Daikin BRC1D52 User manual

Remote controller
BRC1D527
INSTALLATION MANUAL

1
1
1
4
4
1
2
2
1 2
3
3
S
M
S
S
MPCB
1
2
5
5
6
6
P2 P1 P2 P1
1 1
6
2
3
4 5
7
7
SETTING
UNIT No.
GROUP
c
a
3
1
d
e
4
562
7
b
8
8
1+22
22

BRC1D527
Remote controller
4PW16769-1
Installation manual
1
The kit includes the following parts:
1. Remove the upper part of remote
controller (Refer to figure 1)
Insert a minus screwdriver into the slots (1) in the
lower part of the remote controller (2 places), and
remove the upper part of the remote controller.
2. Fasten the remote controller (Refer
to figure 2)
For the field supplied switch box, use optional accessory
KJB111A or KJB211A.
BRC1D527 Remote controller Installation manual
READ THIS MANUAL ATTENTIVELY
BEFORE STARTING UP THE UNIT. DO
NOT THROW IT AWAY. KEEP IT IN YOUR
FILES FOR FUTURE REFERENCE.
IMPROPER INSTALLATION OR
ATTACHMENT OF EQUIPMENT OR
ACCESSORIES COULD RESULT IN
ELECTRIC SHOCK, SHORT-CIRCUIT,
LEAKS, FIRE OR OTHER DAMAGE TO
THE EQUIPMENT. BE SURE ONLY TO
USE ACCESSORIES MADE BY DAIKIN
WHICH ARE SPECIFICALLY DESIGNED
FOR THE USE WITH THE EQUIPMENT
AND HAVE THEM INSTALLED BY A
PROFESSIONAL.
IF UNSURE OF INSTALLATION PROCE-
DURES OR USE, ALWAYS CONTACT
YOUR DEALER FOR ADVICE AND
INFORMATION.
Remote controller Wood screws
Wall plugs Machine screws
The PC board is mounted in the upper part
of the remote controller. Be careful not to
damage the board with the minus
screwdriver.
1for exposed mounting, fasten with the two
included wood screws (Ø4x30) and plugs.
2for flush-mounting, fasten with the two
included machine screws (M4x16).
NOTE Choose the flattest place possible for the
mounting surface. Be careful not to
distort the shape of the lower part of the
remote controller by overtightening the
mounting screws.

Installation manual
2BRC1D527
Remote controller
4PW16769-1
3. Wire the indoor unit (Refer to figure 6)
Connect the terminals on top of the upper part of the
remote controller (P1, P2), and the terminals of the
indoor unit (P1, P2). (P1 and P2 do not have polarity.)
Wiring specifications
4. Reattach the upper part of the
remote controller
Refer to figure 4:
First begin fitting from the clips at the bottom.
If controlling one indoor unit or one
group of indoor units with two remote
controllers
Change the MAIN/SUB changeover switch setting as
described below (Refer to figure 3).
Set one remote controller to “main”, and the other to
“sub”.
1indoor unit
2lower part of the remote controller
3upper part of the remote controller
4wired from the rear
5wired from the top
6notch the part for the wiring to pass through
with nippers, etc.
NOTE When wiring, run the wiring away from
the power supply wiring in order to avoid
receiving electric noise (external noise).
Wiring type Size
2 wire 0.75–1.25 mm2
NOTE Peel the shield for the part that has to
pass through the inside of the remote
controller case (
l ). Refer to figure 5.
Be careful not to pinch the wiring when
attaching.
NOTE 1. The switch box and wiring for
connection are not included.
2. Do not directly touch the PC board
with your hand.
1Main remote controller (factory set)
2Sub remote controller
NOTE 1. If controlling with one remote controller,
be sure to set it to “main”.
2. Set the remote controller before turning
the power supply on.
“88” is displayed for about one minute when the
power supply is turned on. During this time the
remote controller can not be operated.

