Crestron ZUMMESH-JBOX-DALI User manual

The Zūm™ Wireless ZUMMESH-JBOX-DALI is a single-
channel DALI controller capable of controlling up to 64
DALI compatible drivers. The ZUMMESH-JBOX-DALI
communicates with other Zūm devices such as keypads,
occupancy sensors, vacancy sensors, and daylight sensors.
NOTE: The ZUMMESH-NETBRIDGE (sold separately)
is required to create and control DALI groups. The
ZUMMESH-NETBRIDGE must be connected to the
ZUMMESH-JBOX-DALI for DALI group control.
Check the Box
Item Qty
ZUMMESH-JBOX-DALI 1
Nut, Wire Twist, Yellow, 22-10 AWG
(P/N 2049245)
4
Nut, Lock, 1/2 in. - 14, Conduit, Steel
(P/N 2047626)
1
Installation
WARNING: To avoid fire, shock, or death, turn off the power
at the circuit breaker or fuse and test that the power is off
before wiring!
NOTE: Observe the following points:
• Install and use this product in accordance with
appropriate electrical codes and regulations.
• A licensed electrician should install this product.
• The product projects 3-11/16 in. (93 mm) from the
junction box when installed.
To install a ZUMMESH-JBOX-DALI:
1. Turn the power off at the circuit breaker.
2. Mount the ZUMMESH-JBOX-DALI to the J-box using
a locknut.
3. Wire the ZUMMESH-JBOX-DALI as shown.
To DALI
controlled loads
DALI Input/Output
(purple)
DALI Input/Output
(gray)
Neutral
(white)
Hot
(black)
100-277 VAC
power from
breaker
To install a ZUMMESH-NETBRIDGE:
NOTE: For product specifications and additional installation
details, refer to the ZUMMESH-NETBRIDGE Installation
Guide (Doc. 7955) at www.crestron.com/manuals for
details.
1. Use a flat-head screwdriver to remove the cover on
the ZUMMESH-JBOX-DALI. Insert the flat-head
screwdriver into the slot next to the cover and pry up
to remove the cover.
2. Align the ports on the ZUMMESH-NETBRIDGE
and the ZUMMESH-JBOX-DALI, and then
insert the ZUMMESH-NETBRIDGE into the
ZUMMESH-JBOX-DALI. The J-box module snaps into
place.
120 - 277 VAC power
from breaker
Neutral
(white)
Hot
(black)
100-277 VAC
power from
breaker
Operation
Prior to room commissioning, the ZUMMESH-JBOX-DALI
uses DALI broadcast to control all connected
lights simultaneously. After commissioning the
ZUMMESH-JBOX-DALI, addressing devices and creating
groups, the ZUMMESH-JBOX-DALI will control drivers
assigned to the groups.
NOTES: Connect the ZUMMESH-NETBRIDGE (sold
separately) directly to the ZUMMESH-JBOX-DALI to create
and control DALI groups. The ZUMMESH-JBOX-DALI
functions in broadcast mode if the ZUMMESH-NETBRIDGE
is not connected.
Test the Ballasts
To verify that all drivers have been properly wired, press
the TEST button to toggle the drivers that are assigned to
groups.
To test the dimming function of the drivers, press and hold
the TEST button.
NOTE: if the ZUMMESH-JBOX-DALI is not commissioned,
the device operates in DALI broadcast mode and
controls all of the connected drivers simultaneously.
After the ZUMMESH-JBOX-DALI is commissioned, the
ZUMMESH-JBOX-DALI only toggles or dims drivers that
are assigned to groups.
Commissioning
Use the Crestron Zūm app to commission the
ZUMMESH-JBOX-DALI.
For details on commissioning, refer to the Zūm Light
Control System Product manual (Doc. 7957)
at www.crestron.com/manuals.
ZUMMESH-JBOX-DALI
Zūm™ Wireless DALI® Controller

Factory Reset
Perform a factory reset when the ZUMMESH-JBOX-DALI is
removed from the network or to remove the configuration
settings from the device. The ZUMMESH-JBOX-DALI must
also be factory reset if it is being moved to a different
system.
NOTE: New-in-box devices do not need to be factory reset
before joining a system.
To factory reset the ZUMMESH-JBOX-DALI, press and hold
the SETUP and TEST buttons until the SETUP LED lights
(about 10 seconds), and then release both buttons. The
SETUP LED and the connected load output turn on.
TEST
SETUP
TEST
SETUP
Press and hold SETUP and
TEST until the LED flashes
Additional Information
Scan or click the QR code for detailed product information.
ZUMMESH-JBOX-DALI
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original
instructions. All other languages are a translation of the original instructions.
Regulatory Model: M201904001
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
This product is Listed to applicable UL® Standards and requirements tested by
Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par
Underwriters Laboratories Inc.
This product conforms to ANSI/UL STD 2043 tested by Intertek® services.
The product meets the requirements of UL 2043 for installation in an
environmental air-handling (plenum) space, such as above a suspended ceiling.
The product is tested by an NRTL (Nationally Recognized Testing Laboratory)
and complies with ANSI/UL2043 (Fire Test for Products Installed in Air-
Handling Spaces). Full compliance requires plenum rated cables.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific
information, please
visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Zūm are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. UL and the UL logo are either trademarks or registered trademarks
of Underwriters Laboratories, Inc. in the United States and/or other countries.
Intertek is either a trademark or registered trademark of Intertek Group in the
United States and/or other countries. The ETL logo is either a trademark or
registered trademark of Intertek Testing Services NA in the United States and/
or other countries. DALI is either a trademark or registered trademark of ZVEI
- Zentralverband Elektrotechnik- und Elektronikindustrie in the United States
and/or other countries. Other trademarks, registered trademarks, and trade
names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest
in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: [phone]
www.crestron.com
Quick Start - Doc. 8448A
(2053429)
11/06/19
Specifications subject to
change without notice.