Crestron TSW-570 User manual

The Crestron® TSW-570, TSW-770, and TSW-1070 are wall mount touch
screens that feature web browsing, Smart Graphics® software and
HTML5 UItechnology, custom-programmable icons, H.265/H.264
streaming video, a Rava® SIPintercom, Wi-Fi® network connectivity, and
PoE+(Power over Ethernet Plus)network power. The touch screens also
provide built-in applications for room scheduling, conferencing, and home
control.
The TSW-570, TSW-770, and TSW-1070 are functionally similar. For
simplicity within this guide, the term "touch screen"is used except where
noted.
In the Box
1TSW-570, TSW-770, or TSW-1070*, WallMount
TouchScreen
Additional Items
# Item (#######)
# Item (#######)
# Item (#######)
TSW-570 Only
# Item (#######)
# Item (#######)
# Item (#######)
# Item (#######)
TSW-770 Only
# Item (#######)
# Item (#######)
# Item (#######)
# Item (#######)
TSW-1070 Only
# Item (#######)
# Item (#######)
# Item (#######)
# Item (#######)
* Refer to the TSW-570-B-S, TSW-770-B-S, and TSW-1070-B-S product pages at
www.crestron.com for a complete list of color variations.
1
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

Install the Mounting Bracket
The TSW-570 uses a different mounting bracket than the TSW-770 or
TSW-1070. The procedures for installing each mounting bracket are
described in the following sections.
Install the TSW-570 Mounting Bracket
The TSW-570 can be mounted into drywall an other surfaces, or it can be
mounted onto a wall stud. When mounted into drywall or other surfaces,
the touch screen protrudes XX in. (XX mm)from the mounting surface.
NOTE: Additional mounting options are possible using the TSW-UMB-70
universal mounting bracket, TSW-UMB-70-PMK preconstruction
mounting kit, TSW-UMB-70-BBI wall mount back box, TSW-570-MSMK
multisurface mounting kit, or TSW-570/770-RMK-1 rack mount kit. For
more information, refer to the product pages at www.crestron.com.
Preconstruction Installations
To install the TSW-570 mounting bracket in preconstruction applications,
use standard drywall nails or screws (not included)to attach the
TSW-UMB-70-PMK mounting bracket to a wall stud.
NOTE:Allow an air gap of at least 12 in. (305 mm)in the wall cavity above
and below the touch screen for heat dissipation.
Postconstruction Installations
To install the TSW-570 mounting bracket in postconstruction
applications:
1. Use the TSW-UMB-70-PMK mounting bracket as a cutout template
by turning the bracket to face the wall, ensuring it is level, and tacking
it the wall temporarily with finishing nails (not included)through the
smaller holes around the cutout opening.
2. Create an opening in the surface by tracing the cutout opening with an
appropriate drywall saw.
3. Loosen the two screws on the TSW-UMB-70 mounting bracket.
4. Install the TSW-UMB-70, bottom side first, into the opening.
2
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

5. Push the rear half of the mounting bracket back so that it is seated
behind the mounting surface completely.
6. Ensure the front of the TSW-UMB-70 is level, and then tighten the two
bracket screws.
Install theTSW-770/TSW-1070 Mounting Bracket
The TSW-770 and TSW-1070 install over a standard 2-gang or 3-gang
U.S. electrical box, a 2-gang European electrical box, or a 2-gang U.K.
electrical box. The touch screen may also be installed into wooden paneling
or furniture with a XX in. (XX mm) high by XX in. (XX mm)wide
rectangular cutout.
When installed, the touch screen protrudes XX in. (XX mm) from the
mounting surface, leaving no visible screws.
NOTES:
lAdditional mounting options are possible using the TSW-UMB-70
universal mounting bracket, TSW-UMB-70-PMK preconstruction
mounting kit, TSW-UMB-70-BBI wall mount back box,
TS-770/1070-MSMK series multisurface mounting kits,
TS-770/1070-MUMK mullion mounting kit, TSW-770/1070-RMB
series retrofit mounting brackets, or TSW-770/1070-RMK series
rack mount kits. For more information, refer to the product pages
at www.crestron.com.
lInstalling the mounting bracket to an electrical box is required only
if one of the mounting solutions above is not used. Refer to the
mounting solution documentation at www.crestron.com/manauls.
To mount the touch screen into an electrical box, use the appropriate
screws (four 6-32x 3/4in. screws, four M3x16mm screws, or two
M3.5x25 mm screws) to attach the mounting bracket to the electrical
box as shown in the following illustrations:
NOTE:For U.S. installations, use a #2 Phillips screwdriver. For
European or U.K. installations, use a #1 Phillips screwdriver.
3
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

lFor U.S. installations, use the four 6-32x 3/4in. screws.
lFor European installations, use the four M3x16mm screws.
lFor U.K. installations(not pictured), use the two M3.5x25 mm screws
to attach the mounting bracket to the electrical box. Insert the screws
through the center openings in the left and right sides of the mounting
bracket.
Install the Security Bracket (Optional)
The included security bracket may be attached to the touch screen so
that it cannot be easily removed from the mounting bracket after
installation. The security bracket snaps into place behind the mounting
bracket so that the touch screen cannot be removed without using the
included metal prong.
Use the two XX x XXin. screws to attach the security bracket to the touch
screen rear housing as shown in the following illustration.
4
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

