Crestron IM-FTCC-B How to use

CrestronIM-FTCC-B
iMediaFlipTopComputerCenter
Operations & Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2006 Crestron Electronics, Inc.

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Contents
iMedia FlipTop Computer Center: IM-FTCC-B 1
Introduction..........................................................................................................1
Features and Functions...........................................................................1
Applications...........................................................................................2
Specifications.........................................................................................4
Physical Description...............................................................................4
Industry Compliance............................................................................10
Setup...................................................................................................................11
Network Wiring ...................................................................................11
IM Wiring ............................................................................................11
Installation............................................................................................13
Hardware Hookup................................................................................17
Operation............................................................................................................19
Problem Solving.................................................................................................20
Troubleshooting ...................................................................................20
Further Inquiries...................................................................................20
Future Updates.....................................................................................20
Appendix A: International Receptacles..............................................................21
Return and Warranty Policies.............................................................................22
Merchandise Returns / Repair Service.................................................22
CRESTRON Limited Warranty ...........................................................22
Operations & Installation Guide – DOC. 6349A Contents •i

Crestron IM-FTCC-B iMedia FlipTop Computer Center
iMedia FlipTop Computer
Center: IM-FTCC-B
Introduction
Features and Functions
 Installs flush in a tabletop surface
 Convenient cable storage
 One AC power pass-through
 One iMedia RJ-45 output connector (on the bottom side)
 Power on/off SELECT button and indicator
 Rotary local volume control
 Lid flips open 180 degrees for easy access
 Includes cable management kit with VGA and audio cables
 Cutout template provided
 Available in both domestic (IM-FTCC-B) and international
(IMI-FTCC-B) models
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •1

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Applications
The IM-FTCC-B/IMI-FTCC-B is part of the Crestron®iMedia line of network
devices, room control systems and signal routing solutions. The line of IM
devices includes receivers and transmitters. Consult the Crestron website for a
complete and current listing of the iMedia product line.
NOTE: Composite video output of the IM-RXV1 and IM-RXV3 will not be
displayed when using the IM-FTCC-B/IMI-FTCC-B.
The iMedia FlipTop Computer Center is designed to install flush in a tabletop
surface to provide a convenient and low profile interface solution. Beneath the
flip-top lid, a recessed compartment contains easy pull-out RGB and audio
cables to facilitate the connection of a single computer source. The cables stow
neatly within the compartment when not in use. Excess cable simply drops out-
of-sight below the box through grommeted holes provided in the bottom plate.
An additional hole is available to accommodate a third-party LAN cable if
needed. A cutout template is included.
NOTE: The IM-FTCC-B and IMI-FTCC-B are not Cresnet®devices.
This device uses iMedia (IM) technology utilizing a single CresCAT-IM cable
to transmit computer RGB and stereo audio signals to a single projector or
plasma display. A typical XGA signal (1024 X 768 pixels at 60 Hz) can be
transmitted up to 84 feet using iMedia, while higher resolutions up to
1600 x 1200 can be handled over shorter distances. Audio is transmitted
digitally at 20-bit, 48 kHz resolution. To facilitate connection of audio, video,
and computer equipment, all media, power and control signals are routed via a
single CresCAT-IM cable for an uncomplicated installation.
The IM-FCC-B is part of a family of compatible iMedia devices, all capable of
working together to put on simple to complex media presentations. The
following diagram shows the interconnections.
2 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Typical Room Installation for Media Presentation (IM-FTCC-B Is shown at Bottom)
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •3