BRC1D527
Remote controller
4PW16769-1
Installation manual
3
5. Permission level function
■If required, you can limit the user action by
restricting the number of operable buttons. Refer
to the chapter "Field settings".
■For switching between level 1 permission and the
selected level in service, proceed as follows:
1Keep the fan speed button pressed,
2and press the 3 other indicated keys
simultaneously while keeping the fan speed
button pressed.
Refer to figure 8.
■If you want to limit the user action on the remote
controller to be defined as “sub”, start with only
connecting this controller to the unit. Make sure
that this controller is set to “main” (factory set)
first, change the permission level to the setting
you prefer and only then set the remote controller
to “sub”.
You can now proceed with connecting the remote
controller to be defined as “main”.
6. Field settings
If optional accessories are mounted on the indoor
unit, the indoor unit setting may have to be changed.
Refer to the instruction manual for each optional
accessory.
Refer to figure 7.
Procedure (Refer to figure 7)
1When in the normal mode, press the “ “
button for a minimum of four seconds, and the
FIELD SET MODE is entered.
2Select the desired MODE NO. with the “ ”
button.
3During group control, when setting by each
indoor unit (mode No. 20, 21, 22 and 23 have
been selected), push the “ ” button and
select the INDOOR UNIT NO. to be set. (This
operation is unnecessary when setting by
group.)
4Push the “ ” upper button and select
FIRST CODE NO.
5Push the “ ” lower button and select the
SECOND CODE NO.
6Push the “ ” button once and the present
settings are SET.
7
Push the “ ” button to return to the NORMAL
MODE.
Level Operable buttons
1All
2• on/off button
• schedule timer button
• temperature adjust button
• operation change/ button
•fan speed button
• air flow direction adjust button
3• on/off button
• temperature adjust button
•fan speed button
aUnit NO
bFirst Code NO
cSecond Code NO
dMode NO
eField set mode

Installation manual
4BRC1D527
Remote controller
4PW16769-1
Example
If during group setting and the time to clean the air
filter is set to FILTER CONTAMINATION - HEAVY,
SET MODE NO. to “10”, FIRST CODE NO. to “0”, and
SECOND CODE NO. to “02”.
Notes
NOTE 1. Setting is carried out in the group
mode, however, if the mode number
inside the parentheses is selected,
indoor units can also be set
individually.
2. The SECOND CODE number is set to
“01” when shipped from the factory.
3. Do not make any settings not given in
the table.
4. Not displayed if the indoor unit is not
equipped with that function.
5. When returning to the normal mode,
“88” may be displayed in the LCD in
order for the remote controller to
initialize itself.
6. It is not possible to change field
settings on the remote controller that
is set to “sub”.

BRC1D527
Remote controller
4PW16769-1
Installation manual
5
Mode
No.
Note 1
FIRST
CODE
NO. Description of setting
SECOND CODE NO. Note 2
01 02 03 04
10(20)
0
Filter Contamination - Heavy/Light
(Setting for spacing time of display time
to clean air filter)
(Setting for when filter contamination is
heavy, and spacing time of display time to
clean air filter is to be halved)
Ultra long
life filter
Approx.
10.000
hrs.
Approx.
5.000
hrs.
——
Long life
filter
Approx.
2.500
hrs.
Approx.
1.250
hrs.
Standard
filter
Approx.
200 hrs.
Approx.
100 hrs.
1
Long-life filter type (setting of filter sign indication
time). (Change setting when ultra-long filter is
installed)
Long-life
filter
Ultra-longlife
filter ——
2
Thermostat sensor in remote controller Use Not use — —
3
Spacing time of display time to clean air filter count
(setting for when the filter sign is not to be displayed)
Display Do not
display ——
11(21) 0
Setting number of connected Sky Air simultaneous
operation system indoor units (setting for
simultaneous operations system)
Pair Twin Triple Double twin
12(22)
1
ON/OFF input from outside (setting for when forced
ON/OFF is to be operated from outside).
Forced OFF ON/OFF
operation ——
2
Thermostat differential changeover (setting for when
using remote sensor).
1°C 0.5°C — —
13(23)
0
High air outlet velocity (for high ceiling applications). ≤2.7 m >2.7≤3.0 m >3.0≤3.5 m —
1
Selection of air flow direction (setting for when a
blocking pad kit has been installed).
4-way flow 3-way flow 2-way flow —
3
Selection of air flow function (setting for when using
a decoration panel for outlet).
Equipped Not
equipped ——
4
Air flow direction range setting. Upper Normal Lower —
6
Setting the external static pressure (setting
according to the connected duct resistance)
(for FHYK, follow the high ceiling setting)
Normal
(Normal)
High static
pressure
(High ceiling)
Low static
pressure
—
—
15(25) 3
Drain pump operation with humidifying. Equipped Not
equipped ——
Light
Heavy

Installation manual
6BRC1D527
Remote controller
4PW16769-1
Notes
1b
0
Permission level setting Level 2 Level 3 — —
1
Leave home function Not permitted Permitted — —
2
Thermostat sensor in remote controller (for limit
operation and leave home function only)
Use Not use — —
Mode
No.
Note 1
FIRST
CODE
NO. Description of setting
SECOND CODE NO. Note 2
01 02 03 04

NOTES

Zandvoordestraat 300, B-8400 Oostende, Belgium 4PWEN16769-1