Crux RVCMT-69 User manual

-Activates Reverse camera input.
-Adds three A/V Inputs.
-On-screen display setup.
-Switch the video sources via the OE buttons.
MASERATI
2008 –Up
Gran Turismo
1 / 6
Rev.120116

Unplug OEM LVDS cable from the OEM monitor (which is connected to the Command box) and plug
it into the LVDS INPUT of the LVDS Controller box.
Connect the LVDS cable supplied in the kit to the LVDS OUT of the RVCMT-69 and to the LVDS IN of
the LVDS Controller box.
Connect the LCD cable supplied in the kit to the LVDS OUT of the LVDS controller box an into the
OEM monitor.
Connecting the CAN Wires
1. Tap CAN HIGH (Brown/Green) from the Power harness to the CAN HIGH (Black/Pink) wire on the Command.
2. Tap CAN LOW(Green) from the Power harness to the CAN LOW (White/Pink) wire on the Command.
1
2
3
2 / 6
Rev.120116

DIP Switch Settings
Disconnect power to the interface before setting the DIP switches.
DIP#
Function
Selection
1
RGB INPUT MUTE
ON : Skip RGB Mode
OFF : RGB Display
2
A/V 1 MUTE
ON : Skip A/V 1
OFF : A/V1 Display
3
A/V 2 MUTE
ON : Skip A/V 2
OFF : A/V2 Display
4
A/V 3 MUTE
ON : Skip A/V 3
OFF : A/V3 Display
5
Not Used
6
Not Used
7
Rear Mode
ON : Aftermarket Rear Camera
OFF : OEM Rear Camera
8
Not Used
Remote Control Functions
Function
POWER & PIP
No Function
MENU
Activate OSD menu
OK
Make a selection, change image display
▲
Move upward
▼
Move downward
◀
Move left
(press this button for more than 5 seconds to
access to the factory mode)
▶
Move right
(press this button for more than 2 seconds to
reset all the data about user environment)
3 / 6
Rev.120116

OSD Settings
Analog RGB Mode:
IMAGE
BRIGHTNESS
CONTRAST
SHARPNESS
USER IMAGE:
(4 Color Options)
COLOR
RED: Adjust Red
GREEN: Adjust Green
BLUE: Adjust Blue
USER COLOR:
(User selectable
option)
OSD
LANGUAGE: Select
desire language
TRANS: Adjust
Transparency
H_POSITION /
V_POSITION: Adjust
OSD Screen Position
UTIL
FACTORY RESET:
Reset to Factory
Default
Video Mode:
IMAGE
BRIGHTNESS
CONTRAST
SATURATION
HUE
SHARPNESS
USER IMAGE:
(4 Color Options)
OSD
LANGUAGE: Select
desire language
TRANS: Adjust Transparency
H_POSITION: Move Screen
Horizontally
V_POSITION: Move Screen
Vertically
UTIL
FACTORY RESET: Reset to
Factory Default
4 / 6
Rev.120116

Factory Mode: Press for more than 5 seconds on the remote.
IMAGE
Adjusting the Position of the
Navigation Screen
H_POSITION: Move Screen
Horizontally
V_POSITION: Move Screen
Vertically
NAVI MODEL: Do Not Use
AVOUT SELECT: Default, AV1,
AV2, AV3
PARK
PARK ENABLE: Enable/Disable
Parking Guide Line
PARK SETUP: Control the
position of the parking Guide Line
SAFE ENABLE: Turn ON or OFF
VIM Feature
UTIL
CALIBRATION: Do Not Use
IR MEMORY: Do Not Use
DVD TYPE: Setup DVD Type
DTV TYPE: Setup DTV Type
JOG SHUTTLE: Do Not Use
FACTORY RESET: Reset all
values to factory default
Factory Mode: Press for more than 5 seconds on the remote.
PARK
PARK ENABLE: Enable/Disable
Parking Guide Line
PARK SETUP: Control the
position of the parking Guide Line
SAFE ENABLE: Turn ON or OFF
VIM Feature
PARK –ENABLE
A. With ‘PARK ENABLE’ set to ON,
the Parking Guide Line will be
shown on the screen.
B. Press OK button on the remote and
‘H_POS’ will be shown on the right
hand side of the screen. Move the
screen horizontally to the desired
position.
PARK ENABLE
A. Press OK button on the
remote and ‘V_POS’ will be
shown on the right-hand side
of the screen. Move the
screen Vertically to the
desired position.
5 / 6
Rev.120116

DVD Player Model Selection
UTIL –DVD TYPE
NEC/SANYO, DV-108, SANYO-1, SANYO-2, USER
If the DVD player you are using is not NECVOX or SANYO based, you will need to program the remote controller in the
‘IR MEMORY’ section and set the DVD TYPE to USER.
NOTE: If you program the remote in FACTORY Mode, the DVD type will automatically be saved under ‘USER’.
SWC Controls
Press and hold the ‘PHONE PICK UP’ button on
the Steering Wheel Controls for about 2 seconds.
to toggle between the AV sources.
A short press will maintain its OEM function.
6 / 6
Rev.120116