D-Link DAP-2590 - AirPremier N Dual Band PoE Access... User manual

2 DAP-2590 Install Guide
Minimum System Requirements:
• CD-ROM Drive
• Computers with Windows®, Macintosh®, or Linux-based operating
systems
• Installed Ethernet Adapter
• Internet Explorer version 7.0 or Firefox 3.0 and above
System Requirements
Package Contents
Note: Using a power supply with a different voltage than the one included with the
DAP-2590 will cause damage and void the warranty for this product.
If any of the above items are missing, please contact your reseller.
DAP-2590 802.11n
Access Point
Power Adapter
Ethernet CableCD-ROM
Mounting Plate

DAP-2590 Install Guide 3
Hardware Overview
LEDs
5 GHz - When lit, the access point is operating at 5GHz.
This light will blink when there is wireless trafc.
2.4 GHz - When lit, the access point is operating at 2.4GHz.
This light will blink when there is wireless trafc.
LAN - Solid light when the Ethernet port is connected to a
working port, such as a router or switch. The light will blink
when there is trafc through LAN port.
POWER - The light will blink during boot up. Once solid, the
access point is ready.

4 DAP-2590 Install Guide
Installing the Hardware
Power Receptor
LAN Port (PoE)
Reset
Antennas

DAP-2590 Install Guide 5
To power the access point, you can use one of the following methods:
1. Use the supplied power adapter
2. Connect one end of your Ethernet cable into the LAN (PoE) port on the
DAP-2590 and the other end into one port on a PoE switch.
To setup and manage the DAP-2590 from a computer, use one of the
following methods:
1. Connect a straight through Ethernet cable between the access point
and your computer.
2. Connect the access point to a switch or router and use a computer from
a computer that is also connected to that switch or router.
3. Please start your web browser program,
type the IP address of the device (http://
192.168.0.50) and press Enter. Make sure
that the IP addresses of the device and your
computer are in the same subnet. Then, refer
to the Manual for conguration.

6 DAP-2590 Install Guide
Step 1: Insert provided wall anchors in the wall where the mounting plate will
be attached.
Mounting Plate Assembly
Step 2: Use the provided screws to secure the mounting plate on the wall.

DAP-2590 Install Guide 7
Step 3: Attach the remaining screws securely to the back of the DAP-2590.
Step 4: Attach the DAP-2590 to the mounting plate.

8 DAP-2590 Install Guide
Step 5: Slide the DAP-2590 down into the grooves on the mounting plate to
secure it to the plate.

DAP-2590 Install Guide 9
When you have completed the steps in this Installation Guide and congured
your for your network, your network should look similar to this:
Your Setup is Complete
* Maximum Wireless signal rate derived from IEEE 802.11n (draft 2.0) specications. Actual data
throughput will vary. Network conditions and environmental factors, including volume of network
trafc, building materials and construction, and network overhead lower actual data throughput
rate.

10 DAP-2590 Install Guide
Notes

DAP-2590 Install Guide 11
Notes

Technical Support
D-Link’s website contains the latest user documentation and
software updates for D-Link products.
U.S. and Canadian customers can contact D-Link Technical
Support through our website or by phone.
United States
Telephone
[phone]
World Wide Web
http://support.dlink.com
Canada
Telephone
[phone]
World Wide Web
http://support.dlink.com
Version 1.1
August 18, 2008
6DAP2590Q.B2G
Copyright ©2008 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link, the D-Link logo, and AirPremier are
trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States and other countries. Other
trademarks are the property of their respective owners. All references to speed are for comparison purposes only. Product
specications, size, and shape are subject to change without notice, and actual product appearance may differ from that
depicted herein. Visit www.dlink.com for more details.