Dancover 5.4m Series User manual

14-12-2017
for
Garage Tent
5.4m Series
Manual

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is
your responsibility to comply with local rules and regulations and to ensure that the
marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is
safely secured and that the marquee/tent does not cause damage to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent
with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents
insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent regularly to
prevent snow from building on the roof as heavy snow can cause the marquee/tent to
collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility
to ensure rain puddles do not build up. As a precaution, make sure the roof of the
marquee/tent is stretched out properly and adequately over the side frames of the
marquee/tent and remove rain water regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of
temperatures below zero always unpack and repack your marquee/tent indoors to avoid
the risk of cracking parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manuall.
This structure is not tested for snow and wind loads. We always recommend that you
remove snow from the roof.

PARTLIST FOR 5.4m series
Part no. Description 6m 7,5m 9m 10,5m
1 Leg 10 12 14 16
2 Female brace 60’’ 7 7 7 7
3 Corner arch 10 12 14 16
4 Center arch 5 6 7 8
5 Male door rail 5 6 7 8
6 Female door rail 5 6 7 8
7 T-bar 5 6 7 8
8 Male brace 63’’ 21 28 35 42
9 Diagonal 80’’ 4 4 4 6
10 Rope 4 4 4 4
11 S-hook 16 16 16 16
12 Big door rail hook 24 24 24 24
13 Elastic bungee 16 16 16 16
14 Floor bracket 8 8 8 8
15 Nail 16 16 16 16
16 Carriage bolt 1 ¾’’ 6 7 8 9
17 Carriage bolt 2 ½’’ 11 13 15 17
18 Carriage bolt 4’’ 27 33 38 43
14-12-2017

PARTLIST FOR 5.4m series
Part no. Description 6m 7,5m 9m 10,5m
19 Wing nut 55 66 77 88
20 Big plastic cap for
legs
10 12 14 16
21 Small plastic cap for
cross pipe
14 14 14 14
22 Roof 1 1 1 1
23/24 Set with door right
and door left
2 2 2 2
14-12-2017

4
1
65
1
7
33
use Bolt
part 16
DEAR CUSTOMER
Please use gloves when assembling the metal frame portion of this unit. The metal components of
this product have been treated with a rust preventive coating that may feel oily to the touch. This
coating is not dangerous, but may dirty your hands during assembly. We recommend that you
wipe metal parts clean with a mixture of warm water and dish detergent prior to assembly. Should
your hands become dirty, simply wash with soap and water.
ASSEMBLY INSTRUCTIONS
1. Take a Center Arch (no. 4) and on each end of it, assemble a Corner Arch (no. 3). Secure the Male
and Female Door (no. 5) and (no. 6) to the Arch (no. 3).
2. Slide the Rail Hooks over the Door Rails before tightening. Add the T-Bar (no. 7) to the Door Rails
and the Center Arch.

3. On each end of (no. 3), install the Leg (no. 1). Repeat step 1 for all frames.
4. At this point stand up the front or back frame and add 7 male connecting pipes (no. 8). Then stand up
another frame and add 7 female connecting pipes (no. 2). For the remaining frames use the male
connecting pipes (no. 8).
5. Add the diagonals (no. 9) to the rst and last legs (no. 1).
Note: Make sure all screws are tight. Do not over-tighten.
6. ROOF ASSEMBLY
Take the roof and place it over the structure. Make sure
that the windows are on the two sides of the shelter, at
front or at back as your choice.
Tie all the ropes around the pipes.
7. SHELTER REINFORCEMENT
Before you install the oor brackets, make sure the
distance between the legs is 18 feet wide.
Place the oor brackets (14) at each end of the shelter.
Then drive in nails (15) into ground, gravel or asphalt.
Other material surfaces require other types of anchoring
(cement blocks, sand bags, screw and bolt, etc). Permanent
anchors are not provided with this unit.
8. DOOR INSTALLATION
Install doors at each end. Connect door with roof by velcro
as shown. Use elastics (13) to attach the door to the roof
with hooks (11). Close the end of hook on the elastic so it
won’t fall on out. Use the rail hooks to attach door the door
rails. When closing at the front, make sure all elastics are
attached on the inside and outside of the shelters.