Cypress PSoC CY8CKIT-048 User manual

CY8CKIT-048 QUICK START GUIDE
PSOC®ANALOG COPROCESSOR PIONEER KIT
• The on-board RGB LED will turn on with
red color
• Connect the board to your PC using the provided
USB cable
Note: This demo does not require driver
installation, although this may continue in the
background
1
R
Kit Contents:
1. PSoC Analog Coprocessor Pioneer board
2. USB Standard-A to Mini-B cable
3. Four jumper wires (4 inches each)
4. Five connectors (one10x1, two 8x1,
one 6x1 and one 4x1)
5. One metal disk
6. Quick Start Guide (this document)
2

CY8CKIT-048 QUICK START GUIDE
• Control the intensity of the RGB LED by bringing
your nger close to the Ambient Light Sensor (ALS)
Note 1: Bringing your nger close to the ALS
(do not touch the sensor) obstructs the light falling
on the sensor.
Note 2: To observe the change in RGB LED intensity,
keep the board in a location with good ambient
light illuminance.
• To get started, download and install the
PSoC CreatorTM IDE, PSoC Analog Coprocessor
Pioneer Kit code examples, documents and
hardware design les from
www.cypress.com/CY8CKIT-048
Jumpers/Switches Default Position
Jumper/Switch
J9 System Power (VDD Voltage)
Selection 1-2
1-2
REG
DIGITAL
3-4
Shunt Selection for
Current Measurement
Humidity Sensor
Calibration
VDD Source Selection
Power Domain
Monitor Selection
J14
J17
SW4
SW5
Purpose Default Position
3 4

CY8CKIT-048 QUICK START GUIDE
1. PSoC Analog Coprocessor (CY8C4A45LQI-483, U1)
2. PSoC Analog Coprocessor reset button (SW1)
3. ArduinoTM Uno shield compatible power and I/O headers
(J1, J2, J3, J4)
4. PSoC Analog Coprocessor 5-pin program and debug test points
5. PSoC Analog Coprocessor 10-pin program and debug
header (J13)
6. User button (SW2)
7. KitProg2 custom application/programming header (J11)
8. KitProg2 I/O header (J16)
9. External power supply connector (J15)
10. KitProg2 USB Mini-B connector (J10)
11. Power LED (LED4)
12. KitProg2 status LEDs (LED1, LED2, LED3)
13. Cypress F-RAM 1 Mb (FM24V10-G, U10)
14. Voltage Level Translator for F-RAM (U9)
15. KitProg2 (PSoC 5LP) programmer and debugger
(CY8C5868LTI-LP039, U2)
16. Voltage regulator circuit
17. Cypress PMIC (MB39C011APFT-G-BND-ERE1, U3)
18. System Power (VDD) selection jumper (J9)
19. Arduino ICSP compatible header (J12)
20. Power domain selection switch for current
measurement (SW5)
21. VDD source selection switch (SW4)
22. PIR Motion Sensor (ZRE200GE, U7)
23. Thermistor (B57164K103J, RT1)
24. Humidity Sensor (HPP801A031, H1)
25. Ambient Light Sensor (TEMD6200FX01, D4)
26. Humidity Sensor calibration jumper (J17)
27. Inductive Proximity Sensor (U11)
28. Current measurement jumper (J14)
29. KitProg2 user button (SW3)
30. RGB LED (LED5)
31. 32.768 kHz crystal oscillator (Y1)
PSoC Analog Coprocessor Pioneer Board Details
12
334 5
6
13 15 16 17 318 31 19 20 21
22
23
24
25
26
27
7
8
9
10
11
12
30 29 28
14

PSoC Analog Coprocessor Pioneer Board Pinout Description
© 2016 - 2017 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the property of their respective owners.
002-11173 Rev.*D
CY8CKIT-048 QUICK START GUIDE
PSOC®ANALOG COPROCESSOR PIONEER KIT
SWDIO
SWDCLK
RESET
GND
VTARG
NC IOREF/NC RESET/RESET 3.3 V/V 3.3 5 V/V 5.0 GND/GND GND/GND Vin/VIN
SCL/P4_0 SDA/P4_1 AREF/NC GND/GND D13/NC D12/NC D11/NC D10/NC D9/NC D8/NC
D7/NC D6/NC D5/NC D4/NC D3/NC D2/NC D1/P0_4 (RX) D0/P0_5 (TX)
NC
PAC_VDD/IOREF
RESET/RESET
V 3.3/3.3 V
V 5.0/5 V
GND/GND GND/GND
VIN/Vin
P4_0/SCL
P4_1/SDA
P1_3/AREF
GND/GND
P0_6/D13 P0_5/D12 P0_4/D11 P0_7/D10
P1_7/D9 P2_4/D8
P2_7/D7 P1_0/D6 P1_1/D5 P1_2/D4 P2_3/D3 P1_5/D2 P0_5/D1 P0_4/D0
P3_0/A0 P3_1/A1 P3_2/A2 P3_3/A3 P3_4/A4 P3_7/A5
P2_6 P2_5 P2_1 P3_5
A0/P0_2 A1/P0_3 A2/NC A3/P1_6 A4/P1_4 A5/P3_6 NC P2_2 P2_0 NC
NC
P5LP0_1
P5LP12_0
P5LP3_0
P5LP12_1
P5LP3_5
P5LP12_6
GND
P5LP15_4
P5LP1_6
P5LP0_7
P5LP0_3
P5LP0_2
P5LP_SWDIO
P5LP_SWDCLK
P5LP_XRES
GND
P5LP_VBUS
P5LP_VDD
P5LP15_1
P5LP15_2
P5LP15_3
P5LP12_5
P5LP3_4
P5LP12_7
P5LP3_6
Arduino Uno R3
PSoC Analog Coprocessor Pioneer board