Cult 5055999253277 Installation guide

1
ASSEMBLY & PRODUCT CARE
DINING CHAIR - 460x570x840
5055999253277
Thank you for purchasing this PRODUCT. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 7MINUTES to assemble.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.

2
Fittings and parts checklist
Item
Description
Qty
Item
Description
Qty
Item
Description
Qty
1
Iron leg
1
2
Seat
1
3
Wing Nut
4
Step by step assembly instructions
Step one
Place iron leg (1) and seat (2) on the clean & flat floor to avoid damage

3
Step three
Lock the bolt using the wing nut
Step four
Carefully stand product to its position and place at the location you disired in your home.
FINISH
Your furniture is now safe to use in your home.
Step two
Attach the iron legs (1) by inserting the seat (2) bolt into the hole provided on the corner iron leg

4
Safety Instructions
Never drag furniture when moving it, always lift it.
When lifting or moving a dining chair always do so from under frame.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly
insalled or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
IMPORTANT: If an Anti-topple device is included with this unit, you must install it in
accordance with the instructions provided using fixings suitable for the wall type. If unsure,
please seek advice of a professional.
Care and Maintenance
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
How to care for Painted Wood furniture
Never use sharp items on the surface of the product. For example knives and utensils may
damage the product. It is also advisable to place a mat under paper when writing.
Hand painted brush stroke finish's will hold up to everyday wear and tear quite nicely. However,
it is important to remember that your piece is still a wood piece of furniture and should be cared
for as such.
Painted furniture still requires regular dusting with a damp cloth. When very soiled wash with a
solution of mild, non-abrasive detergent and warm water. Wring a cloth nearly dry and work on
a small section at a time, then rinse with clear water drying after..
Never leave water to settle on the surface as this will cause damage. Any liquid spilled onto the
item should be cleaned up immediately using an absorbent cloth.

5
AVOID chemical cleaners or liquid furniture polish including direct contact with greasy
substances.
As with all natural wood products, there will be some movement within the parts as the furniture
acclimatises to its surroundings, you may see slight chipping and cracks where panels meet,
this is a completely natural occurrence with ALL painted products using natural solid timbers.
Painted surfaces can be carefully touched up with matching paint.
There will be various brush lines, slubs, and little inconsistencies in the painted finish, this is all
part of the relaxed handfinished look and feel of hand painted collections.
How to care for Metal furniture
Never use sharp items on the surface of the product. For example knives and utensils may
damage the product. It is also advisable to place a mat under paper when writing.
Metal furniture requires minimal maintenance:
Cleaning your metal furniture is very simple. Use a soft cotton cloth and clean with mild
detergent or water, using a towel immediately dry the furniture afterwards.
Metal furniture is usually damaged due to rust, as a precaution a soft wax after cleaning will
help seal it.
If it has a few spots of rust, you can treat it with rust remover, following the manufacturers
guidelines. (some finishes are made to look like rust)
Smudges and smears can be removed from metal furniture by using a window cleaner and a
paper towel.
Indoor metal furniture is not recommended for outdoor use.
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE