Dantel 46022-12 User manual

CAUTION
•Install or remove modules from the shelf only when the power is off.
If you install a module in the shelf with the power on, the internal
circuitry may suffer damage and the product warranty will be void.
•Remove and install circuit boards only in a static-safe environment
(use antistatic wrist straps, smocks, footwear, etc.).
•Keep circuit boards in their antistatic bags when they are not in use.
•Do not ship or store circuit boards near strong electrostatic, electromag-
netic, magnetic, or radioactive fields.
•For more complete information on electrostatic discharge safety
precautions, refer to BellcoreTM Technical Reference # TR-NWT-000870.
Copyright 1999 by Dantel, Inc. • Dantel is a registered trademark of Dantel, Inc. • ISO 9001 Registered
Printed in the U.S.A.
INSTALLATION & OPERATION MANUAL
46022-12-0299<90-00008>
46022-12
MULTIPLE ALARM
COMBINER
About this Practice:
The practice has been reissued to:
• Update Fig. 5.
Issue date: February 1999
Reissued Practices: Updated and
new content can be identified by a
banner in the right margin.
UPDATED
Table of Contents
Ordering Information ........................................................................... 2
General Description.............................................................................. 2
Circuit Description ............................................................................... 2
Installation............................................................................................ 4
Operation .............................................................................................. 7
Application Information ....................................................................... 7
Technical Specifications ..................................................................... 10
Warranty ............................................................................................. 12
46022-12
Multi-Alarm
Combiner
RX DATA
12
34
56
78
910
11 12
AB
CD
14
13
15 16
46022-12 REV__

PAGE 2 46022-12-0299 <90-00008>
ORDERING INFORMATION
NOTE: This section lists the different options available for this product. To order any of the avail-
able options, contact Dantel Inside Sales through our toll-free number, 1-800-432-6835.
OPTION NUMBER FEATURES
A11-46022-12 Multiple Alarm Combiner
GENERAL DESCRIPTION
The 46022-12 Multiple Alarm Combiner (MAC) uses RS-422 communications to interface the data port of the 46020
Multiple Alarm Processor (MAP) to remote components of
Dantel’s 460 Alarm and Control System (ACS). It has eight
ports and also provides an alarm status display. The front panel
has LEDs and switches for alarm status indication, alarm
acknowledgment, and control point operation.
The MAC is a plug-in printed circuit module that fits into any
Dantel 400-type or similar equipment housing. It operates on
-21 to -56 VDC input power.
CIRCUIT DESCRIPTION
Fig. 1 shows an illustration of the 46022-12 MAC functional schematic. The circuit consists of an address logic selector,
display latches and drivers, and a regulated power supply.
Address Logic Selector
The address logic selector makes an address exclusive to the
module. To assign an address (1-8), set the mini-DIP switches
labeled S1-1, 2, 3, and 4. The 46020 MAP in the Alarm and
Control System uses this address to sequence alarm polling data
to each MAC in the alarm system.
Display Latches and Drivers
The display drivers supply operating current to the LEDs.
Whenever a display signal is received at the MAC, the display is
latched ON. The LEDs remain latched ON until:
♦The alarm’s status returns to normal,
♦The alarm system master (controlling computer terminal)
acknowledges the alarm condition and status changes,
- or -
♦You operate the front panel acknowledgment switches.
The specific operation of the front panel switches and LEDs is
dependent on the firmware version. Check the appropriate
firmware manual for more information.

46022-12-0299<90-00008> PAGE 3
Regulated Power Supply
The regulated power supply uses -21 to -56 VDC input power to
supply ±12 VDC and +5 VDC to the module’s circuit board.
It also supplies the following to the edge connector for off-board
use:
♦+12 VDC (pin 47)
♦-12 VDC (pin 49)
♦+5 VDC (pin 45)
FIG. 1 - FUNCTIONAL SCHEMATIC, 46022-12 MULTIPLE ALARM COMBINER
POWER
SUPPLY
RS422
Interface
RS422
RS422
RS422
RS422
RS422
RS422
RS422
GND
GROUND
-21 TO -56 VDC
SERIAL PORT 1
PORT 2
PORT 3
PORT 4
PORT 5
PORT 7
PORT 8
PORT 6
DATA ENABLE 52
CHANNEL ADDRESS 0 46
CHANNEL ADDRESS 1 42
CHANNEL ADDRESS 2 43
CHANNEL ADDRESS 3 44
CARD ADDRESS 0 54
CARD ADDRESS 1 51
CARD ADDRESS 2 53
DATA 55
ST 50
ALM 36
DISPLAY REQUEST 56
TXD 48
RXD 41
(RTS) 39
+5 VDC 45
+12 VDC 47
- 12 VDC 49
MULTIPLE
ALARM
COMBINER
ADDRESS
LOGIC
SELECTOR
PUSH
BUTTON
SWITCHES
RX
DATA
+5 VDC
DISPLAY
LEDS
17
35
1
2
19
20
3
4
21
22
5
6
23
24
7
8
25
26
9
10
27
28
13
14
31
32
15
16
33
34
11
12
29
30
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
RX +
RX -
TX +
TX -
AB
AB
AB
AB
AB
AB
AB
AB
CIRCUIT DESCRIPTION

