (4526982)
FT2A-CBLR-1T-USBC-PWR Only
1 Reclosable fastener strips (2 pieces together) (2005411)
1 USB Type-C pass-through module (4526983)
FT2A-CBLR-1T-VGA Only
1 VGA pass-through module (4526969)
1
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Install the Retractor
Install the FT2A-CBLR-1T series retractors into an FT2-ELEC assembly
previously mounted into a table. Complete the FT2A-CBLR-1T series
installation before installing the FT2A-CBLR-1T series pass-through
module.
NOTES:
lThe FT2A-CBLR-1T series retractors are installed at the end of
the module rows on either side of the FT2-ELEC assembly
enclosure. If a FT2A-CBLR-BRKT (not included) is used, the
bracket and retractor are installed to the front and/or rear of
the FT2-ELEC assembly.
lThe FT2A-CBLR-1T series retractors extend 11.16in. (283mm)
vertically and 8.32in. (212mm) horizontally underneath the table.
lThe amount of retractor mounting locations (four keyed slots)
varies for each FT2-ELEC assembly. For example, if installing
the retractor into an FT2-700-ELEC device, there are four
possible locations (two per side).
1. Pull the cable connector out of the retractor and tuck it underneath
the FT2-ELEC assembly.
2. Align the four keyed tabs on the retractor neck with the four keyed
slots on the FT2-ELEC assembly. Then, push the retractor up and into
the slots so that the keyed tabs engage the wide end of the slots.
3. Slide the retractor downward until the keyed tabs are secured inside
the narrow end of the slots.
NOTE: Once the FT2A-CBLR-1T series retractor is secured into the
FT2-ELEC assembly, a locking tab prevents the retractor from being
easily removed. To remove the retractor after it has been installed,
press the locking tab while pulling the retractor up and out of the slots
in the assembly.
2
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Install the USB-C® Power Adapter
FT2A-CBLR-1T-USBC-PWR Only
The FT2A-CBLR-1T-USBC-PWR is a USB-C® to USB-C power module
that supports device charging only. The male USB Type-C® connector
must connect to a 60 W USB-C power adapter (not included). To attach a
USB-C adapter to the FT2-ELEC assembly, use the included reclosable
fastener strips. One fastener strip is placed on the FT2-ELEC assembly
and the other strip is placed on the adapter.
NOTES:
lThis procedure is intended for the FT2A-CBLR-1T-USBC-PWR
retractor only.
lWhen preparing to attach the fastener strips to the USB-C
adapter and FlipTop assembly, make sure that there will be
enough room on the enclosure to also attach an
FT2A-UTK-PWS power supply or another FlipTop accessory
beside the adapter.
3
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

1. Remove the protective backing from one fastener strip.
2. Align the edges of the fastener strip with the bottom and side edges of
the FT2-ELEC assembly.
3. Press the fastener strip firmly onto the FT2-ELEC assembly.
4. Remove the protective backing from the remaining fastener strip, and
press it firmly onto the power adapter.
5. Align the power adapter's fastener strip with the assembly's fastener
strip, and press the adapter firmly onto the FT2-ELEC assembly.
NOTE: Ensure the reclosable fastener strips are locked together.
4
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Install the Module
Use the following procedure to install the FT2A-CBLR-1T series pass-
through module into an FT2-ELEC assembly. If the FT2A-CBLR-1T series
pass-through module is being installed as part of a new FT2-ELEC
assembly installation, proceed to Insert the Cable into the Module.
Prepare the FT2-ELEC assembly
1. Remove the magnetic bezel from the FT2-ELEC assembly by grasping
the inside of the bezel and pulling it up and away firmly from the
assembly until the magnetic hold is broken.
2. Unscrew and remove the two locking bars on either side of the module
row that is required for installation. For example, if installing the
FT2A-CBLR-1T series pass-through module in the bottom row of an
FT2-700-ELEC device, remove the middle and bottom locking bars.
Insert the Cable into the Module
1. Push down on the two door removal tabs on the bottom of the
FT2A-CBLR-1T series pass-through module to open the module door.
2. Route the cable connector through the bottom of the module, and
then thread the cable sideways through the slot in the module door so
that the connector exits the inside of the door.
5
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

3. Snap the door back into place to secure it to the module.
FT2A-CBLR-1T Series Pass-Through Module (Bottom View)
FT2A-CBLR-1T Series Pass-Through Module (Top View)
Install the Module into the FT2-ELEC Assembly
1. Orient the module so that its LED is facing toward the front of the
FT2-ELEC assembly as shown in the following illustration. 2. Feed the module’s power cable down through the appropriate module
slot in the FT2-ELEC assembly.
6
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

3. Push the module down into the appropriate module slot in the
FT2-ELEC assembly so that the module slides into place. Use the guide
ribs on the front and rear of the module to help position the module in
the assembly.
4. Route the module’s power cable through the wire saddle on the
retractor, and then connect the cable to the retractor as shown in the
following illustration.
CAUTION: If the FT2A-CBLR-1T series pass-through module or
retractor must be removed from the FT2-ELEC assembly,
disconnect the module power cable from the retractor prior to
removal.
7
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Enable Automatic Cable Retraction (Optional)
A network connection between the FT2-ELEC assembly and a Crestron
control system or DMPS3 enables remote control of the installed
FT2A-CBLR-1T series. For example, when a networked FT2-ELEC
assembly with a one-touch cable retractor is installed in a room with an
occupancy sensor and the sensor detects an unoccupied room, the
FT2-ELEC assembly communicates with the system to automatically
retract the cable.
On an FT2-ELEC assembly using standard Cresnet® cable, connect the 3-
pin connector to a Crestron control system or DMPS3.
NOTE: The red power lead should not be connected.
To ensure that the FT2A-CBLR-1T series retractor retracts automatically,
FT2A-CBLR-1T series check the following:
lThe FT2A-CBLR-1T series pass-through module is properly seated
within the FT2-ELEC assembly.
lThe FT2A-CBLR-1T series pass-through module’s power cable is
properly connected to the FT2A-CBLR-1T series retractor.
lThe 3-pin connector on the FT2-ELEC assembly is connected properly
to the Crestron control system or DMPS3.
Install the Locking Bars
1. Place the locking bars into position so that the screws attached to the
locking bars engage the screw holes in the FT2-ELEC assembly.
2. Using a manual torque screwdriver set to its lowest possible setting,
hand tighten the locking bar screws until the locking bars are secured
to the FT2-ELEC assembly.
CAUTION: Do not overtighten the locking bar screws.
8
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Install the Bezel
Place the bezel onto the FT2-ELEC assembly so that the retractable lid
fits inside the bezel opening. The bezel is held in place using magnets. Operate the Cable Retractor Button
Press the cable retractor button to retract the cable back into its seat.
The LED backlight provides the cable connector status.
lSolid: The cable retracted successful.
lFlashing: The cable did not fully retract after the cable retractor
button was pressed. Remove obstruction to free cable. Once the cable
connector returns to its seat within the module, the LED indicator
stops flashing and returns to solid.
9
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors

Visit the Product Page
Scan the QR code to visit the product page.
FT2A-CBLR-1T Series
www.crestron.com/model/6508381
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, and FlipTop are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the
United States and/or other countries. USB-C and USB Type-C are either trademarks or
registered trademarks of USB Implementers Forum, Inc. in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be
used in this document to refer to either the entities claiming the marks and names or
their products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8220C
02/21/20
10
FT2A-CBLR-1T Series QuickStart
FlipTop™ One-Touch Cable Retractors