CYP CPRO-U4H1HFS User manual

CPRO-U4H1HFS
UHD 4 to 1 HDMI Switcher
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2014 by Cypress Technology.
All Rights Reserved.
Version 1.0 May 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 25/03/15 Preliminary Release

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Remote Control................................5
6.4 RS-232 Pin Assignment .....................5
6.5 IP Searching Software Application
and Installation.......................................6
6.6 RS-232 & Telnet Commands............7
6.7 EDID Content....................................9
6.8 Telnet Control .................................10
6.9 WebGUI Control .............................12
7. Connection Diagram .......................... 14
8. Specications ...................................... 15
9. Acronyms ............................................. 17

1
1. INTRODUCTION
The 4 by 1 HDMI Switcher enables the switching of four HDMI sources
to a single HDMI output, allowing a display or AV Receiver to select
between four devices. With fast switching technology the device
can greatly eliminate the time required by swapping or turning ON/
OFF the connected displays. It supports 4K2K, 3D, 36-bit Deep Color,
Hi-Def. lossless audio and other features dened by the latest HDMI
specications. The management of source/sink scenarios can be
operated easily through on-panel buttons, IR remote control, RS-232,
Telnet and WebGUI control.
2. APPLICATIONS
• Home Theater/Entertainment
• Lecture Room/Hall Presentation
• Show Room/Demo Room
• Public Commercial Display
• Information Board
3. PACKAGE CONTENTS
• UHD 4 to 1 HDMI Switcher
• Remote Control with Battery
• IR Receiver Cable
• 5V/2.6A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-
Box and output HDMI TV/Display with connection cables.

2
5. FEATURES
• HDMI (with 3D & 4K2K supported) and HDCP compliant
• Select any one of four HDMI sources and display on a HDTV display
with fast switching between sources
• Supports 3D signals pass-through
• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30, 50/60
YUV_420 & 4096x2160@24, 50/60 YUV_420)
• Supports HDMI data rate from 300Mbps to 3Gbps and 'Deep Color'
up to 1080p/36-bit
• Supports selection of Standard (Fixed) or TV (Downstream) EDID
settings
• Supports Audio pass-through of High-denition Audio formats (LPCM
2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH, Dolby TrueHD and
DTS-HD Master Audio)
• HDMI inputs support ‘Standard’ and ‘Apple’ HDCP modes.
Selecting ‘Apple’ mode guarantees the compatibility of Apple
devices with this switcher
• Supports Telnet and WebGUI control

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWERSYNCINPUT 1234
UHD 4 TO 1 SWITCHER CPRO-U4H1HFS
1 2 3 4
1IR Window: This IR Receiver receives the remote control signal from
the packaged included remote control only with IR frequency at
38kHz.
2POWER & LED: Press this button to turn ON the device or set the
device to standby mode. The LED will illuminate in green when
switch to ON. This device contains power last memory and
therefore, when the power is connected the device will switch to
ON/Standby according to the last status.
*IP Reset: Press this button together with INPUT button for 3 second
under power ON status, when the LED blink for once it means IP
Reset complete.
3SYNC: This LED will illuminate when both input source and output
display are linked with active signal.
4IN 1~4: Press the INPUT button to select an input from the 4 input
sources, LED will illuminated according to the selection.

4
6.2 Rear Panel
1234
HDMI IN HDMI OUT SERVICECONTROL RS-232IR IN DC 5V
1 65432 7
1HDMI IN: Connect from source equipment such as Blu-ray/DVD/
PS3 players, Set-Top-Box or any HDMI equipped source device for
input signal sending. The device obtain auto detection function
and will detect the last plug-in source for display on output when
it is unplugged, the device will detect rotationally from 1~4 input
source for display on output.
2HDMI OUT: Connect to HDMI TV/display or HD Amplier for output
image and or audio display.
3SERVICE: This slot is reserved for rmware update use only.
4CONTROL: Connect from PC/Laptop with active internet service
for Telnet or WebGUI control with RJ-45 terminated cable.
5RS232: Connect from PC/Laptop for RS-232 command sending to
control the device.
6IR IN: Connect the IR Receiver included in the package for IR
signal receive from the included remote control.
7DC 5V: Connect the adaptor with power cord included in the
package and connect to AC wall outlet for power supply.

