Da-Lite TENSIONED DUAL MASKING ELECTROL User manual

DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: [phone]
800-622-3737
Fax: [phone]
Toll Free Fax: [phone]
www.da-lite.com
e-mail: [email protected]
Instruction Book for
TENSIONED DUAL MASKING ELECTROL®
The Da-Lite Difference.

1
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rat-
ing at least equal to that of the appliance should be used.
Cords rated for less amperage than the appliance may over-
heat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of fire, electric shock, or
injury to persons.
SAVE THESE INSTRUCTIONS

2
PRE-INSTALLATION
1. Carefully unpack screen and remove outer wrapping from case.
2. Make sure to recheck measurements of screen location before installation.
3. Remove center support brackets (on 8' and wider screens only), reverse brackets and reinstall flush with the top of the
box.
INSTALLATION
1. Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting
bracket.
2. Level unit lengthwise with a carpenter’s level and plumb level. Secure opposite end.
CAUTION! Do not seal in until screen has been secured in position and properly tested for satisfactory operation.
3. Carefully remove three shipping brackets by removing six hex head screws from case and three phillips head
screws from aluminum slat. Use a phillips screwdriver, a hex socket and a ratchet. Slat should move freely (Fig. 1).
4. Detach access panel by removing screws (Fig. 1).
5. Remove junction box cover plate.
6. Install electric hook up that applies to your unit. Make sure to review your electrical installation checklist and wiring
diagram (included) for either 120 volt switch, 220/240 volt switch or low voltage control.
NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.
7. Carefully remove two wood boards securing mask surface to case.
8. Test installation by carefully running picture and mask surfaces up and down several times. Be prepared to stop
screen. Standard Duty Cycle: 1 MIN. ON / 3 MIN. OFF.
NOTE: When rolled down, the picture surface should wrap fully around the roller. No part of the roller should be exposed.
Picture and mask surfaces will automatically stop in the down position.
The mask will start down off the front of the roller, travel completely down past the bottom of the viewing surface,
then “step back” against the viewing surface to eliminate shadowing by rolling up the back side of the roller. Do not
adjust the limits to change this feature.
9. Run the picture and mask surfaces upward. When the picture and mask surfaces are fully up the limit switches (in
the motors) are tripped and the motors shut off.
10. Check for satisfactory condition by operating screen a few times. Reinstall access panel.
s
!
s
!
FIGURE 1 FIGURE 2
DRYWALL
SCREW
ACCESS PANEL
MACHINE SCREW
PHILLIPS HEAD SCREW
SHIPPING BRACKET
ADJUSTMENT
KNOB “UP”
PICTURE SURFACE
MASK SURFACE
ADJUSTMENT
KNOB “DOWN” MASK MOTOR
SCREEN MOTOR
HEX HEAD SCREW

3
SCREEN ADJUSTMENT FOR 120V SCREENS
CAUTION! THE MASK SHOULD NOT BE FIELD ADJUSTED FOR MORE OR LESS DROP.
Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly ad-
justed at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:
NOTE: Use a screw driver or allen wrench to make adjustments.
MORE SCREEN DROP
1. Remove access panel (Fig. 1).
2. Place operating switch in “down” position.
3. When the screen stops, turn the “down” limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising picture
surface approximately two feet, then lower again. Repeat until desired picture surface position is attained.
NOTE: Stop adjustment when string screws reach the bottom of roller and there is no wraps of string around the roller. Beyond
this point the roller will start pulling up the aluminum slat, the fabric will still be coming down and severe damage to the fab-
ric will occur!
4. Replace access panel.
LESS SCREEN DROP
1. Remove access panel. (Fig. 1).
2. Raise picture surface approximately two feet above desired level.
3. Place operating switch in “off” position.
4. Turn the “down” limit knob (Fig. 2) one-quarter turn clockwise. Test by raising picture surface approximately two
feet, then lower again. Repeat until desired picture surface position is attained.
5. Replace access panel.
s
!
DOWN
BLACK
UP
DOWN
COMMON WHITE
COMMON
GROUND GREENGROUND
MASK SCREEN
UP
DOWN
MASK MOTOR
4 – WIRE
MASK MOTOR
UP
OFF
DOWN
4 – WIRE
SCREEN MOTOR
SCREEN MOTOR
115V. A.C. 60 CYCLE
BLACK (HOT)
BLACK
RED
WHITE
WHITE (COMMON)
GREEN
GROUND WIRE
RED
UP
115V DUAL MOTOR
CONTROL
TENSIONED DUAL MASkINg ELECTROL® INSTRUCTIONS

