CYP SY-P293 User manual

SY-P293
PC to HDMI (1080p) Scaler
OPERATION MANUAL

1. Introduction 1
2. Features 1
3. Package Contents 1
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2
4.2 Rear Panel Diagram 3
4.3 Connection Diagram 4
5. OSD Menu Reset 4
5.1 OSD Menu Operations 5
5.2 Supported Resolutions 6
6 Specications 6
Table of Contents

1. Introduction
The SY-P293 is designed to upscale analogue video signal from a PC source to
a digital HDMI output boosting a wide-range of HDTV and PC resolutions up to
1080p/WUXGA. The SY-P293 also converts inputted audio signal from Optical
(Toslink) or analogue L/R to both digital and analogue audio outputs. Audio is
then combined with HDMI video output audio simultaneously. The SY-P293 has
a comprehensive OSD menu that allows the user to select a variety of output
resolutions and adjust for best picture quality.
2. Features
• v1.3 HDMI, HDCP 1.1 and DVI 1.0 compliant.
• Scales any PC resolutions to PC (VGA ~ WUXGA)/ HD (480i ~ 1080p)
resolutions.
• Automatic detection of the factory setting of the connected display and output
the corresponding resolution and refresh rate, when the NATIVE output is
selected (default setting).
• Provides output picture adjustment on contrast, brightness, hue, saturation,
sharpness, RGB (colour tone) level and aspect ratio size.
• Supports high resolution output (See section “6.2. Support Resolution” for
reference):
• PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA.
• SD/HD: 480i, 576i, 480p, 576p, 720p, 1080i and 1080p
• Supports stereo LPCM analogue/digital audio input and stereo LPCM
analogue/digital output. Simply select from the audio input sources in the OSD
menu, the audio is then outputted to HDMI, Optical (Toslink) and mini-jack
simultaneously.
3. Package Contents
• SY-P293
• 5V DC power supply adaptor.
• Operation Manual.
Page 1

Page 2
4. Operation Controls and Functions
4.1 Front Panel
1. PC Input: Connect the PC input D-Sub (15-pin) port to the D-Sub output port
of your source equipment such as a PC.
2. Audio Input: Connect the PC 3.5mm stereo mini-jack input port to the
analogue audio output port of your source equipment.
3. Optical (Toslink) Input: Connect the Optical input port to the Optical output
port of your source equipment.
4. Power: Plug the 5VDC power supply into the unit and connect the adaptor to
AC wall outlet.
PC AUDIO OPTICAL
DC 5V
INPUT
1 2 3 4

Page 3
4.2 Rear Panel
1. HDMI Output: Connect the HDMI output port to the HDMI input port of your
HDTV display.
2. Optical (Toslink) Output: Connect the optical output port to the Optical input
port of your amplier.
3. Audio Output: Connect the 3.5mm stereo mini-jack output port to the analogue
audio input port of your equipment.
4. Menu Button: Press the MENU button to bring up OSD operation menu. (See
section “4. OSD Operation” for reference.)
5. +/- Button: On the rst tier of OSD menu, use + and – buttons to move up/
down the highlight item for selection.
• Once the desired option is selected, use + and – buttons to toggle between
setting values.
Note: Outside of the OSD Menu, Press [-] Button to activate the Auto Adjust
function. The screen will show Auto Adjust.
Press [MENU] and then [-] to switch to 480p mode.
Press [MENU] and then [+] to switch to XGA mode
HDMI AUDIO
MENU +
-
OPTICAL
OUTPUT
1 2 3 4 5

Page 4
4.3 Connection Diagram
5. OSD MENU Reset Fuction
To reset the unit, press and hold the MENU button then insert the DC power
into the unit to set the unit back to factory default, with output resolution set to
NATIVE. This feature is also useful when the output is scaled to a resolution not
supported by the connected TV/monitor so no picture is shown, because the
NATIVE resolution can guarantee to display.

5.1 OSD Menu Operations
Page 5
1st Tier Option 2nd Tier Option Adjustment
CONTRAST - 0 ~ 100 of Contrast Level
BRIGHTNESS -0 ~ 100 of Brightness Level
FINETUNE
- HUE 0 ~ 100 of Hue Level
- SATURATION 0 ~ 100 of Saturation Level
- SHARPNESS 0 ~ 100 of Sharpness Level
- EXIT Back to 1st Tier
COLOR
- RED 0 ~ 100 of Red Colour Level
- GREEN 0 ~ 100 of Green Colour Level
- BLUE 0 ~ 100 of Blue Colour Level
- EXIT Back to 1st Tier
SIZE - FULL / OVERSCAN / UNDERSCAN / LETTERBOX /
PANSCAN
OUTPUT -
NATIVE / VGA / SVGA / XGA/ SXGA /UXGA / 480i /
480p/720p@60Hz / 1080i@60Hz /1080p@60Hz
/ 576i / 576p /720p@50Hz / 1080i@50Hz
/1080p@50Hz / WXGA / WSXGA / WUXGA
AUDIO -EAR PHONE / OPTICAL
OSD
- HPOSITION 0 ~ 100 of OSD Horizontal Position
- VPOSITION 0 ~ 100 of OSD Vertical Position
- TIMER 0 ~ 100 of OSD Existing Time (sec.)
- BACKGROUND 0 ~ 100 of OSD Transparent Level
- EXIT Back to 1st Tier
INFORMATION -
SOURCE (Input Interface) INPUT (Input Resolution)
OUTPUT (Output Resolution) VERSION (Firmware
Version)
Mirror ON/OFF
EXIT -Close OSD Menu
Note: Finetune function works differently under component and VGA input
therefore, Hue, Saturation and Sharpness are only adjustable when the input
signal is component.

Page 6
PC Input Port x 1 VGA (15 PIN DSUB)
HDCP Version V1.1
HDMI Output Port 1 X HDMI
HDMI Specication V 1.2
Analogue Audio Input 3.5mm Stereo Jack
Analogue Audio Output 3.5mm Stereo Jack
Digital Audio Inputs 1 x Optical (Toslink)
Digital Audio Outputs 1 x Optical (Toslink)
Power Supply 5VDC/2.6A (US/EU standards, CE/FCC/UL Certied)
Dimensions (mm) 154(D) x 100(W) x 25(H)
Chassis Colour Black
Chassis Material Aluminium
Operating Temperature Operating from 0°C ~ 48°C
Weight (g) 340
Resolutions PC INPUT HDMI OUTPUT
PC SD/HD PC
480I/576I (NTSC/PAL) V
480P/576P V
720P@(50/60) V
1080I@(50/60) V
1080P@(50/60) V
VGA@(60/72/75/85) V V@60
SVGA@(56/60/72/75/85) V V@60
XGA@(60/70/75/85) V V@60
SXGA@(60/75/85) V V@60
UXGA@60 V V
WXGA@60(1280x800) V V
WSXGA@60(1680x1050) V V
WUXGA@60(1920x1200) V V
Note:VGA/SVGA/XGA/SXGA/output only support@60Hz
5.2 Supported Resolutions
6. Specications

Notes:

www.cypeurope.com
v1.01