D-Link DCH-112 User manual

DCH-112 Door/ Window Sensor
The DCH-112 has door/window sensor function in one, based on Z-
WaveTM technolog .
It is the Z-WaveTM plus product, it support the securit , OTA... Those
newest features of the Z-WaveTM technolog . Z-WaveTM is a wireless
communication protocol designed for home automation, specificall to
remotel control applications in residential and light commercial
environments. The technolog uses a low-power RF radio embedded or
retrofitted into home electronics devices and s stems, such as lighting,
home access control, entertainment s stems and household appliances.
This product can be included and operated in an Z-WaveTM network
with other Z-WaveTM certified devices from other manufacturers and/or
other applications. All non-batter operated nodes within the network
will act as repeaters regardless of vendor to increase reliabilit of the
network.
The device adopt the Z-WaveTM 500 series chip, when our Z-WaveTM
network s stem is all made b Z-WaveTM 500 series devices. The
network s stem will have the advantages as below.
•Concurrent multi-channel support reduces external interference.
•Better RF range, improve about 10 meters in indoor.
•Support 100 Kbps transmit speed, speed up communication.
Add to/Remove from Z-WaveTM Network
There are two tamper ke s in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-WaveTM network.
In the first time, add the device into the Z-WaveTM network. First,
make sure the primar controller is in the add mode. And then power
on the device, just take out the insulation M lar in the back side of the
device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.
Notice: Including a node ID allocated b Z-WaveTM Controller means
“Add” or “ nclusion”. Excluding a node ID allocated b Z-WaveTM
Controller means “Remove” or “Exclusion”.
Function Description
Add 1. Have Z-WaveTM Controller entered inclusion mode.
2. Pressing tamper ke three times within 1.5 seconds
to enter the inclusion mode.
3. After add successful, the device will wake to
receive the setting command from Z-WaveTM
1

Controller about 20 seconds.
Remove
1. Have Z-WaveTM Controller entered exclusion mode.
2. Pressing tamper ke three times within 1.5 seconds
to enter the exclusion mode.
Node ID has been excluded.
Reset
Notice: Use this procedure only in the event
that the primary controller is lost or
otherwise inoperable.
1. Pressing tamper ke four times within 1.5 seconds
and do not release the tamper ke in the 4th
pressed, and the LED will light ON.
2. After 3 seconds the LED will turn OFF, after that
within 2 seconds, release the tamper ke . If
successful, the LED will light ON one second.
Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to
factor default.
Association
1. Have Z-WaveTM Controller entered association
mode.
2. Pressing tamper ke three times within 1.5 seconds
to enter the association mode.
Note: The device support 2 groups. The group 1 is for
receiving the report message, like triggered event,
temperature, illumination etc. The group 2 is for light
control, the device will send the “Basic Set” command
to this group. And each group support 8 nodes
maximum.
•Failed or success in add/remove the node ID can be viewed
from Z-WaveTM Controller.
Notice 1: Alwa s RESET a Z-WaveTM device before tr ing to add it to a
Z-WaveTM network
Notice 2: When the device into NWI mode, the sensor functionalit
will useless. The NWI mode will timeout after 30 seconds. You can
press the tamper ke 3 times to abort the NWI mode.
Z-WaveTM Notification
After the device adding to the network, it will wake-up once per da in
default. When it wake-up it will broadcast the “Wake Up Notification”
message to the network, and wake-up 10 seconds for receive the
setting commands.
The wake-up interval minimum setting is 30 minutes, and maximum
setting is 120 hours. And the interval step is 30 minutes.
If the user want to wake-up the device immediatel , please remove the
front cover, and press the tamper ke once. The device will wake-up 10
seconds.
Z-WaveTM Message Report
When the door/windows triggered, the device will report the trigger
event and also report the batter status, temperature and illumination
level.
In default the device will using Notification Report to represent the
trigger event, it can be changed to Sensor Binar Report b setting the
configuration NO. 7 Bit4 to 1.
Notification Report (V4)
Notification T pe: Home Securit (0x07)
Event: Motion Detection, Unknown Location (0x08)
Sensor Binar Report (V2)
Sensor T pe: Motion (0x0C)
Sensor Value: 0xFF
2

