Crestron DM-TX-4KZ-202-C User manual

The Crestron® DM-TX-4KZ-202-C and DM-TX-4KZ-302-C provide a
versatile interface for ultra high-definition AV sources as part of a
complete Crestron DigitalMedia™ system. The devices function as DM
8G+® transmitters and switchers, and also provide control module
functionality.
In the Box
1DM-TX-4KZ-202-C or DM-TX-4KZ-302-C, DigitalMedia 8G+®
4K60 4:4:4 HDR Transmitters
Additional Items
1 Connector, 2-Pin (2003574)
1 Connector, 5-Pin (2003577)
Install the Transmitter
NOTE:
This unit is for indoor use only. It is not intended for outdoor use.
Cet appareil est réservé à une utilisation en intérieur. Il n’est pas
destiné à une utilisation en extérieur.
The DM-TX-4KZ-202-C and DM-TX-4KZ-302-C can be mounted onto a
flat surface or onto a rack rail.
Mount onto a Flat Surface
Using four mounting screws (not included), mount the device onto a flat
surface such as a wall or a ceiling.
1
DM-TX-4KZ-202-C and DM-TX-4KZ-302-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Transmitters

Mount onto a Rack Rail
The DM-TX-4KZ-202-C or DM-TX-4KZ-302-C can be mounted onto a
front or rear rack rail. To mount the device:
1. Position either of the mounting flanges so that the holes align with the
holes in the rack rail.
2. Secure the device to the rack rail using two rack mount screws (not
included).
Connect the Transmitter
Connect the device as required for the application.
NOTE: The DM OUT port is a PoDM+ powered device (PD) port and is
also compatible with HDBaseT® PoE+.
lIn order for the port to receive PoDM+, the port requires
connection to a DigitalMedia™ switcher or other DigitalMedia
equipment that has a corresponding PoDM+ power sourcing
equipment (PSE) port.
lIn order for the port to receive HDBaseT PoE+, the port requires
connection to equipment that has a corresponding HDBaseT PoE+
PSE port.
Wiring that is connected to a PoDM+ or HDBaseT PoE+ PSE port is
for intrabuilding use only.
PoDM+, HDBaseT PoE+, or the optional PW-2412WU power pack (sold
separately) can be used to power the devices.
2
DM-TX-4KZ-202-C and DM-TX-4KZ-302-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Transmitters

Left and Right Side Connections (DM-TX-4KZ-302-C Shown)
3
DM-TX-4KZ-202-C and DM-TX-4KZ-302-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Transmitters

For information about DM OUT connector pin assignments, refer to the
following illustration and table.
DM OUT Wiring
Pin Number Wire Color
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
Upgrade the Firmware
Before using the device, upgrade the firmware. The latest firmware can be
downloaded from the DM-TX-4KZ-202-C and DM-TX-4KZ-302-C
product page on the Crestron website (www.crestron.com).
Determine the IP Address
The physical configuration of the DM-TX-4KZ-202-C or
DM-TX-4KZ-302-C within a DigitalMedia 8G+ system determines how the
IP address of the transmitter is set:
lIf the transmitter is connected to a DigitalMedia switcher, the IP
address is configured by the switcher automatically. You do not need
to set the IP address.
lIf the transmitter is connected directly to a DigitalMedia 8G+ receiver
(commonly referred to as a standalone configuration in which no
DigitalMedia switcher is used), the IP address of the transmitter is
assigned using DHCP (Dynamic Host Configuration Protocol) by
default. If you wish to assign a static IP address, do either of the
following:
oTo assign the default static IP address of the transmitter, hold
down the SETUP button while the unit boots up. The default static
IP address, which is 192.168.1.251 for the DM-TX-4KZ-202-C and
192.168.1.252 for the DM-TX-4KZ-302-C, overwrites the current
setting.
oTo manually set a static IP address other than the default address,
use the Crestron Toolbox™ software.
4
DM-TX-4KZ-202-C and DM-TX-4KZ-302-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Transmitters

Visit the Product Page
Scan the QR code to visit the product page.
DM-TX-4KZ-202-C
www.crestron.com/model/6508079
DM-TX-4KZ-302-C
www.crestron.com/model/6508078
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Doc. 7939B
04/15/20
5
DM-TX-4KZ-202-C and DM-TX-4KZ-302-C QuickStart
DigitalMedia 8G+® 4K60 4:4:4 HDR Transmitters