CYmodel fokker DR-1 User manual

SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time buildersshould seekadvice frompeople havingbuilding
experience inorder toassemble themodel correctlyand toproduce
its performanceto fullextent. ,
lAssemble thiskit onlyin placesout ofchildrens reach!
lTakeenough safetyprecautions priorto operatingthis model.
,
You areresponsible forthis models assemblyand safeoperation!
lAlways keepthis instructionmanual readyat handfor quick
reference,even aftercompleting theassembly.
lCould causeserious injuryor evendeath
SPECIFICATION
Wing Span: 2400mm (94.5in)
2
Wing Area: 118.5dm (1837sq.in)
Total Length: 2070 mm (81.5 in)
Engine :80-100cc gas engine
Radio : 4 channels ,6 servos
Fokker DR-1
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8119C

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGIN
SharpHobby Knife Phillips Screw Driver Awl
NeedleNose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 4channel radio for airplanes (with6servos).
And dry batteries.
CAUTION: Only use a minimum 4channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 6 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB2mm2mm
99
44
11
77
66
55
88
Model Airplaneengine:100-150ccgasengine
receiver
22
Battery (need 2)
33
Servo(need 6 servos )
remote control
Switch (need 2)
AA
Muffler
Muffler

Accessory list for this page.
LL
RR
LL
RR
Rod adjuster
Connecting rod head
3X25mm screw 2X8mm screw - - - - - 4
- - - - - 2
- - - - - 6 - - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
LL
RR
A B
- - - - - - - - 8
3mm3mm
2.6X12mm Tp screw
- - - - - 8
Servo line
BA
!
3
2
1
5
4
33
Install the aileron
Install the servo of aileron
Install the servo
Hinge
Install the aileron
Make sure hings are
mounted in the same line
LL
RR
Top wing
Bottom view
Top wing
4X30mm screw
- - - - - 2
4mm Washer
- - - - - 2
4.2mm4.2mm
20X705mm tube
Rod adjuster
Connecting rod head
3X25mm screw
2X8mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
2.6X12mm Tp screw
- - - - - 8
Hinge
4X30mm screw
- - - - - 2
4mm Washer
- - - - - 2
- - - - - 8

Accessory list for this page.
!
8
7
6
10
9
44
Install the rudder
Install the elevator
- - - - - - - - 6
Hinge
AB
AB
LL
RR
BA
Warning!
£¡
!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
1mm
Install the elevator
- - - - - - - -2
Hinge
Install the elevator
4.2mm4.2mm
4X30mm screw
- - - - - 4
4mm Washer
- - - - - 4
A A
A=A
Warning!
£¡
!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
Warning!
£¡
!
Horizontal/Vertical tail
Mean line
4X30mm screw
- - - - - 4
4mm Washer
- - - - - 4
- - - - - 8
Hinge

Accessory list for this page.
!
13
12
11 14
55
Install the rudder servo
Install the main landing gearInstall the elevator servo
Rod adjuster
Connecting rod head
Rod
3X25mm screw
3mm Lock nut
2X10mm screw
- - - - 4
- - - - 2
- - - - 4
- - - - 3
- - - - 3
- - - - 4
1300mm Steel wire
- - - - 2
Aluminium tube
- - - - - 4
HORN
- - - - - 2
4X30 Screw
- - - - - 2
Rod adjuster
Connecting rod head
3X25mm screw
2X10mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X125mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
Install the tail pry
Install the main landing gear
15
9mm plywood
3X20mm Tp screw
Pressure plate
- - - - - -12
- - - - - - 4
5.2mm Collar 5.2mm Nylon collar 3X3mm screw
- - - - - - 2 - - - - - - 2 - - - - - - 2
A B
LL
RR
Rod
3mm Lock nut
2X10mm screw
- - - - 4
- - - - 3
- - - - 4
1300mm Steel wire
- - - - 2
Aluminium tube
- - - - - 4
Rod adjuster
Connecting rod head
3X25mm screw 2X10mm screw
- - - - - 8
- - - - - 4
- - - - - 9 - - - - - 8
2.5X125mm rod
- - - - - 2
HORN - - - - - 4
- - - - - 2
4X30 Screw
- - - - - 4
3X20mm Tp screw
Pressure plate
- - - - - -12
- - - - - - 4
5.2mm Collar
5.2mm Nylon collar
3X3mm screw
- - - - - - 2
- - - - - - 2
- - - - - - 2

