D-Link DAP-1320 Manual

-1-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
FAQ : How To connect Range Extender to existing router via
WPS Setup
Release date : 1/06/2015
Model Support : DAP-1320
H/W:A1 , B1
S/W:1.x , 2.x

-2-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
*Firmware 1.10 and higher
DAP-1320 Push Button WPS Configuration
Note : DAP-1320 WPS router/access point 

1 : DAP-1320 
Note : 

-3-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00

-4-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
2 : WPS router/AP 5-7 
3 : WPS DAP-1320 2LED 
LED 

-5-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
4 : 
Note: DAP-1320 


-6-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
5 : DAP-1320 
SSID configuration note 


-7-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
*Firmware 1.10 and higher
DAP-1320 Push Button WPS Configuration
Note: In order to setup the DAP-1320 using WPS, you must have a WPS compatible
router/access point
Step 1: Plug in the DAP-1320
Note: The light should turn red and then start blinking orange

-8-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Step 2: Press the WPS button on your router/AP (usually for about 5-7 seconds)
Step 3: Press and hold the WPS button on the DAP-1320 for 2 seconds. The LED should start to blink
green. Once it makes connection with your router the LED will stop flashing and turn solid GREEN.

-9-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Step 4: Unplug and place the DAP-1320 approx half way between the router and the desired
connection area.
Note: Correct placement of the DAP-1320 is very important. It needs to be positioned in an area
that still receives good signal from your router. A good starting point is approx half way between
the router and the area you want to get signal to.
Step 5: To connect wireless to the DAP-1320, Scan for available wireless networks on your wireless
device and connect using the Wi-Fi Network Name (SSID) and Wi-Fi Password information located on
your configuration note.

-10-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Setup is Complete.
Back to Top

-11-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
ฝ่ ายสนับสนุนทางด้านเทคนิค
Call Center หมายเลขโทรศัพท์ 02-6617997
ภาษาไทย : จันทร์ ถึง ศุกร์ เวลา 9.00 น. –18.00 น.
Thai : Mon –Fri : Time 9.00 –18.00.
ภาษาอังกฤษ : เสาร์ , อาทิตย์ , วันหยุดนขัตฤกษ์ และ วันธรรมดา หลัง 18.00 น.
English : Sat –Sun , Public Holiday and after 18.00 weekday.
Website : www.dlink.co.th
email: [email protected].sg
Facebook : http://www.facebook.com/DLinkThailandFans

-12-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Nationwide D-Link Service Centres :