CYP PU-22HC User manual

PU-22HC
HDMI/CAT6 to HDMI/
CAT6 Splitter Switcher
Operation Manual
PU-22HC

Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
 Always follow basic safety precautions to reduce the risk of
fi re, electrical shock and injury to persons.
 To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
 Never spill liquid of any kind on or into this product.
 Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
 Do not attach the power supply cabling to building surfaces.
 Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
 To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No Date Summary of Change
V1 20091208 Preliminary Release

Table of Contents
1
1
1
1
2
3
4
4
5
6
7
9
1. Introduction…………………………………………………........……….
2. Applications……………………..…………………………................….
3. Package Contents…………………………......…………….............…
4. System Requirements……...…………………..….…………........…….
5. Features…………………………………………….......……........………
6. Specifi cations..………………………………………...........………...….
7. Operation Controls and Functions………………...……........………
7.1 Front Panel ...............................................................................
7.2 Rear Panel……………......………………………….........…….…
8. RJ-45 Pin Defi nitions …….………………….......................…..…..…...
9. Connection and Installation.............................................................
10. Acronyms ...........................................................................................

1. Introduction
The HDMI/CAT6 to HDMI/CAT6 Splitter Switcher is the most advanced solution
for HDMI and Video/DDC signal distribution. This CAT6 output port can be
easily connected to HDMI receiver’s CAT6 input and then to the display and
the HDMI output port can directly connected to the display. Each product in
this series is compatible to HDMI v1.3 specifi cations, which defi nes and support
to transfer Deep Color (10-bit and 12-bit) video and new lossless compressed
(Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio) digital audio, with
a high bandwidth up to 225MHz (6.75Gbps). Besides splitting and distributing,
the Video/DDC CAT6 output also does signal amplifi cation and equalization
which provide high performance I/O of audio and video.
2. Applications
 Home entertainment integration
 Multi-task project presentation
 Showroom Display
 Advertising display control
 System installation control
3. Package Contents
 1 x HDMI/CAT6 to HDMI/CAT6 Splitter Switcher
 5V DC power supply adaptor
 Operation Manual
4. System Requirements
 Input source equipment(s) with HDMI cable and or HDMI to CAT6 transmitter
 Output display(s) with HDMI cable and or CAT6 to HDMI receiver with
HDMI cable to display
1
1

5. Features
 HDMI 1.3, HDCP1.1 and DVI1.0 compliant.
 Deep color video up to 12bit, 1080p@(24/60)Hz.
 Supports One HDMI and one Video/DDC CAT6 source to One HDMI and
one Video/DDC CAT6 output simultaneously.
 HDCP keysets allows each output to work independently when
connecting to a HDMI display.
 Split the HDMI/CAT6 sources to HDMI/CAT6 outputs without signal loss.
 Supports LPCM7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
master audio transmission (32-192 kHz Fs sample rate).
 Supports a wide range of PC and HDTV resolutions from VGA to SXGA
and 480i to 1080p.
 Full HDCP Compliant.
 HDMI cable distance test with 1080p/8bits resolution the Input/Output
source can run up to 15/15 meters. The CAT6 cable test with 1080p/8bits
resolution the Input/Output source can run up to 45/45 meters.
HDMI cable distance test with 1080p/12bits resolution the Input/Output
source can run up to 15/10 meters. The CAT6 cable test with 1080p/12bits
resolution the Input/Output source can run up to 20/20 meters.
2
2

