Daintree GE Current UltraMax GED80MCC/Z2P1500 User manual

Installation Guide
XXXXXX | A-XXXXX
UltraMax®
Connected LED Driver (GE80MCC/Z2P1500)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation, or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes
• Use only UL-approved wire for input/output connections.
• Minimum size 14 AWG for continuous runs.
Prepare Electrical Wiring
Electrical Requirements
• The LED driver must be connected to the mains
supply according to its ratings on the product label.
• Class 1 wiring should be in accordance with NEC.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance to local electric code
of the country where the luminaire is installed.
RISQUES DE DÉCHARGES ÉLECTRIQUES
Coupe l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
Assurez-vous de correctement mettre à la terre le boitier d’alimentation
électrique
RISQUES D’INCENDIE
Respectez tous les codes NEC et codes locaux.
N’utilisez que des ls approuv é s par UL pour les entrees / sorties de
connexion. Taille minimum 14 AWG.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-005(A)/NMB-005(A)
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

UltraMax® Connected LED Driver (GED80MCC/Z2P1500) Installation Guide
2
1. Remove power from LED luminaire by switching circuit breaker powering the LED luminaire to the o position.
CAUTION: Turning o the LED luminaire’s wall switch may not remove voltage from the LED luminaire.
2. For maximum safety, LED luminaire must be grounded. Make sure LED luminaire is properly grounded with a green
ground wire per National Electrical Code (NEC).
3. Verify that the LED driver is the correct LED driver for the LED luminaire, input voltage, and application.
4. Follow all relevant National Electric Code (NEC), Federal, State and Local Electric Codes as well as U.L. safety standards.
5. Access and open driver compartment cover.
6. Remove old driver and any extra wires from enclosure.
7. Inspect and replace any damaged or deteriorated cable.
8. Review the wiring diagram on the new driver label and identify connections to be made.
9. Install the new LED driver and make sure the new LED driver is properly grounded to metal of LED luminaire per
National Electrical Code (NEC). Tighten driver mounting screws seating driver rmly against the LED luminaire
surface. To ensure electrical grounding between driver case and LED luminaire housing, mounting screws with star
washers are recommended to break (penetrate) the painted surface of the driver mounting foot.
10. Install the antenna within the LED luminaire enclosure (away from grounded metal surfaces when possible). The
antenna shall not be cut or have any insulation material removed or tampered with in any way.
11. Use only U.L. approved wire connectors for all electrical connections.
CAUTION: Wire connectors must be securely fastened and must completely cover exposed wire ends to prevent
shock hazard.
12. Be sure to insulate unused leads INDIVIDUALLY to 600Vrms using U.L. approved wire connectors.
13. Verify that all installation and safety requirements have been completed and reinstall driver cover.
14. Restore power at circuit breaker, apply power to the xture and ensure LED luminaire is operational.
Before installing this driver:
During installation:
After driver installation:

www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
INDXXX (Rev XX/XX/XX) Enovia - A-XXXXX
Product Title (XXX- Series) Installation Guide
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment (GED80MCC/Z2P1500) contains the limited module with FCC ID 2AS3F-80MCCZ2P15 and ISED ID
25008-80MCCZ2P15. This equipment complies with FCC CFR 47 Part 2 requirements for radiation exposure for xed facility
or mobile applications that maintain a distance of 20 cm from a person’s body. This equipment complies with ISED RSS-
102 Issue 5 requirements for radiation exposure limits for an uncontrolled environment that maintain a distance of 20 cm
from a person’s body.
This radio transmitter ISED ID 25008-80MCCZ2P15 has been approved by Innovation, Science and Economic Development
Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for
use with this device.
Any changes or modications to the equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Only the following antennas should be used with this limited module and the antenna should only be installed when the
host product is manufactured. (The antenna is not eld replaceable.)
PulseLARSEN W3357 (50Ω impedance; peak gain over 2400 – 2483.5 MHz range is 0.4dBi)
Walsin RFPCA430618IMAB301 (50Ω impedance; peak gain over 2400 – 2483.5 MHz range is 2.2dBi)
Suppliers Name: Current Lighting Solutions, LLC
www.gecurrent.com