4
UP BROWN
DOWN
COMMON
BLACK
BLUE
UP
GREEN
4 – WIRE
MASK MOTOR
GROUND
MASK MOTOR
MASK SCREEN
UP
UP
OFF
DOWN
DOWN
BROWN
DOWN
BLACK
COMMON BLUE
GROUND
GREEN
4 – WIRE
SCREEN MOTOR
SCREEN MOTOR
220V. A.C. 60 CYCLE
BROWN (HOT)
BLUE (COMMON)
GROUND WIRE
220V DUAL MOTOR
CONTROL
SCREEN ADJUSTMENT FOR 220/240V SCREENS
CAUTION! THE MASK SHOULD NOT BE FIELD ADJUSTED FOR MORE OR LESS DROP.
Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly ad-
justed at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:
NOTE: Use a screw driver or allen wrench to make adjustments.
MORE SCREEN DROP
1. Remove access panel (Fig. 1).
2. Place operating switch in “down” position.
3. When the screen stops, turn the “down” limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising picture
surface approximately two feet, then lower again. Repeat until desired picture surface position is attained.
NOTE: Stop adjustment when string screws reach the bottom of roller and there is no wraps of string around the roller. Beyond
this point the roller will start pulling up the aluminum slat, the fabric will still be coming down and severe damage to the fab-
ric will occur!
4. Replace access panel.
LESS SCREEN DROP
1. Remove access panel. (Fig. 1).
2. Raise picture surface approximately two feet above desired level.
3. Place operating switch in “off” position.
4. Turn the “down” limit knob (Fig. 2) one-quarter turn clockwise. Test by raising picture surface approximately two
feet, then lower again. Repeat until desired picture surface position is attained.
5. Replace access panel.
s
!
TENSIONED DUAL MASkINg ELECTROL® INSTRUCTIONS

