D-Link DWR-980 User manual

Quick Installation Guide
DWR-980
Wireless AC1200 4G LTE Router with VDSL2 Support,
Gi abit Ethernet Ports, and 2 FXS Ports

DWR-980 Quick Installation Guide
BEFORE YOU BEGIN
Delivery Package
•Router DWR-980
•Power adapter DC 12V/2.5A
•Ethernet cab e
•Two detachab e LTE/3G antennas
•RJ-11 te ephone cab e
•“Quick Installation Guide” (brochure).
If any of the items are missing, p ease contact your rese er.
The “User Manual” and “Quick Installation Guide” documents are avai ab e
on D-Link website (see www.d ink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2

DWR-980 Quick Installation Guide
Default Settings
Do ain na e of device dlinkrouter.local.
IP address of device 192.168.0.1
Userna e (login) admin
Password admin
Na e of wireless
network (SSID)
2.4GHz DWR-980
5GHz DWR-980-5G
Network key (PSK password)
see WPS PIN on the barcode
abe on the back pane of
the device
!
Router DWR-980 with defau t settings cannot connect to the Internet.
To get started, p ease set your own password for access to the web-
based interface and change the WLAN name (SSID); then, if needed,
configure other settings recommended by your ISP.
3

DWR-980 Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the router:
◦App e Safari 8 and ater
◦Goog e Chrome 48 and ater
◦Microsoft Internet Exp orer 10 and ater
◦Microsoft Edge 20.10240 and ater
◦Mozi a Firefox 44 and ater
◦Opera 35 and ater.
•A NIC (Ethernet or Wi-Fi adapter) to connect to the router.
•An 802.11a, b, g, n, or ac Wi-Fi adapter to create a wire ess network.
•Ana og phone.
•An active SIM card (when it is necessary to connect to the Internet via
mobi e operators' networks)1.
1 Contact your operator to get information on the service coverage and fees.
4

DWR-980 Quick Installation Guide
CONNECTING TO PC
PC with Ethernet Adapter
1. Connect an Ethernet cab e between any of LAN ports ocated on the back
pane of the router and the Ethernet port of your PC.
2. To connect via built-in modem: insert a SIM card into the s ot on the eft
side pane of the router with the go d contacts facing towards the front of
the device and gent y push unti it c icks.
!If you need to connect a SIM card or change it to another one when the
router is powered on, power off the router, insert or change the SIM
card, and power on the router.
3. To connect the router to a DSL line: connect a phone cab e between the
phone jack and the DSL port of the router.
4. To connect the router to an Ethernet line: connect an Ethernet cab e
between the WAN port of the router and the Ethernet ine.
5. Connect another phone cab e between an FXS port of the router and the
phone.
6. Connect the power cord to the power connector port on the back pane of
the router, then p ug the power adapter into an e ectrica out et or power
strip.
7. Turn on the router by moving the POW R switch on its back pane to the
ON (I) position.
Then make sure that your PC is configured to obtain an IP address
automatica y (as DHCP c ient).
5

DWR-980 Quick Installation Guide
Obtaining P Address Automatically
(OS Windows 7)
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the Network and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Local Area Connection
icon and se ect the Properties ine in the menu disp ayed.
5. In the Local Area Connection Properties window, on the
Networking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
6

DWR-980 Quick Installation Guide
6. Make sure that the Obtain an IP address auto atically and Obtain
DNS server address auto atically choices of the radio buttons are
se ected. C ick the OK button.
7. C ick the OK button in the connection properties window.
7

DWR-980 Quick Installation Guide
PC with Wi-Fi Adapter
1. To connect via built-in modem: insert a SIM card into the s ot on the eft
side pane of the router with the go d contacts facing towards the front of
the device and gent y push unti it c icks.
!If you need to connect a SIM card or change it to another one when the
router is powered on, power off the router, insert or change the SIM
card, and power on the router.
2. To connect the router to a DSL line: connect a phone cab e between the
phone jack and the DSL port of the router.
3. To connect the router to an Ethernet line: connect an Ethernet cab e
between the WAN port of the router and the Ethernet ine.
4. Connect another phone cab e between an FXS port of the router and the
phone.
5. Connect the power cord to the power connector port on the back pane of
the router, then p ug the power adapter into an e ectrica out et or power
strip.
6. Turn on the router by moving the POW R switch on its back pane to the
ON (I) position.
7. Make sure that the Wi-Fi adapter of your PC is on. As a ru e, modern
notebooks with bui t-in wire ess NICs are equipped with a button or
switch that turns on/off the wire ess adapter (refer to your PC documents).
If your PC is equipped with a p uggab e wire ess NIC, insta the software
provided with your Wi-Fi adapter.
Then make sure that your Wi-Fi adapter is configured to obtain an IP address
automatica y (as DHCP c ient).
8

DWR-980 Quick Installation Guide
Obtaining P Address Automatically and
Connecting to Wireless Network (OS Windows 7)
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the Network and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Wireless Network
Connection icon. Make sure that your Wi-Fi adapter is on, then se ect
the Properties ine in the menu disp ayed.
5. In the Wireless Network Connection Properties window, on the
Networking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
9