5
6.3 Remote Control
1POWER: Press this button to switch ON the
device or to set it to standby mode.
2INPUT: Press 1~4 to select input source.
6.4 RS-232 Pin Assignment
Switcher Remote Control
PIN Assignment PIN Assignment
1 NC 1 NC
2Tx 2Rx
3Rx 3Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
CR-72
POWER
INPUT
34
12
1
2

6
6.5 IP Searching Software Application and Installation
Please download the software from www.cypress.com.tw with le
name CDPS V2.000 and save it in a directory where you may use it
later.
Connect the Control System with PC/Laptop through the Ethernet
port through an active network system and open the CDPS V2.000
application. Click on Find Devices on Network and a list of the devices
connected to the Control System will show up.
Then user may use the IP Address to nd the control device through
Telnet, WebGUI or even RS-232/Hyper Terminal tools.

7
6.6 RS-232 & Telnet Commands
COMMAND NAME DESCRIPTION DESCRIPTION OF
PARAMETER
P0 Power Off (Standby) NONE
P1 Power On NONE
A N Select Input N N=1-4
IPCONFIG Display The Current IP
Congure
NONE
SIPADDR XXX.XXX.
XXX.XXX
Set Ethernet IP
Address
XXX=0~255
SNETMASK XXX.XXX.
XXX.XXX
Set Ethernet Net Mask XXX=0~255
SGATEWAY XXX.XXX.
XXX.XXX
Set Ethernet
Gateway
XXX=0~255
HTTPPORT N Set Http Port Number N=0~65535
RSTIP IP Conguration
Reset To <DHCP>
NONE
EDIDMODE Show EDID Mode NONE
EDIDMODE N Set EDID Mode N=0(Appoint), 1(All)
EDIDALL Show EDID Mode
Source For All
NONE
EDIDALL N Set EDID Mode
Source For All
N=1-9 (ref. EDID All)
EDIDIN Show Input EDID
Source
NONE
EDIDIN N1 Show Input N1 EDID
Source
N1=1-4
EDIDIN N1 N2 Set Input N1 EDID
Source
N1=1-4 N2=1-9 (ref.
EDID All)
HDCPIN Input HDCP Status NONE
HDCPIN N1 Show Input N1 HDCP
Status
N1=1-4

8
COMMAND NAME DESCRIPTION DESCRIPTION OF
PARAMETER
HDCPIN N1 N2 Set Input N1 HDCP
On/Off*
N1=1-4 N2=0(OFF),
1(ON)
SOURCEDET Show All Inputs Signal NONE
SOURCEDET N1 Show Input N1 Signal N1=1-4
SINKINFO Show Output
Information
NONE
INNAME Show Input Name NONE
INNAME N1 N2 Set Input Name N1=1-4
N2=ABCDEFGH(Max
Length=8)
OUTNAME Show Output Name NONE
OUTNAME A N1 Set HDMI Output
Name
N1=ABCDEFGH(Max
Length=8)
VER Show Unit Firmware
Version
NONE
REBOOT System Reboot NONE
HELP (?)Show Command List NONE
HELP N Show Descript Of
Command
N : COMMAND NAME
FADEFAULT All Congure Set To
Factory Default
NONE
Note:
1. All the RS-232 command will be not executed unless followed with
a carriage return. Commands are case-sensitive.
2. *HDCP ON/OFF equivalent to HDCP standard and Apple mode.
3. P address's default setting is on statics with 192.168.1.50
4. To nd IP address in your zone an easy application is provided,
please download it from http://zh-tw.cypress.com.tw/uploadle/
CDPS_20140806_v2000.zip

