Crestron DGE-100 Owner's manual

DGE-100/DM-DGE-200-C
Digital Graphics Engines
Supplemental Guide
Crestron Electronics, Inc.

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive,
non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron
dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron
website at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or
other countries. HDMI, the HDMI logo, and High Definition Multimedia Interface are either trademarks or registered trademarks of HDMI
Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.

Supplemental Guide – DOC. 7696B Contents
•
i
Contents
Access the Setup Screens 1
Configure the DGE 2
Ethernet Setup ........................................................................................................ 2
IP Table Setup ........................................................................................................ 3
Audio Setup ............................................................................................................ 5
Standby Timeout..................................................................................................... 6
Diagnostics ............................................................................................................. 7
Touch Test................................................................................................. 8
LAN Test.................................................................................................... 8
Test Patterns.............................................................................................. 9
HDMI Preview (DGE-100 Only)................................................................... 9
Local Video Preview (DM-DGE-200-C Only)............................................. 10
RTSP Test................................................................................................ 10
About .................................................................................................................... 11
Save & Edit ........................................................................................................... 11

Supplemental Guide – DOC. 7696B DGE-100/DM-DGE-200-C: Digital Graphics Engines
•
1
DGE-100/DM-DGE-200-C:
Digital Graphics Engines
Access the Setup Screens
The setup screens enable basic configuration prior to regular operation of the Crestron®
DGE-100 and DM-DGE-200-C.
The DGE-100 and DM-DGE-200-C are functionally similar. For simplicity within this guide,
the term “DGE” is used except where noted.
During regular operation of the DGE, there are two ways to access the setup screens:
1. Place a button on the project main page and assign the reserved join number
(17242) that accesses the setup screens.
2. Press the
SETUP
button on the DGE.
The main setup screen is displayed.
Setup Screen
The setup screen is composed of buttons for Ethernet setup, IP table setup, audio setup,
standby timeout, and diagnostics. In addition, there is a button to toggle system messages
on or off, an
About
button that provides information about the touch screen, and a
Save &
Exit
button. The functions of each are detailed in the following pages of this guide.

2
•
DGE-100/DM-DGE-200-C: Digital Graphics Engines Supplemental Guide – DOC. 7696B
Configure the DGE
Ethernet Setup
On the main setup screen, tap
Ethernet Setup
to display the
Ethernet Setup
screen.
Ethernet Setup Screen
The
Ethernet Setup
screen displays the DGE’s MAC and IP addresses, subnet mask,
default router, primary and secondary DNS, hostname, and domain. There are controls for
turning DHCP on and off, and when DHCP is off, a
Set Static IP Address Settings
button
provides access to controls that allow editing of these settings. This screen also contains a
link indicator to show the status of the Ethernet connection.
DHCP is enabled by default. To change to a static IP address, tap
Off
under
DHCP
Enabled
, and then tap
Set Static IP Address Settings
to display the
Ethernet Setup -
Static IPs
screen.
Ethernet Setup - Static IPs Screen
To edit the static IP address, static subnet mask, static default router, preferred DNS, or
alternate preferred DNS, tap the button directly under the label for the entry to edit. The on-
screen numeric keypad opens.

Supplemental Guide – DOC. 7696B DGE-100/DM-DGE-200-C: Digital Graphics Engines
•
3
On-Screen Numeric Keypad
Tap the “x” in the text field to clear any previous entry. Use the keypad to make the new
entry. Tap to delete the last digit. Tap
Save
to save the new entry or to
return to the
Ethernet Setup - Static IPs
screen.
After new settings have been saved, tap
Reboot
on the
Ethernet Setup - Static IPs
screen
to reboot the DGE so that the new settings can take effect.
If not making any changes, tap to return to the
Ethernet Setup
screen.
Tap again to return to the main setup screen.
IP Table Setup
On the main setup screen, tap
IP Table Setup
to display the
Ethernet Setup - IP Table
screen.
Ethernet Setup - IP Table Screen
The
Ethernet Setup - IP Table
screen displays up to four IP table settings, each of which
has an
Online
indicator. To add or edit an entry, tap the
Add/Edit
button to its left. The
Ethernet Setup - Edit IP Table Entry
screen is displayed.

4
•
DGE-100/DM-DGE-200-C: Digital Graphics Engines Supplemental Guide – DOC. 7696B
Ethernet Setup - Edit IP Table Entry Screen
Tap the field below
CIP ID
to display the on-screen hex keypad.
On-Screen Hex Keypad
Tap the “x” in the text field to clear any previous entry. Use the keypad to make the new
entry. Tap to delete the last digit. Tap
Save
to save the new entry or to
return to the
Ethernet Setup - Edit IP Table Entry
screen.
Tap the field below
IP Address/Hostname
to display the on-screen keyboard.

Supplemental Guide – DOC. 7696B DGE-100/DM-DGE-200-C: Digital Graphics Engines
•
5
On-Screen Keyboard
Tap the “x” in the text field to clear any previous entry. Use the keyboard to make the new
entry. Tap
Cancel
to return to the
Ethernet Setup - Edit IP Table Entry
screen. Tap
to delete the last digit. Tap
Save
to save the new entry and return to the
Ethernet Setup -
Edit IP Table Entry
screen.
On the
Ethernet Setup - Edit IP Table Entry
screen, tap
Save Entry
to save the current
entry or
Delete Entry
to clear it.
If not making any changes, tap to return to the
Ethernet Setup - IP Table
screen.
Tap again to return to the main setup screen.
Audio Setup
On the main setup screen, tap
Audio Setup
to display the
Audio Setup
screen.
Audio Setup Screen
The
Audio Setup
screen provides controls for muting or unmuting the audio, and for
adjusting levels for the master volume, media volume, and beep volume. The
Media
Volume
controls adjust the H.264 streaming media level in relation to the
Master Volume
controls.

6
•
DGE-100/DM-DGE-200-C: Digital Graphics Engines Supplemental Guide – DOC. 7696B
Tap to return to the main setup screen.
Standby Timeout
On the main setup screen, tap
Standby Timeout
to display the
Standby Timeout
screen.
Standby Timeout Screen
The
Standby Timeout
screen provides controls to adjust standby timeout from 0 to 120
minutes.
Tap
Screen Saver Options
to display the
Standby - Screen Saver
screen.
Standby - Screen Saver Screen
The
Standby - Screen Saver
screen provides controls to turn the digital clock screen saver
on and off, as well as controls to display the time in a 24-hour format and to adjust the
screen saver brightness.
Tap to return to the
Standby Timeout
screen.
Tap again to return to the main setup screen.