Crestron MPC-M5 Dimensional drawing

DO GUIDE
4. Attach cables to the rear of the MPC-M5. Make the connections as called out in the following illustration.
Apply power after all connections have been made. When making connections to the MPC-M5, use Creston®power supplies for Crestron
equipment.
5. Use the two included 4-40 x 1/4˝ screws to attach the MPC-M5 to the mounting plate.
CAUTION: Excess wire that is pinched between the MPC-M5 and the electrical box could short out. Make sure that all wires are completely inside
the electrical box and not between the box and the MPC-M5.
a. Attach the label holder by placing it over its slots and sliding it downward into position.
b. Attach the included labels in the appropriate positions on the MPC-M5.
MPC-M5
Media Presentation Controller
DO Install the MPC-M5 Wiring
Install a standard 2-gang electrical box (not supplied) in a wall or podium.
1. Route all required COMPUTER, LAN, COM, IR, I/O and/or RELAY wiring to the electrical box.
CAUTION: Incorrect wiring may damage the MPC-M5.
2. Depending on the application, the MPC-M5 inputs can be wired three ways.
* Detection of an occupancy sensor will also invert the SIMPL program logic: when the circuit is open (motion detected), the digital signal will be high; when the circuit is closed (no
motion detected), the digital signal will be low.
NOTE: The settings for the pull-down resistor are specied in the SIMPL Windows program. For more information, refer to the SIMPL Windows
help le.
DO Connect the MPC-M5
After the wiring has been installed and veried, attach the mounting plate to the electrical box.
1. Turn system power OFF.
2. Refer to the following illustration, and use the four included 6-32 x 3/4˝ screws to attach the mounting plate to the electrical box.
3. Connect the grounding wire from the mounting plate to an earth ground (building steel).
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Plate, Metal, Mounting, with Ground Wire 4510704
2 Screw, 4-40 x 1/4", Pan Head, Phillips 2007156
4 Screw, 6-32 x 3/4", Truss Head, Combo 2009211
1 Tool, 1/16" Allen Wrench, L-shape, 3" Blade 2022867
Items for MPC-M5-W Only
1 Labels, Actions, 100 Piece Set White 4509402
1Labels, Sources, 100 Piece Set White 4509400
1Plate, Front Panel White 4509213
4 Screw, 4-40 x 1/2", Button Head, Hex 2021396
Items for MPC-M5-B-T Only
1 Labels, Actions, 100 Piece Set Black 4509403
1Labels, Sources, 100 Piece Set Black 4509401
1Plate, Front Panel Black 4509214
4 Screw, 4-40 x 1/2", Button Head, Hex Black 2021395
Screws (4) 6-32 x 3/4"
Mounting plate
Ground wire COM:
To any
3-wire RS-232
device
RELAYS:
To controllable
devices
IR:
To IRP2 or
serial devices
I/O:
Inputs from
digital
devices
(and 24 volt
output power
for sensors)
LAN PoE:
10/100BASE-T Ethernet
to LAN or web
Button labels
Screws (2)
4-40 x 1/4"
Label holder
24 G 1 2
Detecting a oating contact
voltage (e.g., from a
Crestron®occupancy sensor)
Detecting a contact
voltage from a
switch or relay
Detecting a contact
closure from a
switch or relay
Pull-down
resistor:
enabled*
24 G 1 2
+
-
24 Vdc
Max
24 G 1 2
Crestron
occupancy
sensor

DO GUIDE DOC. 7716C (2042437) 07.16
Specications subject to change without notice.
6. Perform any necessary programming using the COMPUTER (USB) connection prior to attaching the front panel of the MPC-M5. (Programming can
also be performed via the LAN PoE port.)
7. Use the four included 4-40 x 1/2˝ screws and the included 1/16˝ Allen wrench to attach the front panel to the MPC-M5.
The following illustration shows an MPC-M5 in a commercial application.
DO Program the Pushbuttons
The 10 “hard key” pushbuttons on the MPC-M5 are programmable and can provide tactile control of many functions, such as power, source selection,
transport control, audio settings, lighting, and more. Refer to the following illustration for their assigned join numbers. A description for each button
signal is described in the SIMPL Windows help le.
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Conformité Reglementaire
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and
end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The specic patents that cover Crestron products are listed at patents.crestron.com. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, the MPC logo, and RoomView are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Blu-ray is either a trademark or registered trademark of the Blu-ray Disc Association (BDA) in the United States and/or
other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc..
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Screws (4) 4-40 x 1/2"
LAN
RELAY
IR
RS-232
LAN
VIDEO
RGB
AUDIO AUDIO
I/O
MPC-M5
POWER LIGHTS
OFF
LIGHTS
ON
SCREEN
DOWN
SCREEN
UP
VOLUME
DOWN
VOLUME
UP
DVD
LAPTOPPC
MPC-M5
ROOMVIEW
®
LAPTOP
BLU-RAY
PROJECTOR
PROJECTION
SCREEN
CRESTRON
OCCUPANCY
SENSOR
I/O
™
6
1 2 3
10
987
54
MPC-M5