Crestron TST-600 User manual

Crestron TST-600
5.7” Wireless Touch Screen
Configuration Guide

The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Rava are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.

Crestron TST-600 5.7” Wireless Touch Screen
Configuration Guide – DOC. 7383D Contents
•
i
Contents
5.7” Wireless Touch Screen: TST-600 1
Access the Setup Screens........................................................................................................... 1
Configure the TST-600..............................................................................................................3
RF Setup ...................................................................................................................... 3
Audio Setup .................................................................................................................5
Display Setup .............................................................................................................. 5
Standby Timeout .........................................................................................................6
Networking Setup........................................................................................................ 7
Diagnostics ................................................................................................................ 13
About ......................................................................................................................... 14
Save & Exit ............................................................................................................... 14
Appendix A: The RF Spectrum .............................................................................................. 15
Appendix B: Optimum RF Reception Guidelines .................................................................. 16
Minimize Interference ............................................................................................... 16
Gateway Placement ................................................................................................... 16
Antenna Orientation .................................................................................................. 16

Crestron TST-600 5.7” Wireless Touch Screen
Configuration Guide – DOC. 7383D 5.7” Wireless Touch Screen: TST-600
•
1
5.7” Wireless Touch Screen:
TST-600
Access the Setup Screens
The main menu is the starting point for configuring the TST-600 from Crestron®.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
TST-600 defaults to the main menu.
The setup screens enable basic configuration procedures prior to regular operation of
the TST-600.
If a project is running, the main menu can be accessed using one of three methods:
via the trigger keys on the top of the touch screen, via front panel buttons on the left
side of the touch screen or via Crestron Toolbox™.
Via the Trigger Keys 1. Press and hold the left trigger key on the top of the touch screen until the
unit resets (approximately 5 seconds).
2. When the display turns black, then displays a “3”, release the trigger key.
3. When “Loading Crestron Applications…” appears on the display, touch the
screen.
4. Release the touch screen when “Preparing to enter setup” appears.
Via Front Panel Buttons The main menu can also be accessed by pressing HOME, MEDIA, ▲and ▼, on
the left side of the touch screen display, in sequence twice (press HOME, MEDIA,
▲,▼, HOME, MEDIA, ▲,▼) within a 5 second period.
Via Crestron Toolbox
1. Establish communication with the touch screen.
2. Right-click on the device and select Functions | Setup Mode….
3. Select Enter Setup Mode. The main menu is displayed, as shown in the
illustration below.
NOTE: Select Exit Setup Mode to exit the setup menu.

5.7” Wireless Touch Screen Crestron TST-600
2
•
5.7” Wireless Touch Screen: TST-600 Configuration Guide – DOC. 7383D
TST-600 Main Menu
The main menu displays the current RF ID, RF Channel and battery status and is
also comprised of buttons for RF Setup, Audio Setup, Display Setup,Standby
Timeout, Networking Setup, and Diagnostics. In addition, there are buttons that
provide information about the touch screen and a Save & Exit button. The functions
of each are detailed in the next section of this guide.

Crestron TST-600 5.7” Wireless Touch Screen
Configuration Guide – DOC. 7383D 5.7” Wireless Touch Screen: TST-600
•
3
Configure the TST-600
RF Setup
From the main menu, touch RF Setup to display the “RF Setup” screen.
“RF Setup” Screen
The “RF Setup” screen has Acquired and GW Online indicators to show the status of
the TST-600 and associated gateway. To the right of these is a message display area
used to show the status of acquire processes, an Acquire button used to initiate
acquires and a bar graph showing RF signal strength. Below these are controls for
setting the RF ID, RF Channel, and RF Power. At the bottom of the screen, the
Gateway UID and Gateway Name are displayed.
Before a TST-600 can be used with a Crestron control system, it must first be
acquired by a CEN(I)-ERFGW-POE Extended Range RF Wireless Gateway (sold
separately).
To acquire a TST-600:
1. Use a stylus or other thin tipped object to press ACQUIRE on the
CEN(I)-ERFGW-POE gateway to enter Acquire mode. The accompanying
LED illuminates, indicating the unit is ready to link with the touch screen.
2. Place the TST-600 in Acquire mode by touching Acquire on the “RF
Setup” screen. The screen displays an Acquire in progress message and the
TST-600 is automatically acquired by the gateway within 2 minutes.

5.7” Wireless Touch Screen Crestron TST-600
4
•
5.7” Wireless Touch Screen: TST-600 Configuration Guide – DOC. 7383D
“RF Setup” (Acquire in progress) Screen
3. When the process is complete, the screen displays an Acquire OK message.
Press ACQUIRE on the gateway to exist Acquire mode. The LED turns
off.
“RF Setup” (Acquire OK) Screen
NOTE: Select an RF channel between 12 and 23 for maximum range. Channels 11,
24-26 will result in less range but are available if RF interference requires moving
the RF channel.
NOTE: The RF ID of the unit must match the RF ID specified in the SIMPL
Windows program.
For details, refer to “Appendix A: The RF Spectrum” on page 15 and “Appendix B:
Optimum RF Reception Guidelines” on page 16.
From any of the setup menus, touch to go back to the previous menu.

Crestron TST-600 5.7” Wireless Touch Screen
Configuration Guide – DOC. 7383D 5.7” Wireless Touch Screen: TST-600
•
5
Audio Setup
From the main menu, touch Audio Setup to display the “Audio Setup” screen.
“Audio Setup” Screen
The “Audio Setup” screen provides controls for muting (or unmuting) the audio,
adjusting level for both Master Volume and Media Volume, as well as a control for
playing a test audio file. The Media Volume controls adjust H.264 streaming media
level in relation to the Master Volume controls.
Touch to return to the main menu.
Display Setup
From the main menu, touch Display Setup to enter the “Display Setup” menu.
“Display Setup” Menu
The “Display Setup” menu provides controls for LCD (Screen) Brightness, Key
Backlight Brightness, and On and Off controls for Hard Key Wakes LCD.

5.7” Wireless Touch Screen Crestron TST-600
6
•
5.7” Wireless Touch Screen: TST-600 Configuration Guide – DOC. 7383D
Touch High, Med, & Low Settings to enter the “Display Setup - High, Med, & Low
Settings” screen.
“Display Setup – High, Med, & Low Settings” Screen
The “Display Setup - High, Med, & Low Settings” screen allows setting custom
values for the rapid access Low, Med and High buttons, used to control screen
brightness or key backlight brightness.
Touch to return to the “Display Setup” menu and touch it again to return to
the main menu.
Standby Timeout
From the main menu, touch Standby Timeout to display the “Standby Timeout”
screen.
“Standby Timeout” Screen
The “Standby Timeout” screen provides controls to adjust Standby timeout (from 0
to 120 seconds) and the Power Down timeout (from 0 to 240 seconds), both for when