PAGE 4 46022-12-0299 <90-00008>
INSTALLATION
Installation consists of setting the straps and switches, wiring the connector, and installing the module.
Each of the eight ports of the 46022-12 MAC has an RS-422
data communications interface. If you require a different
interface, connect the serial alarm device through a 46035
Converter Module or a 46022-20 MAC equipped with the appro-
priate interface subassembly.
1. Set the straps.
You can strap the 46022-12 MAC to have its alarm inputs
(receive lines) either terminated or unterminated. The termi-
nating load is 100 ohms. Each alarm port must have a current
path at some point of termination, which is normally set at the
MAC.
♦If a channel is connected to communications lines, the resis-
tor is normally strapped IN (position B).
♦If termination for a channel is provided at the source, strap
the resistor OUT.
Refer to Table A and Fig. 2.
2. Set the switches.
A mini-DIP switch (S1) selects the card address, used by the
46020 MAP to sequence all MACs in an alarm system. Refer to
Table B and Fig. 2 to set the switches.
NOTE: In order for the system to function properly, two MACs cannot
share the same address.
To make any port of the 46022-12 MAC addressable for
interfacing remote discrete alarm points to the shelf without
rewiring, you may use the 46022-12 MAC in conjunction with a
46022-30 MAC.
3. Wire the connector.
Normally the 56-pin edge connector in the shelf is prewired at
the factory. If you are going to wire the connector, refer to Fig. 3
for module connector pin wiring assignments. Wire the connec-
tor in the shelf or housing as required.
4. Install the module in the equipment housing.

46022-12-0299<90-00008> PAGE 5
TABLE A - STRAP OPTION DESIGNATIONS TABLE B - 46022-12 ADDRESS SWITCH SETTINGS
FIG. 2 - STRAP AND SWITCH LOCATIONS, 46022-12 MAC
INSTALLATION
1234
ON OFF
RCV LINE
TERMINATION
A B
8
7
6
5
4
3
2
1
SERIAL
PORTS
S1
rebmuNtroPmralA noitisoP
detanimretnU1
*detanimreT1
A1
B1
detanimretnU2
*detanimreT2
A2
B2
detanimretnU3
*detanimreT3
A3
B3
detanimretnU4
*detanimreT4
A4
B4
detanimretnU5
*detanimreT5
A5
B5
detanimretnU6
*detanimreT6
A6
B6
detanimretnU7
*detanimreT7
A7
B7
detanimretnU8
*detanimreT8
A8
B8
gnitteStluafeDyrotcaF*
sserddA rebmuN gnitteShctiwS
1-1S 2-1S 3-1S 4-1S
*1 NO FFO FFO FFO
2 NO NO FFO FFO
3 NO FFO NO FFO
4 NO NO NO FFO
5 NO FFO FFO NO
6 NO NO FFO NO
7 NO FFO NO NO
8 NO NO NO NO
gnisusnoitacilpparofgnittestluafeD*
.CAMenoylno

