Crosley CO7147 User manual

Outdoor Wicker Corner Chair
CO7147

2
PART LIST
A B CD
FGH
Arm
1 PC
Panel Back
1 PC
Panel Seat Panel
1 PC
Front Panel
1 PC
Cover of Seat
Cushion *
1 PC
HARDWARE LIST
#1 #2 #3 #4 #5
#6 #7
Short Bolt
4 PCS
Medium Bolt
4 PCS
Long Bolt
6 PCS
Nut
10 PCS
Washer
24 PCS
Wrench
1 PC
Allen Key
1 PC
M6*30mm M6*40mm M6*50mm
EXTRA HARDWARE LIST
M6mm M6mm
M6mm M6mm
E
Side Panel
1 PC
Short Bolt
1 PC
Medium Bo
1 PC
lt Long Bo
2 PCS
lt Nut
2 PCS
Washer
3 PCS
M6*30mm M6*40mm M6*50mm M6mm M6mm
#8
Adjustable
Leveler
4 PCS
M6mm
IJ
K
Core of Seat
Cushion
1 PC
Cover of Side
Cushion *
1 PC
Core of Side
Cushion
1 PC
#1 #2 #3 #4 #5
Cover of Back
Cushion *
1 PC
Core of Back
Cushion
1 PC
*Please note cushion covers will ship separately.
#9
Plastic Clip
2 PCS

3
#2 x2
#5 x4
#4
#6 x1
x2
#7 x1
#7
#2
#5
#5
#4
#6
#3 x4
#5 x8
#4
#6 x1
x4
#7 x1
#7
#3
#5
#5
#4
#6
Step 1.
Attach back panel (part B) to arm panel (part A) using medium bolts(part #2),
washers (part #5),nuts(part #4),wrench(part #6) and allen key (part #7).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
Lay arm panel (part A) down on a .soft flat surface, such as carpet, as shown below
Step 2.
long bolts(part #3) , washers (part #5) ,nuts (part #4),wrench (part #6) and allen
key (part #7).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
Attach seat panel (part C) to arm panel (part A) and back panel (part B) using

4
#1 x1
#5 x5
#4
#6 x1
x2
#7 x1
#3 x2
#1 x3
#5 x7
#4
#6 x1
x2
#7 x1
#2 x2
#7
#1
#5
#7
#3
#5
#5
#4
#6
Step 3.
short bolts (part #1), long bolts (part #3),washers (part #5) ,nuts (part #4),
wrench (part #6) and allen key (part #7).
NOTE:Please do not fully tighten bolts until unit is fully assembled.
Attach front panel (part D) to arm panel (part A) and seat panel (part C) using
#7
#1
#5
#5
#4
#6 #7
#2
#5
Step 4.
,medium bolts (part #2),washers (part #5) ,nuts (part #4) ,wrench (part #6)and
allen key (part #7).
NOTE: Please fully tighten all bolts at this time.
Attach side panel (part E) to assembled unit (parts B ,C&D) using short bolts (part #1)

5
#8
#8
Step 5.
the bottom of the chair where shown.
Screw adjustable levelers (part #8) to desired position in the pre-drilled holes on
KJ
Step 6.Insert core of seat cushion ( ) into cover of seat cushion ( F).
Insert core of back cushion (part I) into cover of back cushion (part H).
lnsert core of side cushion (part K) into cover of side cushion (part J).
part G part
GF
IH

Step 7.Carefully turn the assembled chair upright and add cushions as shown below.
6
Step 8.Use plastic clips (part #9) to secure additional units together as shown.
#9