CRU Dataport RJR110 Ultra320 User manual

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
RJR110 Ultra320 Install Guide
Removable SCSI Ultra320 Drive Enclosures
Note: For applications requiring frequent drive swapping or
replacement, CRU-DataPort recommends the rugged DataPort or
Data Express removable enclosures for high insertion environments.
Front Panel
Unit ID Number Indicator: This LED displays the SCSI ID of the
SCSI drive carrier.
Key Lock/Drive Power Switch: The keylock/drive power
switch performs three functions. The key switch assures proper
seating of the drive carrier within the receiving frame, turns
power to the drive carrier ON and OFF, and prevents unauthorized
removal or installation of the carrier. For the computer to access
data on the disk drive, the key must be turned counterclockwise
to the locked position.
LEDs:
Power - Steady glow indicates power ON.
Drive Activity- Steady glow indicates that drive is inserted
and ready for access. Flashing indicates drive is being ac-
cessed.
Fan - Green indicates normal fan operation. Red indicates fan failure.
OverTemp - Flashing red indicates overtemperature condi-
tions (default is 60° C). Audible alarm will also sound.
Reset Switch: This will reset OverTemp LED back to Green, as
well as turn off audible alarm.
Carrier Fan: Front-mounted carrier fan provides enhanced heat
dissipation (4.7 CFM).
Rear Panel
DC Power Connector: Uses a standard 4-pin DC Power Connec-
tor to accept DC power.
I/O Connector: The input/output connector provides a standard
interface for all Ultra320 signals.
Cooling Fan: Receiving frame fan provides enhanced heat
dissipation (4.7 CFM).
Unit ID Select Switch: (See Figure 2) Allows user to select the ID
number of the disk drive. Refer to table below for Unit ID hex refer-
ence.
Installation
NOTES: A #1 and #2 Phillips screwdriver will be required
for this procedure.
RJR110 supports implementations with a maximum of 2 drives per
channel.
Power
LED
Drive
Activity
LED
Carrier
Handle
Key Lock
Figure 1: Front Panel
OverTemp
LED
7-Segment
Display
Reset
Switch
Fan
LEDFan

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Product Warranty
CRU-DataPort (CRU) warrants the RhinoJR RJR110 to be free of
significant defects in material and workmanship for a period of
two years from the original date of purchase. CRU’s warranty is
nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warranties.
CRU expressly disclaims all other warranties, including but not limited
to, the implied warranties of merchantability and fitness for a particu-
lar purpose and non-infringement of third-party rights with respect to
the documentation and hardware. No CRU dealer, agent or employee
is authorized to make any modification, extension, or addition to this
warranty. In no event will CRU or its suppliers be liable for any costs of
procurement of substitute products or services, lost profits, loss of in-
formation or data, computer malfunction, or any other special, indirect,
consequential, or incidental damages arising in any way out of the sale
of, use of, or inability to use any CRU product or service, even if CRU
has been advised of the possibility of such damages. In no case shall
CRU’s liability exceed the actual money paid for the products at issue.
CRU reserves the right to make modifications and additions to this
product without notice or taking on additional liability.
Certification
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FCC Certification
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received;
including interference that may cause undesired operation.
Register your product at www.CRU-DataPort.com.
A8-110-0001 Rev. 2.1
68-Pin SCSI Model
1. Remove cover from the carrier by turning screw clockwise. Slide the
cover off carrier (Figure 3).
2. Carefully insert drive (not included) into the carrier. Slide the drive
towards the rear of the carrier so that the drive connectors can mate
with the carrier connectors. Once the drive and carrier are mated, turn
the drive/carrier assembly over.
3. Bottom-mount the drive into the carrier with four (4) Phillips screws
(Figure 4). Reinstall cover onto the carrier.
Secure the cover by turning the screw counterclockwise a few rotations
only (too many rotations will remove the screw).
80-Pin SCA SCSI Model
1. Remove cover from the carrier by turning screw clockwise. Slide the
cover off carrier (Figure 3).
2. Carefully insert drive (not included) into the carrier. Turn the drive/car-
rier assembly over.
3. Bottom-mount the drive into the carrier with four (4) Phillips screws
(Figure 4). Reinstall cover onto the carrier.
Figure 3: Cover Removal
Turn Screw
Clockwise to
Remove
Slide Cover
Off
1 2
Figure 4: Installing a
Drive into the Carrier
Bottom-Mount
Drive
Insert 80-Pin SCA SCSI Drive
(not included)
Insert 68-Pin SCA
SCSI Drive (not
included)
Bottom-Mount
Drive
68-Pin SCSI
Drive Carrier
80-Pin SCA
SCSI Drive
Carrier
Figure 2: Rear Panel
DC Power
Connector
I/O Connector
Unit ID Select
Switch
Cooling Fan