Accessory list for this page.
!
18
17
16 19
66
Install the below wing Install the wing support
20
Install the middle wing
4X55mm screw
- - - - - 2
4mm Washer
- - - - - 2
4X30mm screw
- - - - - 2
4mm Washer
- - - - - 2
4.2mm4.2mm
Install the middle wing
5X30mm screw
- - - - - 2
5mm Washer
- - - - - 2
20X705mm tube
20X835mm
tube
AB
4X16mm screw
- - - - - 2
4mm Washer
- - - - - 4
4mm plywood
4mm plywood
- - - - - 2
- - - - - 2
4mm Lock nut
- - - - - 2
B
Pressure plate
- - - - - 3
3X20mm Tp screw
- - - - - -6
3X12mm Tp screw
- - - - - -4
Pressure plate
- - - - - - 2
Parallel
B
B
B
AB
4X55mm screw
- - - - - 2
4X16mm screw
- - - - - 2 4mm Washer
- - - - - 8
4mm Lock nut
- - - - - 2
5X30mm screw
- - - - - 2
5mm Washer
- - - - - 2 Pressure plate
- - - - - 3
3X20mm Tp screw
- - - - - -6
3X12mm Tp screw
- - - - - -4
Pressure plate
- - - - - - 2
4X30mm screw
- - - - - 2

Accessory list for this page.
!
23
22
21 24
77
25
AB
AB
Install the top wing
4X16mm screw
- - - - - 2
4mm Washer
- - - - - 4
4mm Lock nut
- - - - - 2
4mm plywood
- - - - - 2
A B
3X16mm screw
- - - - - 8
3mm Lock nut
- - - - - 8
3X20mm screw
- - - - - 12
Install the engine mount
Assemble horizontal tail, tail gear
separately
D’
D
CC’
C =
D = D’
C’
E
E’
F
F’
E =
F =
F’
E’
Install the top wing Install the engine
ThrottleThrottleFuel tankFuel tank
1.8X350mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Throttle servo
4X16mm screw
- - - - - 2 4mm Washer
- - - - - 4
4mm Lock nut
- - - - - 2
4mm plywood
- - - - - 2
3X16mm screw
- - - - - 8
3mm Lock nut
- - - - - 8
3X20mm screw
- - - - - 12
1.8X350mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1

Accessory list for this page.
!
28
27
26 29
88
30
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe Air pressure line
ReceiverReceiver
BatteryBattery
Battery/IgnitionBattery/Ignition
Radio Equipment
Install the cowling
Install the canopy
3mm Washer
- - - - - 5
3X16mm screw
- - - - - 5
3mm rubber gasket
- - - - - 5
3mm Washer
- - - - - 2
3X25mm screw
- - - - - 5
3mm rubber gasket
- - - - - 2
Cut off the surplus part along the
shaded area
Assembly of the full tank
502
C.AC.A
Install the canopy
3X25mm screw
- - - - - 5
3mm Washer
- - - - - 7
3X16mm screw
- - - - - 5
3mm rubber gasket
- - - - - 7

32
32
5
34 Centre of Gravity.
Adjust the travel of each control surface tothe
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Adjust the travel of each control surface tothe
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
31
AILERON
Adjustment.
Top view
Adjust the travel of eachcontrol surface tothe
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Adjustment.
Adjustment.
99
Side view
Top view
Top viewTop view
Side viewSide view
CG
45
45
45
45 45
45