DWR-980 Quick Installation Guide
6. Make sure that the Obtain an IP address auto atically and Obtain
DNS server address auto atically choices of the radio buttons are
se ected. C ick the OK button.
7. C ick the OK button in the connection properties window.
8. To open the ist of avai ab e wire ess networks, se ect the icon of the
wire ess network connection and c ick the Connect To button or eft-
c ick the network icon in the notification area ocated on the right side of
the taskbar.
10

DWR-980 Quick Installation Guide
9. In the opened window, in the ist of avai ab e wire ess networks, se ect the
wire ess network DWR-980 (for operating in the 2.4GHz band) or
DWR-980-5G (for operating in the 5GHz band) and c ick the Connect
button.
10. In the opened window, enter the network key (see WPS PIN on the
barcode abe on the back pane of the device) in the Security key fie d
and c ick the OK button.
11. Wait for about 20-30 seconds. After the connection is estab ished, the
network icon wi be disp ayed as the signa eve sca e.
!
If you perform initia configuration of the router via Wi-Fi connection,
note that immediate y after changing the wire ess defau t settings of the
router you wi need to reconfigure the wire ess connection using the
new y specified settings.
11

DWR-980 Quick Installation Guide
CONFIGURING ROUTER
Connecting to Web-based nterface
Start a web browser. In the address bar of the web browser, enter the domain
name of the router (by defau t, dlinkrouter.local) with a dot at the end
and press the nter key. A so you can enter the IP address of the device (by
defau t, 192.168.0.1).
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to remote server ”) occurs upon connecting to
the web-based interface of the router, make sure that you have proper y
connected the router to your computer.
If the device has not been configured previous y or the defau t settings have
been restored, after access to the web-based interface the Initia Configuration
Wizard opens (see the Initial Con iguration Wizard section, page 16).
12

DWR-980 Quick Installation Guide
If you configured the device previous y, after access to the web-based interface
the ogin page opens. Enter the username (admin) in the Userna e fie d
and the password you specified in the Password fie d, then c ick the LOGIN
button.
13

DWR-980 Quick Installation Guide
The Su ary page disp ays genera information on the router and its
software.
14

DWR-980 Quick Installation Guide
The Ho e page disp ays inks to the most frequent y used pages with device's
settings.
The web-based interface of the router is bi ingua (Eng ish/Russian). You can
se ect the needed anguage upon the initia configuration of the web-based
interface of the router or in the Syste / Configuration section of the
menu.
Other settings of the router are avai ab e in the menu in the eft part of the
page. Go to the re evant section and se ect the needed page or run the wizard
in the Initial Configuration section.
15

DWR-980 Quick Installation Guide
nitial Configuration Wizard
In order to start the Initia Configuration Wizard manua y, go to the Initial
Configuration section.
C ick the OK button and wait unti the factory defau t settings are restored.
If you perform initia configuration of the router via Wi-Fi connection, p ease
make sure that you are connected to the wire ess network of DWR-980 (see
the WLAN name (SSID) in the De ault Settings section, page 3) and c ick the
NEXT button. Then c ick the START button.
If the device has not been configured previous y or the defau t settings have
been restored, the Initia Configuration Wizard starts automatica y upon
access to the web-based interface or upon opening a web site on the Internet.
16

DWR-980 Quick Installation Guide
1. C ick YES in order to eave the current anguage of the web-based
interface or c ick NO to se ect the other anguage.
2. On the next page, c ick the CONTINUE button.
17

DWR-980 Quick Installation Guide
Selecting Operation Mode
In order to connect your device to a wired ISP, on the Device ode page,
from the Connection ethod ist, se ect the Ethernet (WAN) va ue. In
this mode you can configure a WAN connection, set your own settings for the
wire ess network in the 2.4GHz and 5GHz bands, configure LAN ports to
connect an STB or VoIP phone, and set your own password for access to the
web-based interface of the device.
18

DWR-980 Quick Installation Guide
In order to connect your device to a VDSL or ADSL ine, on the Device
ode page, from the Connection ethod ist, se ect the VDSL or ADSL
va ue corresponding y. In this mode you can configure a WAN connection, set
your own settings for the wire ess network in the 2.4GHz and 5GHz bands,
configure LAN ports to connect an STB or VoIP phone, and set your own
password for access to the web-based interface of the device.
In order to connect your device to the network of a 3G or LTE operator, on the
Device ode page, from the Connection ethod ist, se ect the 3G/LTE
ode va ue. In this mode you can configure an LTE WAN connection, set
your own settings for the wire ess network in the 2.4GHz and 5GHz bands,
and set your own password for access to the web-based interface of the device.
19

DWR-980 Quick Installation Guide
In order to connect your device to a wire ess ISP (WISP), on the Device
ode page, from the Connection ethod ist, se ect the Wi-Fi va ue. In
this mode you can connect your device to another access point, configure a
WAN connection, set your own settings for the wire ess network in the
2.4GHz and 5GHz bands, configure LAN ports to connect an STB or VoIP
phone, and set your own password for access to the web-based interface of the
device.
In order to connect your device to a private Ethernet ine, on the Device
ode page, from the Connection ethod ist, se ect the Ethernet (LAN)
va ue. In this mode you can configure one of the router's LAN port as the
WAN port, configure a WAN connection, set your own settings for the
wire ess network in the 2.4GHz and 5GHz bands, configure LAN ports to
connect an STB or VoIP phone, and set your own password for access to the
web-based interface of the device.
When the operation mode is se ected, c ick the NEXT button.
20