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Specifications
Specifications for the IM-FTCC-B/IMI-FTCC-B are given in the following
table.
IM-FTCC-B/IMI-FTCC-B Specifications
SPECIFICATION DETAILS
Video Formats RGBHV (VGA), RGBS, RGsB
R/G/B: 0 dB (Unity gain, 75 Ohm termination), for
1.0 V p-p max input. Input Impedance 75 Ohms.
RGB Video
Supports videos up to XGA @ 60 Hz vertical rate
with maximum cable length of 84 feet and
maximum compensation at receiver. For higher
pixel resolutions (up to 1600 X 1200 pixels at
60 Hz vertical rate) refer to the chart on page
Resolutions
12.
H and V Sync 5 V p-p max into 1 K Ohm
Computer Associated
Audio
Max. Line level input 2 V RMS
Input Impedance 10 K Ohm
Audio Analog/Digital
conversion 20-bit, 48 kHz
Frequency Response 20 Hz to 20 kHz
Operating Temperature
and Humidity 41º to 104º F (5º to 40º C) 10 to 90% relative humidity (non-condensing)
Dimensions and Weight
(IM-FTCC-B) Width: 6.84 in (17.38 cm)
Height: 4.63 in (11.76 cm) With Lid Closed
Depth: 5.62 in (14.28 cm) Without Mounting
Brackets
Weight: 3.65 lbs (1.66 kg) With Cables
Dimensions and Weight
(IMI-FTCC-B) Width: 8.34 in (21.18 cm)
Height: 5.43 in (13.79 cm) With Lid Closed
Depth: 6.20 in (15.74 cm) Without Mounting
Brackets
Weight: 4.42 lbs (2.01 kg) With Cables
International Adaptors for
IMI-FTCC-B Models Refer to Appendix on page 21.
Physical Description
Beneath the flip-top lid, a recessed compartment contains RGB and audio cables
to facilitate the connection of a single computer source. The recessed
compartment also contains the AC outlet and the SELECT button. Refer to the
following physical views.
4 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
IM-FTCC-B Open View
Open View (IM-FTCC-B) Open View (IMI-FTCC-B)
SELECT
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •5

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Physical Dimensions – Top View (IM-FTCC-B) Physical Dimensions – Top View (IMI-FTCC-B)
5.62 in
(14.28 cm)
6.84 in
(17.38 cm)
6.20 in
(15.74 cm)
8.34 in
(21.18 cm)
Physical Dimensions – Front View (IM-FTCC-B) Physical Dimensions – Front View (IMI-FTCC-B)
Rests on
Table
Surface
0.14 in
(0.36 cm)
4.49 in
(11.41 cm)
5.36 in
(13.62 cm)
Power Cord
6.86 in
(17.42 cm)
0.14 in
(0.36 cm)
5.29 in
(13.44 cm)
Physical Dimensions – Side View (IM-FTCC-B) Physical Dimensions – Side View (IMI-FTCC-B)
4.19 in
(10.65 cm)
Power Cord 4.77 in
(12.11 cm)
6 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Front Face View (IM-FTCC-B) Front Face View (IMI-FTCC-B)
SELECT
1 2 3 1 2 3
Bottom View (IM-FTCC-B) Bottom View (IMI-FTCC-B)
4 5 6 7 8 4 5 6 7 8
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •7

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Controls, Connectors & Indicators
# CONNECTORS,
CONTROLS &
INDICATORS
DESCRIPTION
125 VAC, 50 – 60 Hz., 10 amperes. This 3-prong
grounded AC input socket is connected to a line
cord located on the bottom side.
1
250 V max, 50 to 60 Hz, 10 amperes.
European, Australian, Italian, United Kingdom
and French versions available. Refer to
“Appendix A: International Receptacles” on page
21.
2
SELECT
Selector button and indicator light. Indicator light
signals the FlipTop Computer Center selected
for control. Button selects inputs, including
projector power on. A blinking light indicates
control is changing from one FlipTop Computer
Center to another. Holding the selector button in
for five seconds powers down the unit.
Rotary local volume control; adjusting this knob
sets the audio level for the local input.
3 VOLUME
Continued on the following page
8 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Controls, Connectors & Indicators (continued)
# CONNECTORS,
CONTROLS &
INDICATORS
DESCRIPTION
4 This is a grounded AC socket.
125 VAC at 60 Hz. Connect the six-foot (183 cm)
grounded AC line cord to supply AC power to the
outlet on the topside of the IM-FTCC-B.
This is a grounded AC socket.
250 V, 50-60 Hz at 10 A max. The IMI-FTCC-B is
equipped with a standard IEC-320 electrical
appliance coupler. The IEC (International
Electrotechnical Commission) is the international
standards and conformity assessment body for all
fields of electrotechnology.
5 AUDIO
The 3.5 mm computer audio connector provides an
unbalanced stereo line-level audio input.
Maximum input level 2 VRMS
Input impedance 10k Ohms
IM This eight-pin RJ-45 transport port allows
connection of the iMedia cable. It carries audio and
video signals over CresCAT-IM cable to an iMedia
receiver (IM-RX1 or IM-RX3). For more information
on iMedia cable length refer to the chart on page
6
.12
7 COMPUTER PIN 1
PIN 6PIN 15
This female DB15HD connector is used for
connecting a computer’s RGB video output to the
display device. A corresponding 3.5mm mini-jack is
provided for the computer sound card output.
Maximum input voltage 1.0 Vp-p (R/G/B), 5.0 Vp-p
(H/V)
Input Impedance 75 Ohms (R/G/B), 1 k Ohms
(H/V)
Refer to the following table for RGB DB15HD pin-
assignments.
PIN FUNCTION PIN FUNCTION
1 Red Video 9 No Connect
2 Green Video 10 Ground
3 Blue Video 11 No Connect
4 Reserved 12 Monitor
Sense 1
5 Ground 13 Horizontal
Sync
6 Red Ground 14 Vertical Sync
7 Green
Ground 15 Monitor Sense 2
8 Blue Ground
8 Lug for grounding your equipment.
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •9

