CYmodel Spitfire MK IX User manual

SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience inorder to assemble the model correctly and to produce
its performance tofull extent. ,
lAssemble this kit only in places out ofchildrens reach!
lTake enough safety precautions prior tooperating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Spitfire MK IX
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8144B
Wing Span:2350 mm (92.5 in)
2
Wing Area:91.8 dm (1423sq.in)
Total Length: 2000 mm (78.8 in)
Radio : 6channels , 9 servos
Engine : 50cc gas engine

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGIN
SharpHobbyKnife Phillips Screw Driver Awl
NeedleNosePliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 6channel radio for airplanes (with 9servos).
And dry batteries.
CAUTION: Only use a minimum 6channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 6 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB2mm2mm
99
44
11
77
66
55
88
Model Airplaneengine:50ccgasengine
receiver
22
Battery (need 2)
33
Servo(need 9 servos )
remote control
Switch (need 2)
AA
Muffler
Muffler
Muffler
Muffler
Ignition
Ignition

!
3
2
1
5
4
33
Install the aileron and flap
Install the servo of aileron
Install the servo
Aileron
Flap
Hinge
Hinge
Install the aileron and flap
Bottom view
Install the servo of flap
Hinge
Hinge
Accessory list for this page.
LL
RR
LL
RR
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
LL
RR
FlapAileron
AB
AB
- - - - - - - - 6
- - - - - - - - 6
A B
A B
Make sure hingesare
mounted in thesame line
LL
RR
Flap Aileron
Tailing edge
Aileron
4mm
Servo line
LL
RR
Servo line
AB
AB
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
2.6X12mm Tp Screw
8
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
2.6X12mm Tp Screw
8
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
4
8
4
8
4
8
3mm Lock nut
2.6X12mm Tp Screw
16
6
6

!
8
7
6
10
9
44
Accessory list for this page.
Air tank
Switch
Air inlet
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
Quick release connector
Quick release connector
Pressure reduction inlet
Strut
Strut
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight . Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2
Install the main landing gear
Install the main landing gear Main wing installing(Bottom)
LL
RR
Install the main landing gear
4mm4mm
4X35mm screw 4mm Washer
- - - - - - - - 4
- - - - 4
32X755mm Tube
20X55mm Tube
Main wing installing(Top)
Servo line
Servo line
Air line
Air line
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2
4X35mm screw
4mm Washer
- - - - - - - - 4
- - - - 4
LL
RR
Ply wood
- - - - - - - - - - - -2
A B
3X8mm screw
- - - - - - - - - - - -4
6mm Plywood
3X20mm Tp screw
- - - - - 8
4mm Lock nut
- - - - - 2
Ply wood
3X8mm screw
3X20mm Tp screw
- - - - - 8
4mm Lock nut
- - - - - 2
- - - - - 2
- - - - - 4

!
13
12 15
1414
55
11
Accessory list for this page.
Install the elevator
Install the elevator
Install the elevator servos
Install the rudder
Install the elevator servos
LL
RR
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
LL
RR
Bottom view
LL
RR
make sure hingesare
mounted in thesame line
Hinge
- - - - - - - 3
A B
A B
LL
RR
make sure hingesare
mounted in thesame line
AB
Hinge
- - - - - - - - 6
LL
RR
LL
RR
Servo line
AB
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
Hinge
9

!
18
17 20
19
16
66
Accessory list for this page.
Install the rudder
Install the servo of rudder&tail wheel
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Tailing edge
Rudder
4mm
AB80mm spring
- - - - - 2
Install the servo of rudder&tail wheel
Install the servo of rudder&tail wheel
Install the servo of rudder&tail wheel
AB
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
2
2
3mm Lock nut
2
2
2
Aluminium tube
Rod
Rod adjuster
3X16 Screw
2
2
2
3mm Lock nut
2
2
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
4
4
3mm Lock nut
2
4
4
Rod adjuster
2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
6X9 screw
M3X20 Tp screw
3.2mm Rocker
6mm nut 1
1
3
1
3
1
2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
6X9 screw
M3X20 Tp screw
3.2mm Rocker
6mm nut 1
1
3
1
3
1
2
Spring 2

!
23
25
77
21 24
22
Accessory list for this page.
4X20mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
4mm4mm
Horizontal
(Put the servo into the fuselage)
502
C.AC.A
5mm Bind nut
5X45mm screw
- - - - - 2
5mm Washer
- - - - - 2 - - - - - 2
8X50mm Carbon tube
- - - - - 2
5mm5mm
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
AA
B B
C C
AA
B
B
C
C
Main wing&Horizontal/Vertical tail
Warning!
!
8mm8mm
Main wing installing
Installing the engine (50cc)
AB
ThrottleThrottle Fuel tankFuel tank
4X20mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
5X30mm screw
- - - - 4
8X40mm Carbon tube
- - - - - 2
1.8X200mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Install the throttle servo
1.8X200mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1

3mm3mm
Plywood
Cowling
!
28
27 30
29
88
26
Accessory list for this page.
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe Air pressure line
Assembly of the full tank
Radio Equipment
Install the thr cowling
ReceiverReceiver
BatteryBattery
Battery/IgnitionBattery/Ignition
3mm Bind nut
3mm Washer
- - - - - 6
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
6mm Plywood
- - - - 6
Install the thr cowling
AB
SpinnerSpinner
PropellerPropeller
3mm Bind nut
3mm Washer
- - - - - 6
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
6mm Plywood
- - - - 6
2.3X10Tp screw
- - - - - 6
Cut away the surplus pats
of canopy,care fully along
the shaded line.
Install the canopy
2.3X10Tp screw
- - - - - 6

!
33
35
99
31 34
32
Accessory list for this page.
Install the canopy
Install the canopy
Install the canopy
Install the canopy
502
C.AC.A
AB
LL
RR
502
C.AC.A
LL
RR
AB
502
C.AC.A
Blcak lineBlcak line
Red lineRed line
1.5V1.5V 1.5V1.5V
BatteryBattery

38
37 39
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
36
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
1010
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
150-160mm150-160mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45