PAGE 6 46022-12-0299 <90-00008>
FIG. 3 - PIN DESIGNATIONS, 46022-12 MAC
56 55
54 53
52 51
50 49
48 47
46 45
44 43
42 41
40 39
38 37
36 35
34 33
32 31
30 29
28 27
26 25
24 23
22 21
20 19
18 17
16 15
14 13
12 11
10 9
87
65
43
21
CIRCUIT SIDE OF PCCOMPONENT SIDE OF PC
" 3
-12 VDC (OUTPUT)
+12 VDC (OUTPUT)
+5 VDC (OUTPUT)
MAP CHANNEL ADDRESS 2
TXD MODEM DATA CONNECTION
-21 TO -56 VDC
RECEIVE -
ALM
MAP CHANNEL ADDRESS 1
DATA
DISPLAY REQUEST
CARD ADDRESS 0
ENABLE
WRT
CARD ADDRESS 2
CARD ADDRESS 1
SERIAL OUTPUT DATA
MAP CHANNEL ADDRESS 0
MAP CHANNEL ADDRESS 3
PORT 8
" 7
" 6
" 5
" 4
" 3
" 2
PORT 1
PORT 8
" 7
" 6
" 5
" 4
" 2
PORT 1
RECEIVE +
TRANSMIT - TRANSMIT +
GROUND
PORT 8
" 7
" 6
" 5
" 4
" 3
" 2
PORT 1
PORT 8
" 7
" 6
" 5
" 4
" 3
" 2
PORT 1
INSTALLATION

46022-12-0299<90-00008> PAGE 7
OPERATION
The 46022-12 Multiple Alarm Combiner has the following indicators on the front panel:
♦Sixteen red LEDs indicate alarm site and individual alarm
point status. A momentary contact switch next to each LED
is for alarm acknowledgment and other functions.
♦Four green LEDs indicate the individual alarm level (A, B, C,
or D).
♦One green LED labeled RX DATA indicates that the unit is
receiving data.
The way the unit operates is dependent on the 46020 MAP
firmware. Refer to the appropriate firmware manual for com-
plete operating information.
APPLICATION INFORMATION
Fig. 4 shows a 46022-1x MAC downline from the 46020 Multiple Alarm Processor (MAP) data port. The first alarm
port on the MAC sends discrete point alarm data to and from a
46030 Control Point Module (CPM) and its associated 46010
Multiple Alarm Transmitters (MATs). The other seven MAC
alarm ports go directly to TBOS serial ports.
Fig. 5 shows two MACs connected in parallel to a MAP. This
MAP connects in parallel with a second MAP and its hardware.
The two MAPs connect to a 46033 E-System Adapter Module
and then to an E-System master. All remote alarm soucres in
this example are TBOS serial ports.
46022-12
Multi-Alarm
Combiner
RX DATA
12
34
56
78
910
11 12
AB
CD
14
13
15 16
46022-12 REV__

PAGE 8 46022-12-0299 <90-00008>
FIG. 4 - EXAMPLE APPLICATION, SINGLE MAC
1
2
3
4
5
6
7
8
TBOS
SERIAL
PORTS
RS422
PORTS
46009
RS232
INTERFACE
46033-XX
E-SYSTEM
ADAPTER
49012
or
49013
202
MODEM
46020-XX
MAP
TO
NMA
MASTER
or
TASC
TCAS
16 ALM. PTS.
16 ALM. PTS.
16 ALM. PTS.
16 CONTROL
POINTS
(NOTE 2)
46028-XX
46029-XX
CPM
49008
RS422
INTERFACE
46010-XX
MAT
46010-XX
MAT
46010-XX
MAT 46022-1X
MAC
NOTES
1. Example remote shown serves 7 serial ports, 48 discrete alarm points and 16 discrete control points.This requires 7 slots in
a 400- type shelf, leaving 5-7 slots for fuse module, and line amplifier.
APPLICATION INFORMATION

46022-12-0299<90-00008> PAGE 9
FIG. 5 - EXAMPLE APPLICATION, TWO MACS
46020-XX
MAP
No. 1
46033-XX
E-SYSTEM
ADAPTER
49012
or
49013
202
MODEM
46020-XX
MAP
No. 2
TO
MAC'S
RS422
SERIAL
ALARM
PORTS
RS422
SERIAL
ALARM
PORTS
TONES
TO
E-SYSTEM
49029
RS232
INTERFACE
49029
RS232
INTERFACE
CHANNEL ADDRESS 0
CHAN ADR 1
CHAN ADR 2
CHAN ADR 3
CARD ADR 0
CARD ADR 1
CARD ADR 2
DATA
WRT
ALM
DIS. REQ.
EN
RXD
TXD
46
42
43
44
54
51
53
55
50
36
52
48
41
56
20
21
PARALLEL WIRING
TO UP TO 2
ADDITIONAL MAP's
(if used)
20
21
20
22
19
21
XMT
RCV
13
9
11
46022-1X
MAC
No. 1
1
2
19
20
3
4
21
22
5
6
23
24
7
8
25
26
9
10
27
28
12
29
30
31
32
15
16
33
34
13
14
11
1
2
19
20
3
4
21
22
5
6
23
24
7
8
25
26
9
10
27
28
12
29
30
31
32
15
16
33
34
13
14
39
46
45
43
44
54
51
53
55
50
49
52
1
5
56
7
46
42
43
44
54
51
53
55
50
36
52
48
41
56
39
PORT 11
PORT 12
PORT 13
PORT 14
PORT 15
PORT 16
PORT 10
PORT9
PORT 1
PORT 2
PORT 3
PORT 4
PORT 5
PORT 6
PORT 7
PORT 8
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
RX+
TX+
RX-
TX-
46022-1X
MAC
No. 2
46020
MAP
No. 1
46020
MAP
No. 2
46033
E-System
Adapter
APPLICATION INFORMATION
UPDATED