9
6.7 EDID Content
EDID
Mode
Mode Selection Description
EDID All
HDMI Output(TV) HDMI Output display EDID
8/2D/PCM/720p
Build-In EDID, Deep
color/2D3D/audio/native
resolution
8/2D/PCM/
AC3/720p Same as above
8/2D/PCM/1080p Same as above
8/2D/PCM/
AC3/1080p Same as above
8/2D/PCM/4K2K Same as above
8/2D/PCM/
AC3/4K2K Same as above
8/2D/PCM/Y420 Same as above
8/2D/PCM/AC3/
Y420 Same as above
EDID
Appoint
EDID IN1 Input 1’s EDID
EDID IN2 Input 2’s EDID
EDID IN3 Input 3’s EDID
EDID IN4 Input 4’s EDID
Note:
1. EDID function only selectable under RS-232 and WebGUI control.
2. When power supply is re-plugged from the device the EDID mode
will switch to EDID All- HDMI OUTPUT.

10
6.8 Telnet Control
To access the telnet control under MS windows, click ‘Start’ menu and
type “cmd” in the search eld then press enter.
Under Mac OS X, go to Go → Application → Utilities → Terminal
See below for reference.
Once in the command line interface (CLI) type "telnet", then the IP
address, and hit enter.

11
Press “Help” or “?” then hit enter to bring up all available commands.
Note: Any commands will not be executed unless followed by a
carriage return. Commands are case-insensitive. If the IP is changed
then the IP Address required for Telnet access will also change
accordingly.

12
6.9 WebGUI Control
On a PC/Laptop that is connected to an active network system, open
a web browser and type device’s IP address (the default statics IP is
192.168.1.50 or available from RS-232 or use the link application from
note 4 in section 6.5 to nd) on the web address entry bar. The browser
will display the device’s Status, IO Status, EDID Control, Settings and
Network Conguration control pages for users to control.
Click on EDID Control for EIDID selections.
Click on Settings to set each input’s HDCP Control and Preset
Conguration. HDCP Enable and Disable equivalence to HDCP
standard and Apple mode.

13
Click on Network Conguration to set the device’s IP conguration
once the changes is saved the system will reset the IP address on the
device automatically and user will need to re-enter the IP address to
continue the WebGUI function.

14
7. CONNECTION DIAGRAM
1234
HDMI IN HDMI OUT SERVICE CONTROLRS-232 IR IN DC 5V
CR-72
POWER
INPUT
34
12
6m 6m
30°
5m
PC NB
Blu-ray/DVD/PS3 Players
Display TV/Monitor
OR
Note: The IR Extender cable distance is up to 5 meters and 8 meters for
the IR Window on the front panel.

15
8. SPECIFICATIONS
Frequency bandwidth 300Mbps to 3Gbps
Input Ports 4 x HDMI, 1 x USB (Service only), 1 x RJ45
(Control), 1 x RS-232, 1 x IR Extender
Output ports 1 x HDMI
Resolution 480i~1080p@50/60, 1080p@24, 4K2K
(3840x2160@24/25/30, 50/60 YUV_420 &
4096x2160@24, 50/60YUV_420)
HDMI I/O Cable Distance 15M@8/12bit, 5M@4Kx2K
IR Frequency 30~50kHz
Power Supply 5VDC/2.6A (US/EU standards, CE/FCC/UL
certied)
ESD Protection Human Body model:
± 8kV (air-gap discharge)
± 4kV (contact discharge)
Dimensions 240mm (W) x 104mm (D) x 43mm (H)/
Jacks Excluded
240mm (W) x 111.2mm (D) x 48mm (H)/
Jacks Included
Weight 798g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0˚C~40˚C / 32˚F ~ 104˚F
Storage temperature -20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (no condensation)
Power Consumption 4W