Frequency Bandwidth 2.25Gbps (single link)
Input Ports 1 x HDMI female port (Type A connector)
1 x CAT6 input Video/1 x CAT6 input DDC
Output Ports 1 x CAT6 output Video/1 x CAT6 output DDC
1 x HDMI female ports (Type A connector)
EDID STD / TV
HDMI Audio Output PCM2, 5.1, 7.1, Dolby 5.1, DTS 5.1, DD+, D-TrueHD,
DTS-HD
HDMI Cable In 1080p 8-bit (15M), 12-bit (15M)
HDMI Cable Out 1080p 8-bit (15M), 12-bit (10M)
CAT6 Cable In 1080p 8-bit (45M), 12-bit (20M)
CAT6 Cable Out 1080p 8-bit (45M), 12-bit (20M)
HDMI Resolution 480i, ~ 1080p 50/60, 1080p 24, VGA ~ SXGA
IR Frequency 20 ~ 60KHz
ESD Protection Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
Power Supply 5VDC/3.2A (US/EU standards, CE/FCC/UL certifi ed)
Dimensions (mm) 215(W) x123(D) x 30(H)
Weight(g) 365
Chassis Material Metal
Silkscreen Color Silver
Power Consumption 4.1W
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (non- condensing)
6. Specifi cations
3
Black
3
7. Operation Controls and Functions
The following sections describe the hardware components of the unit.
7.2 Front Panel
1 2 3 4 65
① HDMI/CAT6 input selection: Switch to select input sources either from
HDMI or CAT6.
② EDID Control Switcher: Default factory setting is TV, leave as if the display
is properly. Switch to STD to use built-in EDID.
[Note]:
1. When EDID switch to TV, the unit will detect the fi rst HDMI's output EDID and
record in the unit. If the fi rst detected HDMI output is DVI it will pass to next
output until the fi rst HDMI output detected.
The detection priority is HDMI v1.3 > HDMI v1.2 > DVI.
2. When EDID switch to STD the unit will use built-in EDID which supports:
Video →1080p 8-bit (max)
Audio →PCM 2CH
3. When EDID is switch to STD with input selection on HDMI or CAT6 IN the
display TV or monitor will switch to HDMI input 1, automatically. When EDID
is switch to TV regardsless of the input selection the display TV or monitor
will switch to HDMI input 1 mode. Therefore, it is not suggested to switch
the EDID to STD.
4. The EDID selection will only activate when the unit is re-plug and power on.
③ CEC output: When switch to HDMI ONLY, the HDMI output port’s CEC will
bypass the CEC commend directly to the HDMI and CAT6 input ports.
When switch to HDMI and CAT6, the HDMI and CAT6 output port’s CEC will
bypass the CEC commend cross to the HDMI .
④ HDMI Input: Connect input port to the HDMI or DVI output port of your
source equipment such as DVD player or set-top-box.
4

4
7. Operation Controls and Functions
The following sections describe the hardware components of the unit.
7.2 Front Panel
1 2 3 4 65
① HDMI/CAT6 input selection: Switch to select input sources either from
HDMI or CAT6.
② EDID Control Switcher: Default factory setting is TV, leave as if the display
is properly. Switch to STD to use built-in EDID.
[Note]:
1. When EDID switch to TV, the unit will detect the fi rst HDMI's output EDID and
record in the unit. If the fi rst detected HDMI output is DVI it will pass to next
output until the fi rst HDMI output detected.
The detection priority is HDMI v1.3 > HDMI v1.2 > DVI.
2. When EDID switch to STD the unit will use built-in EDID which supports:
Video →1080p 8-bit (max)
Audio →PCM 2CH
3. When EDID is switch to STD with input selection on HDMI or CAT6 IN the
display TV or monitor will switch to HDMI input 1, automatically. When EDID
is switch to TV regardsless of the input selection the display TV or monitor
will switch to HDMI input 1 mode. Therefore, it is not suggested to switch
the EDID to STD.
4. The EDID selection will only activate when the unit is re-plug and power on.
③ CEC output: When switch to HDMI ONLY, the HDMI output port’s CEC will
bypass the CEC commend directly to the HDMI and CAT6 input ports.
When switch to HDMI and CAT6, the HDMI and CAT6 output port’s CEC will
bypass the CEC commend cross to the HDMI .
④ HDMI Input: Connect input port to the HDMI or DVI output port of your
source equipment such as DVD player or set-top-box.
4

