CyberData 011377 Manual

Quick Reference 931307B © 2017, CyberData Corporation, ALL RIGHTS RESERVED© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931307B Quick Reference
Wall Mounting with Single or Two Gang Box
Contacting CyberData
DIMENSIONS ARE IN INCHES [MILLIMETER]
3.40 [86.4]
ø0.19 [ø4.8]
2.39 [60.8]
3.40 [86.4]
2.65 [67.3]
0.50 [12.8]
0.38 [9.5]
(4 Places)
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Singlewire InformaCast RGB Strobe product page at:
http://www.cyberdata.net/voip/011377/
• Create a plan for the locations of your Singlewire InformaCast RGB Strobes.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
a. Default if there is not a DHCP server present.
RGB Strobe
802.3af Compliant Ethernet Switch
IP Phone IP PBX Server
*More installation and mounting
options are available in the
Operations Guide.
(1) RGB Strobe Assembly
(4) #6 x 1.5 inches
Sheet Metal Screw
(1) Gang Box Mounting Kit
(4) #6 Ribbed Plastic
Anchor
(4) #6-32 x 0.625-inch
Flat-Head Machine Screw
(1) Wall Mounting Kit
The IP Endpoint Company
Installation Quick Reference
Singlewire InformaCast RGB Strobe
011377

© 2017, CyberData Corporation, ALL RIGHTS RESERVED 931307B Quick Reference Quick Reference 931307B © 2017, CyberData Corporation, ALL RIGHTS RESERVED
Wall Mounting Option
Wall Mounting with Single or Two Gang Box
Backplate
Wall
(Not Provided)
Network Cable &
Screw
121001A
AccessoryKit
(4 Places) on Wall
Pre Drill Holes
Ground Wire
Cutout
for Ground Wire Connection
Pick One of Four Mounting Hole
Slot
Entry
Cable
Closed
Slots
Cable
Mounting
Screw (3x)
Single Gang Box use two
Wall Cutout
or Two Gang Box
Backplate accept
Single Gang Box
Two Gang Box use Four
Backplate
Wall Cutout
Screw
121002B
AccessoryKit
(Not Provided)
Network Cable & Ground Wire
Available Mounting Hole
Pick One of Two or Four
for Ground Wire Connection
Mounting
Screw (3x)
Slot
Entry
Cable
Closed
Slot
Cable
Dimensions
Connections
RTFM Button
2.1 [55] 4.5 [115]
DIMENSIONS ARE IN INCHES [MILLIMETERS]
4.5 [115]
0.25"
Terminal Block
Wire (IN)
can accept 16 AWG wire
1
8
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
When the device is operational and linked to a
network, you can use the Reset Test Function
Management (RTFM) button (SW1) to restore
the device to the factory default settings.
To restore the device to factory default
settings:
• Press and hold the RTFM button for
seven seconds, and then release the
RTFM button.
RTFM button