* Door/Window Report:
When the door/window state changed, the device will unsolicited to
send the report to the nodes in the group 1.
Notification Report (V4)
Notification T pe: Access Control (0x06)
Event: Door/Window is open (0x16)
Door/Window is closed (0x17)
Sensor Binar Report (V2)
Sensor T pe: Door/Window (0x0A)
Sensor Value: 0x00 is closed, 0xFF is opened.
* Tamper Report:
Both the 2 tamper ke s are pressed over 5 seconds. The device will
into the alarm state. In that state, if an one of the tamper ke s be
released, the device will unsolicited to send the report to the nodes in
the group 1.
Notification Report (V4)
Notification T pe: Home Securit (0x07)
Event: Tampering. Product covering removed (0x03)
Sensor Binar Report (V2)
Sensor T pe: Tamper (0x08)
Sensor Value: 0xFF
In the default, when the temperature is changed to plus or minus one
degree Fahrenheit (0.56 degree Celsius), the device will report
temperature information to the nodes in the group 1.
The device will measure the temperature in ever one minute. And if
the temperature is over 140 degree Fahrenheit (60 degree Celsius), the
device will alwa s report in each measurement.
* Timing Report:
Beside the event triggered could report message, the device also
support the timing unsolicited report of the status.
•Batter level report: Ever 6 hours report once in default.
It could be changed b setting the configuration NO. 10.
•Low batter report: When the batter level is too low, ever 30
minutes will report once.
•Door/window state report: Ever 6 hours report once in default.
It could be changed b setting the configuration NO. 11.
•Illumination level report: Ever 6 hours report once in default.
It could be changed b setting the configuration NO. 12.
•Temperature report: Ever 6 hours report once in default.
It could be changed b setting the configuration NO. 13.
Notice: The configuration NO. 10, 11, 12 and 13 could be setting to
zero to disable the auto report. And the configuration NO. 20 could
change the tick interval, the default value is 30, if setting to 1, that
means the minimum auto report interval will be one minute. And please
notice if setting this value to zero, that means disable all of the timing
report except the low batter detection.
Power Up Procedure
* Battery Power Check
When the device power up, the device will detect the power level of the
batter immediatel . If the power level is too low, the LED will continue
flash about 5 seconds. Please change another new batter .
* NW
When the device power on, the device will check is it alread adding to
the network? If doesn't, it will auto start the NWI mode. The LED will
flash in ever second and continue 30 seconds. Until timeout or the
device successful to inclusion b controller. The use can presses the
tamper ke 3 times to abort the NWI mode.
3

* Wake
When the device power on, the device will wake about 20 seconds. In
this duration, the controller can communicate with the device. Normall
the device is alwa s sleeping to save the batter energ .
Security Network
The device support the securit function. When the device included
with a securit controller, the device will auto switch to the securit
mode. In the securit mode, the follow commands need using Securit
CC wrapped to communicate, otherwise it will not response.
COMMAND_CLASS_BATTERY
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_SENSOR_BINARY_V2
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
COMMAND_CLASS_WAKE_UP_V2
Operation Mode
There are two modes “Test” and “Normal”.
“Test Mode” is for the user test the sensor function when installation.
“Normal Mode” for the normal operation.
When the event triggered, normall the LED won't indicated, unless the
batter is in the low level, the LED will flash once. But in the “Test
Mode” the LED also will light ON one second.
When the event triggered, the device will report the messages to the
nodes in the group 1. The messages also include the batter level, the
temperature and the illumination level. The user can switch the report
b setting the configuration NO. 5 bit4 (illumination) and bit5
(temperature), and the configuration NO. 7 bit6 (batter ).
When the event triggered, if the environment luminance is less than
the setting of the value of the configuration NO. 4, the device will emit
the signal to turn ON the lighting equipment, those nodes are in the
group 2. And dela a while to turn OFF the lighting equipment. The
dela time is setting b the configuration NO. 9.
Notice: When the tamper ke of the back side is released, the device
alwa s in the “Test Mode”, no matter the DIP switch setting.
Battery nstallation
When the device report the low batter message. The user should
replace the batter to new one. The batter t pe is CR123A, 3.0V.
The wa to open the front cover please follow below steps.
1. Using a tool to press the 1-1 position, to release the cover.
2. Hold the front cover and pull back
3. Hold the front cover and pull up
Replace the new batter and install the cover back.
4

1. Put the front cover bottom to 1-1, and press down.
2. Push the front cover top to 2-1.
Choosing a Suitable Location
1. The recommended mounting height is 160cm
2. Don't let the device facing the window or the sunlight.
3. Don't let the device facing the source of heat. For instance the
heater or the air-condition.
nstallation
1. In the first time, add the device into the Z-WaveTM network. First,
make sure the primar controller is in the inclusion mode. And then
power on the device, just take out the insulation M lar in the back side
of the device. The device will auto start the NWI (Network Wide
Inclusion) mode. And it should be included in 5 seconds. You will see
the LED light ON one second.
2. Let the controller associate with the device into the first group, an
light switch that intend to be turned on when the device trig please
associate with the device into the second group.
3. In the accessor pack. There are two t pe of double coated tape,
one is thicker (hereinafter referred to as A tape) and another is thinner
(hereinafter referred to as B tape), ou can use A tape for the test at
the beginning. The right wa for A tape installation is stick it to the
position below tamper ke . The thicker tape won't let the tamper ke
pressed, so the sensor will enter the test mode, You ma test if
installed position is good or not b this wa .
After finish the test and decide to fix, then ou can remove tape A, and
mounting the sensor b using tape B. The tamper ke will pressed and
let the sensor enter normal mode.
Z-Wave Configuration Settings
Notice:
* All of the configuration, the data size is 1.
* The configuration mark with star(*), means after the remove the setting
still keep, don't reset to factor default. Unless the user execute the
“RESET” procedure.
* The reserve bit or not supported bit is allowed an value, but no effect.
5