To remove the touch screen after installation, use the metal prong to
push down on the security bracket tabs as shown in the following
illustration while gently pulling the touch screen away from the mounting
bracket. Connect the Touch Screen
Route all necessary cables through the rear of the mounting bracket, and
then make connections to the side of the touch screen rear housing as
shown in the illustration below.
Observe the following when connecting the touch screen:
lPower and data connection is provided to the touch screen by a single
Ethernet cable. A Crestron PoE (Power over Ethernet) power supply,
such as the PWE-4803RU, or a PoE-capable network switch is
recommended (both not included).
lThe USB ports are used to connect compatible Crestron LED
accessories to the touch screen.
NOTE: The TSW-770 may use either PoE or PoE+ to supply power
to compatible LED accessories over USB; the TSW-1070 must use
only PoE+ to supply power to LED accessories over USB.
lApply power after all connections have been made.
5
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

Mount the Touch Screen
After all connections have been made, push the touch screen gently into
the mounting bracket so that its rear housing is secured within the center
opening within the mounting bracket.
If the touch screen is not level after installation, pull it out of the mounting
bracket and loosen the screws holding the bracket into place. This
procedure allows the mounting bracket to be rotated slightly.
Once the mounting bracket has been repositioned, retighten the screws,
reinstall the touch screen into the bracket, and ensure that the touch
screen is now level.
Configure the Touch Screen
When power is applied for the first time, the following screen is displayed.
The touch screen may take up to two minutes to boot.
6
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

Touch the screen to display the main Setup screen (TSW-1070 shown).
Device settings for the touch screen may be configured using the built-in
setup screens or the web configuration interface. For more information
on configuring the touch screen, refer to the
TSW-570/TSW-770/TSW-1070 Supplemental Guide (Doc.8550) at
www.crestron.com/manuals.
Access the Device Setup Screens
To access the built-in setup screens, place five fingers on the display and
hold for 15 seconds.
Use the setup screens to configure various settings for the touch screen,
including Ethernet setup, IP table setup, audio setup, display setup,
standby timeout, application selection, Wi-Fi network setup, diagnostics,
the Bluetooth™ beacon, and the virtual toolbar.
Access the WebConfiguration Interface
The touch screen provides a web configuration interface that is used to
view and configure various touch screen settings and to select an
application. The interface can be accessed using the touch screen IP
address or the Crestron XiO Cloud™ service.
Touch Screen IPAddress
To access the web configuration interface using the touch screen IP
address:
1. Ensure that the touch screen is connected to the network.
2. Use the Device Discovery tool in Crestron Toolbox™ software to
discover the touch screen and its IP address on the network.
3. Enter the touch screen IP address into a web browser.
Crestron XiOCloud Service
The Crestron XiO Cloud service allows supported Crestron devices across
an enterprise to be managed and configured from one central and secure
location in the cloud. Supported devices are configured to connect to the
service. Use of the service requires a registered Crestron XiOCloud
account.
NOTE:The device may be disconnected from the service by navigating
to the Cloud Services tab in Crestron Toolbox software (Functions >
Device Info >Cloud Services). For details, refer to the Crestron
Toolbox help file.
7
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

To access the web configuration interface using the Crestron XiOCloud
service:
1. Record the MAC address and serial number that are labeled on the
shipping box or rear panel of the device. The MAC address and serial
number are required to add the device to the service.
2. Do either of the following:
lFor existing accounts, access the Crestron XiO Cloud service at
https://portal.crestron.io.
lFor new accounts, register for a Crestron XiO Cloud account at
www.crestron.com/xio-cloud-registration.
3. Claim the device to the service as described in the Crestron XiO Cloud
User Guide (Doc. 8214) at www.crestron.com/manuals.
4. Select the device from the cloud interface to view its settings.
Set the Time Zone
The time zone must be set on the touch screen if it will not be paired with
a control system IPtable.
To set the time zone:
1. Access the web configuration interface using either the touch screen
IP address or the Crestron XiO Cloud service.
2. Select the Settings tab.
3. Navigate to System Setup >Time/Date.
4. Select the time zone where the touch screen will be used from the Time
Zone drop-down menu.
5. Click Save Changes on the top right of the screen.
Visit the Product Pages
Scan the QR code to visit the product page.
TSW-570
www.crestron.com/model/6510812
TSW-770
www.crestron.com/model/6510813
TSW-1070
www.crestron.com/model/6510814
8
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, Crestron XiO Cloud, Rava, and Smart
Graphics are either trademarks or registered trademarks of Crestron Electronics, Inc.
in the United States and/or other countries. Bluetooth is either a trademark or
registered trademark of Bluetooth SIG, Inc. in the United States and/or other
countries. Wi-Fi is either a trademark or registered trademark of Wi-Fi Alliance in the
United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
Doc ID 8552A
(2054672)
02/06/20
9
TSW-570/TSW-770/TSW-1070 QuickStart
5 in., 7 in., and 10.1 in. Wall Mount Touch Screens
PRELIMINARY