CYmodel f4u corsair User manual

SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time buildersshould seekadvice frompeople havingbuilding
experience inorder toassemble themodel correctlyand toproduce
its performanceto fullextent. ,
lAssemble thiskit onlyin placesout ofchildrens reach!
lTakeenough safetyprecautions priorto operatingthis model.
,
You areresponsible forthis models assemblyand safeoperation!
lAlways keepthis instructionmanual readyat handfor quick
reference,even aftercompleting theassembly.
lCould causeserious injuryor evendeath
SPECIFICATION
Wing Span: 2400mm (94.5in)
2
Wing Area: 106.7dm (1654.5sq.in)
Total Length: 2165 mm (85 in)
Engine :100cc gas engine
Radio : 6-7 channels ,11 servos
F4U CORSAIR
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8018

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGIN
SharpHobby Knife Phillips Screw Driver Awl
NeedleNose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 6-7channel radio for airplanes (with 11servos).
And dry batteries.
CAUTION: Only use a minimum 6-7channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 6 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB2mm2mm
99
44
11
77
66
55
88
Model Airplaneengine:100ccgasengine
receiver
22
Battery (need 2)
33
Servo(need 11servos )
remote control
Switch (need 2)
AA
Muffler

!
3
2
1
5
4
33
Hinge
Bottom view
Install the elevator
glue the hinges with Epoxy
Install the elevator servos
Install the aileron and flap
Install the aileron and flap servo
Accessory list for this page.
LL
RR
LL
RR
AB
- - - - - - - - 8
Make sure hingesare
mounted in thesame line
LL
RR
Horn
Rod adjuster
Connecting rod head
2.5X85mm rod
4X35mm screw
3X10mm Screw
3X14mm Screw
3mm Lock nut
- - - - - - 2
- - - - - - 2
- - - - - - 4
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
3mm screw
- - - - - - 2
Hinge
Hinge
FlapAileron
- - - - - - - - 4
- - - - - - - - 8
Make sure hingesare
mounted in thesame line
AB
AB
Horn
Rod adjuster
Connecting rod head
2.5X85mm rod
4X35mm screw
3X10mm Screw
3X14mm Screw
3mm Lock nut
- - - - - - 4
- - - - - - 4
- - - - - - 8
- - - - - - 4
- - - - - - 4
- - - - - - 4
- - - - - - 4
- - - - - - 4
- - - - - - 4
3mm screw
- - - - - - 4
2.3X10mm Tp screw
- - - - - 6
Horn
Rod adjuster
Connecting rod head
2.5X85mm rod
4X35mm screw
3X10mm Screw
3X14mm Screw
3mm Locknut
- - - - - - 6
- - - - - - 6
- - - - - - 12
- - - - - - 6
- - - - - - 6
- - - - - - 6 - - - - - - 6
- - - - - - 6
- - - - - - 6
3mm screw
- - - - - - 6
2.3X10mm Tp screw
- - - - - 6
Hinge
Hinge
- - - - - - 4
- - - - - - 16

!
8
7
6
10
9
44
Accessory list for this page.
Install the flap, Drill 4.5mm hole
for flap hinges as show
LL
RR
LL
RR
Hinge
- - - - - 8
A B
Install the flap servo
notice:double check and made sure both
flap panel can be moving together by
spring but will not jam before you
glue the flap hinges
Install a 5mm control spring
in to both flap panel.
LL
RR
Horn
Rod adjuster
Connecting rod head
2.5X45mm rod
4X50mm screw
3X10mm Screw
3X14mm Screw
3mm Lock nut
- - - - - - 2
- - - - - - 2
- - - - - - 4
- - - - - - 2
- - - - - - 2 - - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
3mm screw
- - - - - - 2
Main wing
AB
Install M5blind nutinside eachwing
mount blockfrom insidethe glue
them withEpoxy
Hard wood
- - - - - - 2
6mm Bind nut
- - - - - 4
6X125mm screw
- - - - - 4
6mm Washer
- - - - - 4
Placing the center wing on to the fuse,Bottom
then follow mount bolt area to drill four 5mm
hole from bottom of center wing and mounting
block inside the fuse.
6mm Bind nut
- - - - - 4
6X125mm screw
- - - - - 4
6mm Washer
- - - - - 4
Hinge
- - - - - 8
Horn
Rod adjuster
Connecting rod head
2.5X45mm rod
4X50mm screw
3X10mm Screw
3X14mm Screw
3mm Lock nut
- - - - - - 2
- - - - - - 2
- - - - - - 4
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
- - - - - - 2
3mm screw
- - - - - - 2

!
13
12 15
1414
55
11
Accessory list for this page.
Install the rudder servo
Install the rudder
AB
Hinge
- - - - 2
A B
Install the rudder servo
AB
4mm4mm
4X25mm screw 4mm Washer
- - - - - - - - 2
- - - - 2
Install the elevator
Main wing&Horizontal/Vertical tail
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
AA
B B
C C
A
A
B B
C C
Rod adjuster
Connecting rod head
3X25mm screw
2X8mm screw - - - - - 2
- - - - - 1
- - - - - 1
- - - - - 2
2.5X85mm rod
- - - - - 1
Installation aluminum tubes,
in the following, corresponding
aluminum tubes, drill a 4 mm hole,
then install M4 screws
Rod adjuster
Connecting rod head
3X25mm screw
2X8mm screw
- - - - - 2
- - - - - 1
- - - - - 1
- - - - - 2
2.5X85mm rod
- - - - - 1
Hinge
- - - - 2
4X25mm screw 4mm Washer
- - - - - - - - 2
- - - - 2

!
18
17 20
19
16
66
Accessory list for this page.
Install the main landing gear
LL
RR
Install the main landing gear
Install the main landing gear
LL
RR
Mount the main gear in to the gear
bay and fix it by six mount bolt as
show.the wheel for this model
are 4.5in or 115mm
Install the main landing gear
if you plan to use lading gear door,
you need to open four slot on the
landing gear bay for the door hinges.
you also need to glue two hinges in
each side landing gear door.
you also need to glue two hinges in
each side landing gear door.
Install the tail wheel
Install the tail gear ang tail gear servo as show.
Notice: this servo need minimum 3kg torque.
Unless it can be fail to controll or damage.

!
23
25
77
21 24
22
Accessory list for this page.
Installing the engine (100cc)
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe Air pressure line
Install the throttle servo
Assembly of the full tank
175mm
1.8X450mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
ThrottleThrottleFuel tankFuel tank
Radio Equipment
ReceiverReceiver
BatteryBattery
Battery/IgnitionBattery/Ignition
Installing the engine
AB
1.8X450mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1

!
28
27 30
29
88
26
Accessory list for this page.
Install the cover
Install the thr cowling
3mm Washer
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
Install the canopy
Install the cover
SpinnerSpinner
PropellerPropeller
AB
2.6X12mm Tp screw
- - - - - 6
Cut awaythe surpluspats ofcanopy
care fullyalong theshaded line.
Cut off excess part
Fasten
- - - - - - - - - - 3
LL
RR
Install the thr cowling
3mm Washer
3X16mm screw
3mm rubber band
2.6X12mm Tp screw
Fasten
- - - - - - - - - - 3
- - - - - - - - - - 6
- - - - - - - - - - 6
- - - - - - - - - - 6
- - - - - - - - - - 6

33
32 34
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
31
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit generalflight capabilities.
Readjust according to your needs and flight level.
99
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
155-165mm155-165mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45