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Industry Compliance
As of the date of manufacture, the IM-FTCC-B/IMI-FTCC-B has been tested
and found to comply with specifications for CE marking and standards per EMC
and Radiocommunications Compliance Labelling.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
10 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Setup
Network Wiring
CAUTION: In order to ensure optimum performance over the full range of your
installation topology, Crestron Certified Wire, and only Crestron Certified Wire,
should be used. Failure to do so, may incur additional charges if support is
required to identify performance deficiencies as a result of using improper wire.
CAUTION: Use only Crestron power supplies for Crestron equipment. Failure
to do so could cause equipment damage or void the Crestron warranty.
IM Wiring
Using a proprietary signal routing solution, RGBHV, audio, power and control
signals are all transported using a single cable solution called iMedia.
The iMedia transport system port is capable of managing computer RGB and
audio signals simultaneously through one CresCAT-IM cable, simplifying
installations.
Routing CresCAT-IM cable (low-skew CAT5e) is less expensive and a much
simpler solution for the wiring of iMedia systems than routing multi-colored, multi-
conductor coax cable. All Crestron products using the iMedia transport system are
capable of sending and receiving iMedia signals via CresCAT-IM cable. Installation
of any iMedia device is as simple as installing one iMedia cable from output to
input. Installations are affordable, and fast.
Quantity and Packaging
 CRESCAT-IM-P-B500 is a low-skew CAT5e cable, plenum-rated,
available in a 500 ft box
 CRESCAT-IM-P-SP500is a low-skew CAT5e cable, plenum-rated,
available in a 500 ft spool
 CRESCAT-IM-P-SP1000 is a low-skew CAT5e cable, plenum-rated,
available is a 1000 ft spool
For more information on CresCAT and other wire products, visit the Crestron
website (www.crestron.com/features/wire).
Pin Assignments
The pin assignment is based on the EIA/TIA 568B RJ-45 Jack standard.
Power is supplied to the IM transmitters via the audio circuit.
To determine which pin is number 1, hold the cable so that the end of the eight
pin modular jack is facing you, with clip down and copper side up. When
looking down at the copper connections, pin 1 is on the far right.
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •11