⑤ CAT6 IN: These slots are for connecting the Video/DDC input to the
Video/DDC output of the transmitter unit with CAT6 cables.
[Note]:
1. Cable tested with CAT-6E / 23AWG / Solid and therefore, cable with
different specifi cation may result in different distance.
2. Cable distance tested with equipment PS3 40G and 37" SamSung 12
bits LCD TV.
3. Figures provided in this manual are reference fi gures only, actual fi gures
may depend on source and display use with cable specifi cation.
⑥ DC 5V: This is the slot where you insert the 5V DC power supply for
electrical power before plugging the adaptor to an AC wall outlet.
7.1 Rear Panel
1 2
3
4
5
6
① CAT6 OUT: Connect the Video/DDC output to the Video/DDC input of
the receiver unit using CAT6 cables.
② HDMI OUT: Connect HDMI output port to the HDMI display.
③ HDCP indicators: When the input source is with the HDCP protection the
HDCP LED will illuminate.
④ SYNC Indicator: The LED will illuminate when the HDMI or DVI source had
been connected.
⑤ HDMI/CAT6 input indicator: The LED will illuminate when the HDMI or
CAT6 source is selected.
⑥ Link OUT: The LED will illuminate when the display had been connected.
5
5
8. RJ-45 Pin Defi nitions
Pin Video DDC
1 TX2+ DDC Bus Clock
2 TX2- NC
3 TX1+ DDC Bus Data
4 TX0+ Power 5V
5 TX0- GND
6 TX1- IR IN
7 TXC+ HPD
8 TXC- CEC
6

6
8. RJ-45 Pin Defi nitions
Pin Video DDC
1 TX2+ DDC Bus Clock
2 TX2- NC
3 TX1+ DDC Bus Data
4 TX0+ Power 5V
5 TX0- GND
6 TX1- IR IN
7 TXC+ HPD
8 TXC- CEC
6

30° 30°
3M 3M
7M
HD TV
HDMI
Cable
HDMI
HDMI
HDMI
HDMI
HDMI
HDMI
IR Receiver
DVD HDMI IN
IN OUT CAT6 OUTPUT
CAT6
OUTPUT
IR Blaster
IR Blaster
DVD
AorBorCAorBorC
x3
PU-22HC
PU-Q1H4C PU-Q1H8C
PU-106 Transmitter PU-1106 Transmitter
DDC
VIDEO
DDC
VIDEO
AorBorC
HDMI
HDMI
CAT6
OUTPUT
DVD
HD TV
DDC
VIDEO
PU-106 Transmitter PU-1106 Transmitter PU-Q1H4C PU-Q1H8C PU-O4H4C PU-22HC
DDCVIDEO
HDMI
HDMI
HDMI Cable
HDMI IN
CAT6 IN
9. Connection and Installation
7

ABC
HD TV
HDMI
Cable IR Receiver
HDMI
HDMI
30°
30°
3M 3M
7M
HD TV
HDMI
Cable IR Receiver
CAT6
OUTPUT CAT6
OUTPUT
HDMI
HDMI
30°
30°
3M 3M
7M
DDC
VIDEO
AorBorC
HD TV
HDMI
Cable
HDMI
HDMI
DDC
VIDEO
AorBorC
PU-106 PU-Q1C4H / PU-Q1C8H PU-22HC
8

Acronyms A
Acronym Complete Term
CAT6 Category 6 cable
DVI Digital Visual Interface
EDID Extended Display Identifi cation Data
HDCP High-Bandwidth Digital Content Protection
HDMI High-Defi nition Multimedia Interface
HDTV High-Defi nition Television
IR Infrared
LPCM Linear Pulse Code Modulation
STD Standard
SYNC Synchronize
SXGA Super Extended Graphics Array
VGA Video Graphics Array
99

10

11

12