PAGE 10 46022-12-0299<90-00008>
TECHNICAL SPECIFICATIONS
noitpircseD eulaV
egatloVtupnI CDV65-ot12-
tnerruCtupnI CDV12-@
Am021
CDV42-@
Am011
CDV84-@
Am08
CDV65-@
Am07
noitapissiDtaeH CDV12-@
rH/utB6.8
CDV42-@
rH/utB0.9
CDV84-@
rH/utB1.31
CDV65-@
rH/utB4.31
egatloVtuptuO
)mumixam(tnerruCtuptuO
CDV5+
xaMAm002
CDV21+
xaMAm02
CDV21-
xaMAm02
thgieW secnuo57.8
snoisnemiDlacisyhP "6.5x"0.6x"4.1
egnaRerutarepmeTgnitarepO Cseerged55ot0
.daolegatlovtuptuohtiwyravyamnoitapissidtaehdnatnerructupnI:ETON

46022-12-0299<90-00008> PAGE 11
NOTES

PAGE 12
12 PAGES 46022-12-0299 <90-00008>
LIMITED WARRANTY
The Seller warrants that the standard hardware products sold will be free from defects in material and work-
manship and perform to the Seller’s applicable published specifications for a period of 18 months for hardware,
and 3 months for software, from the date of the original invoice. The liability of the Seller hereunder shall be
limited to replacing or repairing, at its option, any defective products which are returned F.O.B. to the Seller’s
plant, (or, at the Seller’s option, refunding the purchase price of such products). In no case are products to be
returned without first obtaining permission and a customer return authorization number from the Seller. In
no event shall the Seller be liable for any consequential or incidental damages.
Equipment or parts which have been subject to abuse, misuse, accident, alteration, neglect, unauthorized
repair or installation are not covered by warranty. The Seller shall make the final determination as to the
existence and cause of any alleged defect. No warranty is made with respect to custom equipment or products
produced to the Buyer’s specifications except as specifically stated in writing by the Seller in the contract for
such custom equipment.
This warranty is the only warranty made by the Seller with respect to the goods delivered hereunder, and may
be modified or amended only by a written instrument signed by a duly authorized officer of the Seller and
accepted by the Buyer.
Warranty and remedies on products not manufactured by the Seller are in accordance with warranty of the
respective manufacturer. THE SELLER MAKES NO OTHER WARRANTY OF ANY KIND WHATSOEVER,
EXPRESSED OR IMPLIED; AND ALL IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PUR-
POSE WHICH EXCEEDS THE AFORESAID OBLIGATIONS IS HEREBY DISCLAIMED BY THE SELLER.
INCASE OF DIFFICULTY
If you experience difficulty with this equipment, check the following, as appropriate:
1. Switch settings
2. Signal levels
3. Software configuration
4. Connections between Dantel’s equipment and your equipment.
If there is still a problem, substitute equipment that is known to be good. For additional assistance, call
Dantel’s Technical Field Service Department weekdays, 6 A.M. to 5 P.M. pacific time:
1-800-4DANTEL(1-800-432-6835).
If a thorough checkout shows a piece of equipment has malfunctioned, you may return it to the factory. For
repairs and emergency replacements, obtain a Return Material Authorization (RMA) number from the Cus-
tomer Service Representative at 1-800-4DANTEL (1-800-432-6835).
To ensure expedient processing of your order, provide a purchase order number and shipping and billing
information when requesting an RMA number. Also, when the units are returned to Dantel, include a descrip-
tion of the failure symptoms for each unit returned. Send defective equipment to:
Dantel, Inc. • 2991 North Argyle Avenue • Fresno, California 93727-1388
P.O. Box 55013 • Fresno, CA 93747-5013 Phone [phone] Fax [phone] http://www.dantel.com
WARRANTY