iMedia FlipTop Computer Center Crestron IM-FTCC-B
iMedia Pin Assignment
RJ-45 Male Connector RJ-45
Pin
Number
Wire Colors iMedia
Assignment
RGB & Audio
NOTE: Power is supplied to pins 4 and 5 from the IM receivers.
Signal Selection
The RGB signal connected to the IM transmitter is delivered to the display
device (e.g., projector) via the RGBHV output of an IM receiver. Each IM
transmitter possesses a SELECT button, which activates that input. The receiver
automatically routes the last activated input to the RGB output and deactivates
any prior selection. In addition, the display's power and input selection
commands can be controlled via the IR or COM port.
Video Resolution and Cable Length
The receiver can accomplish frequency compensation on each input to achieve
correct operation. This compensation scheme is effective for CresCAT-IM
cables as long as the maximum skew of 15 ns per 100 m is not exceeded.
NOTE: For proper operations and performance of every iMedia system, always
use CresCAT-IM cable.
Maximum Resolution and Cable Length
RESOLUTION REFRESH
RATE
(HZ)
PIXEL
RATE
(MHZ)
PIXEL
TIME
(NS)
MAX
LENGTH
(FEET)
VGA 60 25.18 39.7 218.5
(640 X 480) 72 31.50 31.7 174.6
85 36.00 27.8 152.8
SVGA 56 36.00 27.8 152.8
(800 X 600) 72 50.00 20.0 110.0
85 56.25 17.8 97.8
XGA 60 65.00 15.4 84.6
(1024 X 768) 70 75.00 13.3 73.3
85 94.50 10.6 58.2
SXGA 60 108.00 9.3 50.9
(1280 X 1024) 75 135.00 7.4 40.7
85 157.50 6.3 34.9
UXGA 60 162.00 6.2 34.0
(1600 X 1200) 70 189.00 5.3 29.1
85 229.50 4.4 24.0
1 White/Orange - RGB Red2 Orange + RGB Red
3 White/Green - RGB Green
4 Blue + Audio/Power
5 White/Blue - Audio/Power
6 Green + RGB Green
7 White/Brown - RGB Blue
Pin 1 8 Brown + RGB Blue
12 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Installation
Cable Management Kit
The IM-FTCC-B and IMI-FTCC-B are shipped with a cable management kit
that includes a cable management plate, a 6-foot VGA cable and a 6-foot audio
cable.
Tools Required
• Phillips screwdriver
• Small flat-blade screwdriver (for connecting the VGA cable)
Parts Supplied with Cable Management Kit
PART DESCRIPTION QUANTITY
Small Cable Bushing, 5/16 inch ID, 0.5 inch OD 2
Large cable Bushing, 0.55 inch ID, 0.80 inch OD 1
Cable Support Plate 1
4-40 ¼ inch Phillips Head Screws 4
Computer RGB Cable, VGA to VGA, 6 ft long 1
Computer Audio Cable, 3.5 mm Stereo, 6 ft long 1
Tie Wraps 3
The cable support plate must be installed before mounting the IM-FTCC-B or
IMI-FTCC-B to a surface. The cables are looped through the cable support plate.
1. Place the bushings on the cables (three bushings supplied). Use the
large bushing for the VGA cable.
2. Thread the cables through the appropriate slot on the plate.
3. Snap the bushings into the plate slots.
4. Feed all the excess cable through the opening.
5. Attach the plate using the four #4 x 1/4 black screws.
6. Connect the cables to the appropriate connector on the bottom of the
IM-FTCC-B/IMI-FTCC-B.
7. The cables may be secured to the bottom bar using tie wraps.
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •13

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Cable Plate Installation (IM-FTCC-B Shown)
Cable Loops Through the Cable Plate (IM-FTCC-B Shown)
NOTE: Ensure that the cables have sufficient clearance to enable smooth
movement. Allow approximately 40 inches (102 cm) from the top surface of the
FlipTop box mounting to surface.
Mounting to Surface
The IM-FTCC-B/IMI-FTCC-B is designed to mount in a horizontal surface,
such as a desk top, lectern, or podium. The following diagram illustrates the
required opening size to accommodate the IM-FTCC-B/IMI-FTCC-B. Use the
supplied template to make the cutout.
14 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A

Crestron IM-FTCC-B iMedia FlipTop Computer Center
Cutout Dimensions for IM-FTCC-B (4007291)
6.31 in
(16.02 cm)
4.625 in
(11.75 cm) Radius
0.125 in
(0.318 cm) Max
Cutout Dimensions for IMI-FTCC-B (4007909)
Radius
0.125 in
(0.318 cm)
5.12 in
(13.005 cm)
7.78 in
(19.761 cm)
NOTE: Before inserting the IM-FTCC-B or the IMI-FTCC-B in the mounting
hole, ensure that all required cables have been installed.
Mounting Parts Supplied with the IM-FTCC-B/IMI-FTCC-B
PART DESCRIPTION QUANTITY
Screw #6-32, Pan Head, Phillips 8
Screw #10-32, Pan Head, Phillips 4
Mounting Bracket 2
1. Install the eight supplied #6-32 screws, but do not tighten (four on the
front side and four on the rear side). These will be used to secure the
front and rear mounting brackets.
2. Position the IM-FTCC-B/IMI-FTCC-B in the mounting hole.
Operations & Installation Guide – DOC. 6349A iMedia FlipTop Computer Center: IM-FTCC-B •15

iMedia FlipTop Computer Center Crestron IM-FTCC-B
Mounting Bracket Screw Locations
#6-32 Screws
#6-32 Screws
Surface
Cutout
3. Install the four #10-32 screws in the mounting brackets (two screws per
bracket). Refer to the following diagram.
4. Slide the mounting brackets over the #6-32 screws and tighten the
#6-32 screws.
Mounting Bracket Installation
5. Turn the four #10 screws equally until they contact the underside of the
mounting surface.
NOTE: Do not over-tighten the #10 screws as this may damage the surface
and/or the unit.
16 •iMedia FlipTop Computer Center: IM-FTCC-B Operations & Installation Guide - DOC. 6349A