CrimeStopper CS-5601 User manual

CS-5601
4 WINDOW CONTROL MODULE
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION:
CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, and operating your system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number
below.
*IMPORTANT INFORMATION:
This system does not affect the operation of the factory power window switches. This is an ADD-ON
module to an Alarm, Remote Start, or Keyless Entry system. It is designed for medium to high current
window motors. It can roll 4 windows UP or DOWN, or 2 windows UP and DOWN. Each window circuit
activates in sequence, oneat a time. This minimizes the current draw on the vehicle battery.
This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,
we suggest that you READ THIS MANUAL before beginning your installation. The information contained in
this manual is provided as a GENERAL GUIDLINE and it may differ from your vehicle! If you are not confident
with performing the installation steps as required by this system, we suggest seeking professional installation.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
[phone]
REV -9/3/2004

TABLE OF CONTENTS
•Pre-Installation & Component Mounting………………..…….……………………………………………2-3
•Wiring …………..………………………………………………………………………………………….…….3-4
•4 Windows UP.…..………………………………………….……………….………..……………….…..……..5
•2 Windows UP and DOWN..………………….…………………………………………………………………6
•Vehicles with Normally Open Power windows……………..………….……………………………………7
•Testing and Adjusting Window Shut Off Current…………………..………………………………………8
PRE-INSTALLATION CONSIDERATIONS
To ease installation, we suggest that you READ THIS MANUAL before beginning your installation.
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).
PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed.
These components include: the module itself, valet/program button and possible relays. Allow enough wire to
create a service loop with strain relief, should servicing be required.
DAMAGE resulting from incorrect installation or failure to follow guidelines stated in this book will not be
covered under warranty and subject to repair or replacement charges.
USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer
systems.
ADDITIONAL PARTS, extra relays (Part #CS-402A) for converting normally open or normally powered
window switches to normally grounded.
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.
REMOVE MAIN SYSTEM FUSE (S)before jump starting the vehicle or charging the vehicles battery.
2

COMPONENT MOUNTING
CONTROL MODULE: Locate the module under dash as high as possible, away from moving parts. Driver’s
Side usually provides an easy location for the majority of the wiring connections.
WARNING: Module isn’t water proof. Don’t Install CS-5601 Module inside vehicle door.
If the module gets water damaged, the vehicle windows could stop working.
WIRING
8Position Connector Plug –Small Wires
1 -GRAY: Negative roll trigger for Circuit #1 and #2.
Circuit #1and #2are controlled by LOOP 1-USE ONLY ONE.
2 -GRAY/WHITE: Positive roll trigger for Circuit #1 and #2.
3 -BLACK: SYSTEM CHASSIS GROUND:This wire must be connected to chassis metal of vehicle.
Scrape away any paint or dirt from the connection point to ensure a good connection.
4 -GREEN: (-) 300 milliamps Negative output though out operation of any 4 circuits
5 -YELLOW: (+) 300 milliamps Positive output through out operation of any 4 circuits
6 -BLUE: Negative roll trigger forCircuit #3 and #4.
Circuit #3and #4are controlled by LOOP 2 -USE ONLY ONE.
7 -BLUE/RED:Positive roll trigger for Circuit #3 and #4.
8 -PINK: Connect to an ignition wire that shows +12 Volts when the key in both “On” and “Start” positions.
This wire prevents the module from activating the windows while driving the vehicle.
3

WIRING
2 JUMPER LOOPS
LOOP 1: Circuit #1 and #2
•CUT:Constant or Latched (starter kill), Triggerfor window circuit #1 and #2.
•CONNECTED: Momentary Pulse (2nd channel), Trigger for window circuit #1 and #2.
LOOP 2:Circuit #3 and #4
•CUT:Constant or Latched (starter kill), Triggerfor window circuit #3 and #4.
•CONNECTED: Momentary Pulse (2nd channel), Trigger for window circuit #3 and #4.
9 Position Connector Plug –Large Wires
1 -RED WIRE: (+) 12 Volt Power Source (30 amp fuse) Connect to +12 Volt source with supplied fuse &
holder. Recommended location for this connection is at a main power distribution terminal or the vehicle
battery positive terminal.
2 -BLACK WIRE: (+) Switch side of window circuit #1. Normally Closed in reference to “BLACK” wire.
Circuit #1
3 -BLACK/WHITE WIRE: (+)12 volt output tomotor side of window circuit #1.
4 -GRAY WIRE: Switch side of window circuit #2. Normally Closed in reference to “GRAY/WIRE” wire.
Circuit #2
5 -GRAY/WHITE WIRE: (+)12 volt output tomotor side of window circuit #2.
6 -BROWN: Switch side of window circuit #3. Normally Closed in reference to “BROWN/WIRE” wire.
Circuit #3
7 -BROWN/WHITE: (+)12 volt output tomotor side of window circuit #3
8 -BLUE WIRE: Switch side of window circuit #4. Normally Closed in reference to “BLUE/WIRE” wire.
Circuit #4
9 -BLUE/WHITE WIRE: (+)12 volt output to motor side of window circuit #4
4

5
Left
Front
Circuit #1
Righ
t Front
Circuit #2
Left R
ear
Circuit #3
Right Rear
Circuit #4

Circuit #1 and #2 is used to roll widows up.
Circuit #3 and #4 is used to roll windows down.
6
Ci
rcuit #2
Circuit #1
Circuit #3
Circuit #4

This diagram is used on vehicles with window circuits that:
1. Switch ground to roll the windows up or down.
2. Switch both power and ground to roll the windows up or down.
3. Have a One Touch window switch to roll up or down or Express Down Toll Booth.
Circuit #1
**NOTE**
See page3
for 8 Pin
Plug Wiring
7

ADJSUSTING WINDOW SHUT OFF CURRENT
VR-2: WindowCircuit #3 and #4 VR-1: WindowCircuit #1 and #2
Turn clockwise to increase High Current shut off limit.
•Min = 10 Amps
•Max = 30 Amps
www.crimestopper.com
[email protected]
Phone [phone]
FAX [phone]
© 2003 Crimestopper Security Products
CS
-
5601
Rear Access Door
VR
-
1
VR
-
2
ONLINE TECHNICAL SUPPORT
www.crimestopper.com/techweb03.html