CRU Dataport Data Express DE275 User manual

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Data Express DE275 SAS/SATA Install Guide
Removable SAS/SATA Drive Enclosure
Frame Installation
For SATA operation connect a SATA data cable to the SATA/SAS
host 1 connector.
For SAS operation connect a SATA/SAS data cable to either
SATA/SAS Host 1 or SAS Host 2 connector.
For dual host capabilities connect SATA/SAS data cable to SATA/
SAS Host 1 and SAS Host 2.
Connect SATA power or ATX power to the power connectors on
the back of the DE275. The DE275 will support either ATX or
SATA power.
Slide the frame into an available drive bay and secure the frame.
Drive Installation
1. Carefully insert the drive into the carrier. Slide the drive
towards the Drive Carrier Board, so that the I/O connector on
the drive mates with the connector on the Drive Carrier Board.
Turn the drive/carrier assembly over.
2. Fasten the drive into place with the four provided #6-32 Phillips
Under Cut Flat Hd. Screws. Some drives may require minor
adjustment, to position the drive before securing into carrier
with screws.
3. Install the provided drive cover. Insert the front end of the cover
first and then slide the cover towards the rear of the carrier.
Secure drive cover with the two provided #4-40 Phillips Under
Cut Flat Hd. Screws.
The DE275 SAS/SATA enclosure is designed to incorporate the rug-
ged security of the DE200 with the low profile size of the DE75. The
DE275 includes two thumb screws for even greater stability. The 1”
low profile design of the DE275 minimizes the space required for
installation.
Note: CRU recommends that the DE275 carrier not be used in
DE75 frames, nor should DE75 carriers be used in the DE275
frame. While the DE275 and the DE75 are physically the same
CRU does not intend for the product lines to be interchanged.
Figure 1: Receiving Frame Board (rear view)
Package Contents
1 - DE275 carrier assembly
1 - DE275 frame assembly
1 - Key set
1 - Alignment tool
2 - 4-40 x 1/8” Flathead screws (carrier cover)
4 - 6-32 x 1/4” Flathead screws (drive mounting)
4 - M3 x 6mm Trusshead screws (frame mounting)
Receiving Frame Board
Factory-Installed Jumper (Pins 15 & 17) – Factory-installed
jumper. DO NOT REMOVE!
Remote Activity LED (RLED) – These pins provide a remote
LED device activity indicator (Pin 13=Cathode, Pin 14-Anode).
Frame Data Connectivity – For SATA operation the SATA data
cable must be connected to the SAS/SATA Host 1 Connector.
SATA hard drives do not support the SAS Host 2 Connector. SAS
hard drives can use either SAS Host 1 Connector or SAS Host 2
Connector. The DE275 supports the SAS dual host feature for fail
over protection.

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Figure 3: Unit ID Select Switch Location
NOTE: The lock on the Data Express serves as a power
switch. It must be engaged (turned counterclockwise) for the
Data Express to power up and function properly.
Limited Product Warranty
CRU-DataPort (CRU) warrants the Data Express DE275 to be free of sig-
nificant defects in material and workmanship for a period of five years
from the original date of purchase. CRU’s warranty is nontransferable
and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warran-
ties. CRU expressly disclaims all other warranties, including but not
limited to, the implied warranties of merchantability and fitness for a
particular purpose and non-infringement of third-party rights with re-
spect to the documentation and hardware. No CRU dealer, agent or
employee is authorized to make any modification, extension, or ad-
dition to this warranty. In no event will CRU or its suppliers be liable
for any costs of procurement of substitute products or services, lost
profits, loss of information or data, computer malfunction, or any other
special, indirect, consequential, or incidental damages arising in any
way out of the sale of, use of, or inability to use any CRU product or
service, even if CRU has been advised of the possibility of such dam-
ages. In no case shall CRU’s liability exceed the actual money paid for
the products at issue. CRU reserves the right to make modifications and
additions to this product without notice or taking on additional liability.
Register your product at www.CRU-DataPort.com.
A7-275-0001 Rev. 2.0
Unit ID Select Switch Settings
Note: The unit ID number display is for ID display purposes
only.
The following table lists the unit ID select switch settings.
Table 1: Unit ID Hex Reference
Selecting the Unit ID Number: Use the alignment tool (pro-
vided) to select the ID number of the disk drive.
Alignment Tool
Unit ID Select Switch
Figure 2: Drive Installation Overview
Drive Cover
(provided)
SATA/SAS Drive
(not included)
Drive Carrier
Board
Drive Carrier