Cult WYCOMBE User manual

WYCOMBE CONSOLE TABLE
Thank you for purchasing this Wycombe console table. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full
checklist of components is given in this leaflet. If any components are missing,
please contact the retailer from whom you bought this product
This product is HEAVY, it should be assembled as near as possible to the point of use
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 30 MINUTES to assemble with 1 PERSON.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM
YOUNG CHILDREN .
Read this leaflet in full before commencing assembly.
Page 1 of 4

Parts
Top x 1
ab
Step by step assembly instructions
Step 1
Page 2 of 4
Leg x 4
Attach Leg onto the Top as shown in figure.
ba
Hardware
1
Hardware
Bolt 70 mm x 4Allen key x 1
2
Flat washer x 4 Spring washer x 4
34
HINT
Ensure Table top is
Protected by packaging
When upside down to
avoid damage
b
Leg
b
Leg
b
Leg
b
Leg
a
Top
2
3
1
4

Page 3 of 4
Care and Maintenance
Assembly is complete.
How to care for your wood furniture
Please do not use abrasive cleaners or silicone-based products on your product as this may damage to product
surface, a soft natural Beeswax is recommended, follow the instructions supplied or printed on the container.
A soft cloth should be used for cleaning we do not recommend the yellow duster type as these can leave fibers
on the surface.
Always use mats and coasters with cork/felt backing when placing hot items onto the surface of your product. Avoid mats
and coasters with plastic/rubber backs/feet they can leave un-reversible marks on your furniture surface over time.
Never use sharp items on the surface of the product; knives and utensils may damage the timber. It is advisable
to place a mat under paper when writing
Never overload an item such as a shelf that may be beyond what the shelf is reasonably expected to hold.
Any liquid spilled onto the item should be cleaned up immediately using an absorbent cloth. Please ensure
the surface is completely dry.
Please do not sit or place an amount of weight onto the edge of a tabletop as this may cause the table to tip.
Never attempt to lift heavy furniture on your own, always seek assistance and where ever possible please
dismantle any heavy items before moving them to a new location.
Please periodically tighten bolts and screws on all self-assembly items, as these may work loose over time.
Your furniture will endure most temperatures in your home, but it is recommended that placing it next to a heat
source such as a fire or radiator is avoided. This is particularly recommended with solid timbers as the heat may
cause the timber to warp, crack or split.
“When cared for properly, this hand crafted furniture willprovide you with years of
enjoyment in your home."

Safety Instructions
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No
liability will be accepted for damage or injury cause by incorrectly installed or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely dis-assembled to
avoid personal injury or damage to the furniture. Please be careful to retain all fittings when doing this
Understanding your Furniture Purchase – After Care Advice
Timber Characteristics
Timber is a natural product and will have small knots, burrs and inconsistent grains. These occur when the tree
grows in the forest, and may still be visible in even the most meticulously selected timber - This should not be
seen as a blemish but the proof of the highly individual nature of this fine material.
Wood displays different grain patterns depending on which way they are cut - for example, quarter sawn timbers
(See image) can enhance the natural characteristics of the grain and show off the 'medullary ray'.The
'medullary ray' which can appear in oak furniture is a mark of good quality timber - these are just characteristics
of the natural beauty of the wood.
Timber will continue to expand and contract throughout the year and will acclimatise to its surroundings; slight
movement between panels and hairline cracks within the grain will occur. This is totally natural and is expected
from a natural material such as timber e.g. hairline cracks in the grooves or slight movement in panels or tenon
joints are a commonplace.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade from items
that have been previously purchased with the same finish. Colour variance between solids and veneers may be
visible; every effort is made to reduce this variance in the manufacturing process.
Some furniture may use filler to reduce visibility of joint lines and knots. This is all part of the manufacturing
process to assure the highest visual finish to your furniture.
Furniture finishes can vary, some ranges of furniture may require an antiqued look. The surface of this Timber
will be purposely dented, scratched and left rough; this completes the look of the furniture and adds another
completely unique element to your furniture.
Each piece of furniture is unique and will not be identical to the rest of the pieces in the range. Not one piece of
timber is the same; it's your own personal piece.
Page 4 of 4