Custom Audio Electronics HT15 User manual

Version 1.0 D 2013
HT15
User Manual

i
Copyright 2013
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.

ii
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical Power Supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket
must be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or
local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire
or electric shock. Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation

iii
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with
the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding
18kg.the material of a FIRE ENCLOSURE, in the thinnest significant
wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass
the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg
and for all STATIONARY EQUIPMENT, the material of a FIRE
ENCLOSURE, in the thinnest significant wall thickness used, shall
be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

iv
Revision History
Revision Date Description
V1.0 July, 2013 Release

v
Table of Contents
1 Item Checklist................................................1
1-1 Standard Items............................................................................... 1
1-2 Optional Items ................................................................................ 2
2 System View...................................................3
2-1 Front View & Side View .................................................................. 3
2-2 Rear View........................................................................................ 4
2-3 Dimension....................................................................................... 4
2-4 I/O View........................................................................................... 5
3 System Assembly & Disassembly.................7
3-1 Install the Power Adapter............................................................... 7
3-2 Replace the HDD............................................................................ 7
3-3 Open the System............................................................................ 8
3-4 Replace the RAM............................................................................ 9
4 Peripherals Installation.............................. 10
4-1 Install the MSR Module ...............................................................10
4-2 Install the iButton Module ...........................................................11
4-3 Install the Customer Display........................................................12
4-4 Install the 2nd Display .................................................................13
4-5 Install the Cash Drawer................................................................14
5 Specification ............................................... 16
6 Jumper Settings.......................................... 18
6-1 C56 Motherboard.........................................................................18
6-2 C76 Motherboard .........................................................................23
Appendix A: Driver Installation ..................... 28

1
1 Item Checklist
1-1 Standard Items
a. System b. Power adapter (65W)
c. Power cable d. COM-RJ45 cable (x2)
e. Driver CD

2
1-2 Optional Items
a. MSR module b. iButton module
c. Customer display d. 2nd display

3
2 System View
2-1 Front View & Side View
No. Description
1 Touch screen
2 Stand base
3 Power button
4 Ventilation hole
1
2
4
3

4
2-2 Rear View
No. Description
6 MSR /Fingerprint / iButton dummy cover
2-3 Dimension
6 6

5
2-4 I/O View
Number Description
a Cash drawer
b USB x 4 (USB2.0)
c LAN
d COM1~4 (from left to right)
e VGA
f DC Jack 19V
g Power button
h Printer
C56 Motherboard

6
Number Description
a Cash drawer
b USB x 4 (USB2.0)
c COM1~3 (from left to right)
d VGA
e DC Jack 19V
f Power button
g LAN
h USB x 2 (USB3.0)
i Printer
C76 Motherboard

7
3 System Assembly & Disassembly
3-1 Install the Power Adapter
The system is equipped with a 65W or 90W power adapter. Please plug it into the
system as shown below.
1. Place the system face down.
Make sure not to scratch the
monitor.
2. You will find the I/O panel located
at the bottom of the stand.
3. Find the DC Jack on the I/O
panel.(refer to chapter 2-4.) and
connect the power adapter directly
to the DC Jack connector.
3-2 Replace the HDD
1. Use both hands to pull the top
cover of the stand.
2. The HDD is secured by a clip, slide
the clip aside.

8
3. Hold the plastic tab and pull the
HDD outward.
4. To remove the HDD module pull
the ejector clips out of the side of
the module.
3-3 Open the System
1. Use both hand to pull the top cover
of the stand outwards.
2. Remove the screw as shown in the
picture.

9
3. Disconnect the LCD cables (x2).
4. Lay the system on its back to access the bottom of the system.
5. Pull the motherboard tray towards you by the handle
3-4 Replace the RAM
1. Follow the steps described in
Chapter 3-3 to open the system.
2. Find the RAM location on the
motherboard (refer to Chapter
6-1-1 and 6-2-1).
3. Slide the memory module into the
memory slot and press down until
it locks in place.
Removing a RAM module:
To remove the module pull the ejector
clips out of the side of the module.

10
4 Peripherals Installation
4-1 Install the MSR Module
MSR module can be installed to either side of the system. Choose one side and
follow the steps below. Make sure the unit is powered down before starting.
1. Remove the dummy cover first.
2. Connect the MSR cable to the connector on the system side.
3. Insert the MSR module in place and fasten the M3*8L screws (x2) on the
back to secure the module.
4. Finally cover the screw holes by the rubber pads (x2).
*Please note the M3*6 screws (x2) should be removed before inserting the MSR
module.

11
4-2 Install the iButton Module
1. Remove the dummy cover first.
2. Connect the iButton cables to the connector on the system side.
3. Insert the iButton module in place and fasten the M3*8L screws (x2) on the
back to secure the module.
4. Finally cover the screw holes by the rubber pads (x2).
*Please note the M3*6 screws (x2) should be removed before inserting the
iButton module.

12
4-3 Install the Customer Display
1. Use both hands to pull the top cover of the stand outwards.
2. Release the plastic plate from the top cover.
3. Put the top cover of the stand back to the position.
3. Connect the customer display cable (x1) to the connector on system side and
fasten the ground cable (x1) with a M3*4 screw.
4. Attach the customer display and fasten the M4 screws (x2).
5. Cover the screw holes by the rubber pads (x2).
①
②

13
4-4 Install the 2nd Display
1. Use both hands to pull the top cover of the stand outwards.
2. Remove the M3*8 screws (x2) as shown in the picture.
3. Connect the 2nd display cables (x1) to the connector on system side.
4. Attach the 2nd display and fasten screws (x4).
(M4 screw x2 / M3*12 screw x2 )
5. Finally cover the screw holes by the rubber
pads (x4).

14
4-5 Install the Cash Drawer
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
Cash Drawer Pin Assignment
Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Register Location:
48Ch
Attribute:
Read / Write
Size:
8bit
BIT BIT7 BIT6
BIT5
BIT4 BIT3
BIT2
BIT1 BIT0
Attribute Reserved Read
Reserved Write Reserved
7 6 5 4 3 2 1 0
X X X X X
Reserved
Cash Drawer “DOUT bit0” pin output control
Cash Drawer “DOUT bit1” pin output control
Reserved
Cash Drawer “DIN bit0” pin input status
Reserved
Pin
Signal
1 GND
2 DOUT bit0
3 DIN bit0
4 12V / 19V
5 DOUT bit1
6 GND