NO
.Name Def. Vali d A B C Description
2Basic Set
Level 0xFF All   
Setting the BASIC command value to
turn on the light. The 0xFF(-1) means
turn on the light. For dimmer
equipment 1 to 100 means the light
strength.
0 means turn off the light.
Caution: The value is unsigned b te,
the range is from 0x00 ~ 0xFF.
5
(*)
Operation
Mode 0All
Operation mode. Using bit to control.
Caution: The value is unsigned b te,
the range is from 0x00 ~ 0xFF.
0Bit0: Reserve.
0  
Bit1: 1 means test mode,
0 means normal mode.
Notice:
This bit onl effect b the DIP Switch
setting to “customer mode”, otherwise
it decides b DIP Switch setting to
Test or Normal Mode.
0Bit2: Disable the door/window
function. (1:Disable, 0:Enable)
0Bit3: Setting the temperature scale.
0: Fahrenheit, 1:Celsius
0Bit4: Disable the illumination report after event triggered. (1:Disable,
0:Enable)
0Bit5: Disable the temperature report
after event triggered. (1:Disable,
0:Enable)
NO
.Name Def. Vali d A B C Description
0Bit6: Reserve.
0Bit7: Disable the back ke release into test mode. (1:Disable,
0:Enable)
7
(*)
Customer
Function
4All
Customer function switch, using bit
control.
Caution: The value is unsigned b te,
the range is from 0x00 ~ 0xFF.
0Bit0: Reserve.
0Bit3: Disable send out BASIC OFF after door closed. (1:Disable,
0:Enable)
0Bit4: Notification T pe, 0: Using Notification Report.
1: Using Sensor Binar Report.
0Bit5: Disable Multi CC in auto report. (1:Disable, 0:Enable)
0Bit6: Disable to report batter state when the device triggered. (1:Disable,
0:Enable)
0Bit7: Reserve.
10
Auto
Report
Batter
Time
12 0 ~
127   
The interval time for auto report the
batter level.
0 means turn off auto report batter .
The default value is 12. The tick time
can setting b the configuration No.20.
11 Auto Report 12 0 ~ The interval time for auto report the
6

NO
.Name Def. Vali d A B C Description
Door/Windo
w State
Time
127
door/window state.
0 means turn off auto report
door/window state.
The default value is 12. The tick time
can setting b the configuration No.20.
12
Auto Report
Illumination
Time
12 0 ~
127   
The interval time for auto report the
illumination.
0 means turn off auto report
illumination.
The default value is 12. The tick time
can setting b the configuration No.20.
13
Auto Report
Temperatur
e Time
12 0 ~
127   
The interval time for auto report the
temperature.
0 means turn off auto report
temperature.
The default value is 12. The tick time
can setting b the configuration No.20.
20
Auto Report
Tick
Interval
30 0 ~
0xFF   
The interval time for auto report each
tick. Setting this configuration will
effect configuration No.10, No.11,
No.12 and No.13.
The unit is 1 minute.
Caution1: Setting to 0 means turn
off all auto report function.
Caution2: The value is unsigned
b te, the range is from 0x00 ~ 0xFF.
Z-Wave Supported Command Class
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_SENSOR_BINARY_V2
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_MULTI_CMD
COMMAND_CLASS_SECURITY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Specifications
Power b CR123A lithium batter .
Signal (Frequenc ):
DCH-112: 868.40 MHz, 869.85 MHz(EU),
DCH-112: 908.40 MHz, 916.00 MHz(US),(Canada)
DCH-112: 922~927 MHz(JP/TW),
DCH-112: 921.40 MHz, 919.80 MHz(ANZ),
Range:
Minimum 40 meters indoor,
100 meters outdoor line of sight.
Operating Temperature: -10oC ~ 40oC
For indoor use onl .
Specifications subject to change without notice due to continuing
product improvement.
7

FCC D: KA2CHZ112A1
C D: 4216A-CHZ112A1
Disposal
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, rec cle it
responsibl to promote the sustainable reuse of material
resources. To return our used device, please use the
return and collection s stems or contact the retailer where
the product was purchased. The can take this product for
environmental safe rec cling.
Compan of License Holder：Philio Technolog Corporation
Address of License Holder：8F., No.653-2, Zhongzheng Rd., Xinzhuang
Dist., New Taipei Cit 24257, Taiwan(R.O.C)
FCC nterference Statement
This equipment has been tested and found to compl with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequenc energ and, if not installed and
used in accordance with the instructions, ma cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined b turning the equipment off and
on, the user is encouraged to tr to correct the interference b one of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device ma not cause harmful interference, and
(2) This device must accept an interference received, including
interference that ma cause undesired operation.
FCC Caution: An changes or modifications not expressl approved b
the part responsible for compliance could void the user's authorit to
operate this equipment.
This transmitter must not be co-located or operating in conjunction
with an other antenna or transmitter.
Warning
Do not dispose of electrical appliances as unsorted municipal waste,
use separate collection facilities. Contact our local government for
information regarding the collection s stems available. If electrical
8

appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging
our health and well-being.
When replacing old appliances with new once, the retailer is legall
obligated to take back our old appliance for disposal at least for free
of charge.
9