5
SUggESTED METHODS OF INSTALLATION
Offset mounting, recessed above ceiling. For plaster, dry
wall, tile or paneling. Bottom of case painted same finish
as ceiling.
Offset mounting, recessed above ceiling. May be
adapted for 3/4" ceiling, but cut to 1/4" thick under
screen case and panel.
NOTE:
MUST MARK HOLE LOCATION OF SCREWS IN 3-1/2" PANEL FOR REMOVAL, IF COVERING WITH TILE.
Offset mounting, recessed above ceiling. May be
adapted for 1/4" paneling for ceiling.
Flush mounting, recessed above ceiling. For use with
dropped ceiling. May also be adapted for use with
acoustical or other ceiling 3/4" thick but cut to 1/4" thick
under screen case and panel.
METHOD A METHOD B
METHOD C METHOD D
(SUGGESTED)
1/4" LAG
SCREWS
1-1/2"
1-1/2"
MOUNTING
JOIST
3/4" FINISHED
CEILING 3-1/2"
PANEL
CAN BE PAINTED SAME AS CEILING
OR REMOVED AND REPLACED WITH
FINISHED CEILING
ALUMINUM SLAT
9-3/16"
9"
MOUNTING
BRACKET
8-11/16"
FURRING
STRIP
PICTURE SURFACE
MASKING SURFACE
3/16" X 1" STEEL BAR
IN POCKET
(SUGGESTED)
1/4" LAG
SCREWS
1-1/2"
1-1/2"
MOUNTING
JOIST
3/4" FINISHED
CEILING 3-1/2"
PANEL
CEILING TILE CUT TO 1/4" THICK
(ATTACH WITH MASTIC)
ALUMINUM SLAT
9-3/16"
9" MOUNTING
BRACKET
8-15/16"
FURRING
STRIP
PICTURE SURFACE
MASKING SURFACE
3/16" X 1" STEEL BAR
IN POCKET
(SUGGESTED)
1/4" LAG
SCREWS
1-1/2"
1-1/2"
MOUNTING
JOIST
FINISHED
CEILING 3-1/2"
PANEL
ALUMINUM SLAT
9-3/16"
9" MOUNTING
BRACKET
8-15/16"
FURRING
STRIP
PICTURE SURFACE
MASKING SURFACE
3/16" X 1" STEEL BAR
IN POCKET
1-1/2"
MOUNTING
JOIST
SUSPENDED
CEILING
TILE
3/16" X 1" STEEL BAR
IN POCKET
MASKING SURFACE
PICTURE SURFACE
FURRING
STRIP
8-15/16"
1-1/2"
(SUGGESTED)
1/4" BOLTS
3-1/2"
PANEL
T-BAR FURNISHED
WITH CEILING
ALUMINUM SLAT
TENSIONED DUAL MASkINg ELECTROL® INSTRUCTIONS
CASE LENGTH = SCREEN FABRIC WIDTH
+ 15-3/4", ALL SIZES
1-1/2"
MOUNTING BRACKET
MOTOR END
9"
ELECTRICAL OUTLET
7-7/8"
7-7/8"
8-11/16"
8' AND WIDER SCREENS ONLY

6
Printed in U.S.A. 77607 Rev. 3/95
TROUBLESHOOTINg
SYMPTOM
1. Screen will not operate.
Motor does not hum.
2. Incorrect stopping position in
downward direction.
3. Incorrect stopping position in
upward direction.
4. Noise.
NOTE: Screen will operate with a
low pitched hum.
5. Coasting.
CAUSE
(a) Incorrect line voltage.
(b) Blown fuse.
(c) Tripped circuit breaker.
(d) No power to operating switch
or junction.
Power at junction box
(e) Thermal overload tripped.
(f) Broken wire in the “down” or “up”
position.
(g) Defective motor, limit switch or
capacitor.
(h) Capacitor burned out.
(a) “Down” limit switch out of
adjustment
(a) “Up” limit switch out of
adjustment
(a) Gear Noise.
(a) Defective brake.
SOLUTION
(a) Verify 115-125V (or 220-240V). If
insufficient voltage, rewire incom-
ing electric line.
(b) Replace fuse.
(c) Reset circuit breaker.
(d) Check above. Tighten all loose
wire connections. Correct any
improper connections.
“Down” Position
Check for power across black
and white leads.
“Up” Position
Check for power across red
and white leads.
(e) Let motor cool down for 15
minutes. Try again.
(f) Check for continuity. Cut off old
splice and reconnect.
(g) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(h) Replace motor assembly.
(a) See installation instructions.
(a) Adjust “up” limit switch. See
installation instructions
(a) Replace motor assembly.
(a) Replace motor assembly.

7Printed in U.S.A. 79338 Rev. 03/10
LIMITED ONE YEAR WARRANTY
ON DA-LITE PRESENTATION PRODUCTS
Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from
defects in materials and workmanship for a period of one (1) year from the date of purchase by
the original purchaser provided they are properly operated according to Da-Lite’s instructions and
are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental
damage, or which has been tampered with or repaired by a person other than authorized Da-Lite
personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)
the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer.
If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses
to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in
shipment. To protect yourself against damage or loss in transit, insure the product and prepay all
transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any implied
warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law
are limited to the one (1) year warranty period. This warranty gives you specific legal rights, and
you may also have other rights, which vary from state-to-state. NO LIABILITY IS ASSUMED
FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF
EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY
NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may
contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, [phone], [phone].
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN
ACCORDANCE WITH DA-LITE’S WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.