Cult 5059413395918 User manual

1
ASSEMBLY & PRODUCT CARE
2 DRAWER DESK –1300 x 500 x 760
5059413395918 / 5059413395925
Thank you for purchasing this PRODUCT. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.

2
Fittings and parts checklist
Item
Description
Qty
Item
Description
Qty
Item
Description
Qty
1
Top table
1
2
Leg
2
3
Appron
2
A
Bolt 6x60mm
6
B
Flat washer
10
C
Spring washer
10
D
Allen key
1
E
Bolt 6x50mm
4
1
2
3

3
Step by step assembly instructions
Step two
Attach legs (2) to appron (3) on both side using bolts (E), flat washers (B), and spring washers
(C) by allen key (D) as supplied.
Step one
Place top table (1) upside down on the clean carpet or blanket to avoid damage to the surface
BOLT 6X50 (E)

4
Step three
Attach legs (2) to top table (1) using bolts (A), flat washers (B), and spring washers (C) by allen
key (D) as supplied.
Step four
Carefully stand product to upright position.
FINISH
IMPORTANT: WHEN LIFTING OR MOVING THE TABLE ALWAYS DO SO FROM THE
UNDER FRAME AND NOT THE TABLE TOP
Step Five
Secure the desk to the wall using the anti-topple kit provided, following the instructions detailed
below. When fitted properly, the device will not be visible during general product use.
IMPORTANT: Securing your furniture to the wall with this kit will prevent injury/property damage
from unexpected tipping of furniture, particularly to avoid serious injury to children.
BOLT 6X60 (A)

5
IMPORTANT: The device must be fitted to this product in accordance with the following parts: 1
x plastic cable tie, 1 x plastic wall bracket.
IMPORTANT: Fittings into the wall are not included. You will need to choose screws/fittings
which are appropriate for securing the device to the type of walls you have. If you are unsure
what wall fixing you require, please seek professional advice. The anti-topple device must not
be modified or altered in any way.
1. Position your furniture in desired location in your home. Take the plastic cable tie and feed
through loop hole provided under the table frame
2. Then feed the wall bracket onto the cable tie and press bracket firmly onto the wall flat.
3. Mark with a pencil through the bracket holes onto the wall where the wall fixings will need to
be inserted. Temporarily move furniture from wall and prepare necessary screw holes into your
wall.
4. Fit the plastic wall bracket firmly to your wall using suitable wall fixings. Replace furniture
back to your desired position, then attach cable tie through wall bracket and frame firmly.
Your furniture is now safe to use in your home. Finish.
Safety Instructions
Never drag furniture when moving it, always lift it.
When lifting or moving a table always do so from under frame and not the table top.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly
insalled or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
IMPORTANT: If an Anti-topple device is included with this unit, you must install it in
accordance with the instructions provided using fixings suitable for the wall type. If unsure,
please seek advice of a professional.

6
Care and Maintenance
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
How to care for Painted Wood furniture
Hand painted brush stroke finish's will hold up to everyday wear and tear quite nicely. However,
it is important to remember that your piece is still a wood piece of furniture and should be cared
for as such.
Painted furniture still requires regular dusting with a damp cloth. When very soiled wash with a
solution of mild, non-abrasive detergent and warm water. Wring a cloth nearly dry and work on
a small section at a time, then rinse with clear water drying after..
Never leave water to settle on the surface as this will cause damage. Any liquid spilled onto the
item should be cleaned up immediately using an absorbent cloth.
AVOID chemical cleaners or liquid furniture polish including direct contact with greasy
substances
As with all natural wood products, there will be some movement within the parts as the furniture
acclimatises to its surroundings, you may see slight chipping and cracks where panels meet,
this is a completely natural occurrence with ALL painted products using natural solid timbers.
Painted surfaces can be carefully touched up with matching paint.
There will be various brush lines, slubs, and little inconsistencies in the painted finish, this is all
part of the relaxed handfinished look and feel of hand painted collections.
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE