Se-Kure Controls SK-800KME Series User manual

Installation Instructions for the
ME Jr. plus 2 Alarm System SK-800KME Series
SK-3690
(Optional) “Where it’s At Light”
SK-807ME
ME Jr. plus 2 (8) Port Splitter Box
SK-80108ME
ME Jr. plus 2 (8) Port Strip
SK-809
Telephone Modular
“End Plug”
SK-800KME
ME Jr. plus 2 Alarm Module
Battery Installation:
1. Remove the screw that restricts the battery
door from opening using a phillips head
screwdriver as shown in Fig. 1.
2. Insert the key and turn it to the disarmed
position (the key cannot be removed in the
disarmed position).
Note: The battery door will not open without the
key in the lock and in the disarmed position.
3 .Remove the battery door.
4 .Before installing batteries, plug the (SK-195)
AC/DC Power Supply into the Alarm Module
jack marked Pwr. Input as shown in Fig. 2.
5 .Install (4) fresh “C” Cell Alkaline batteries
following (+) and (-) polarity shown in Fig. 3.
VERY IMPORTANT! When installing batteries,
always follow the polarity indicated on the
battery holder.
6 .Close the door as shown in Fig. 4. The horn
will “Double Chirp” until the door is securely
closed.
7 .Replace the battery door retaining screw as
shown in Fig. 5. (If the key is in the disarmed
position for 1-1/2 minutes, the horn will
“Single Chirp” every 15 seconds to indicate
that the unit is in the disarmed mode.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
SK-847-x
Extension
Connects
Alarm Module
to Splitters &
Strips &
Splitters to
Splitters
ME Jr. Terminals

AC Power Light
Will be lit when the SK-195 AC/DC
Power Supply is supplying power to
the Alarm Center.
Low Battery Light
Will )))flash((( when batteries
should be replaced.
Will )))flash((( if no batteries are
installed and the AC power is on.
Key Disarm Light
Will be lit when the Alarm Center is
Disarmed using the Key-Lock.
Keypad Disarm Light
Will be lit when the Alarm Center is
Disarmed using the Key-Lock.
Circuit “A” Light &
Circuit “B” Light
Will be lit if a Termination
“End Plug” is not installed.
Will )))flash((( if an alarm has
been caused on that circuit.
Will not be lit when all
sensors and the Termination
“End Plug” have been
properly installed.
Keypad Program Light
Will be lit when the Alarm
Center is in the keypad
programming mode and
ready to accept a new code.
2.
Installation:
The ME Jr. plus 2 Control Module has (2) circuits; one marked Circuit “A” and one marked
Circuit “B”. Any combination of up to (10) Splitters/Strips can be Daisy-Chained to the
Control Module as long as the total number from both circuits Does Not Exceed (10). If all
(10) Splitters/Strips are chained to a single circuit, an “End Plug” must be installed in the
other circuit. An “End Plug” must also be installed in the last splitter of each chain.
Special Note: Place the ME Jr. plus 2 in the Key Disarm Mode to install splitters and sen-
sors. The Key Disarm Mode prevents the unit from Automatically Arming after (4) minutes.
• After arranging display, connect Splitters/Strips together using the 6 ft.
(SK-847) cables (provided with each splitter).
If specific lenth cables is required: you may order them using Part No.
(SK-847-x), where x = the length of the cable in feet.
• Connect an ME Jr. Sensor to a port on the Splitter/Strip and to the corresponding display product.
Selecting Sensors for Display Product: (Sensors are available in Straight (P/LE) & Coiled (PC/LE).
SK-809
Telephone Modular “End Plug”
SK-847-x (x = Cable Length in Feet)
Extension (Connects Alarm Module
to Splitters & Splitters to Splitters)
SK-902
1" x 1" Bug Sensor SK-943 Tie Sensor SK-961 Ant Sensor Other Straight,
Coiled &
Dual Sensors
Are
Available.
Ask Your
Customer Service
Representative
For Details.
SK-904
1" x 2" Rectangular
Sensor
SK-927
Parallel Port Sensor
SK-953
collar Lasso Sensor
SK-955
Slim-Line Sensor
SK-968
Mini Phone Sensor
SK-990
Bendable Label
Sensor
)))
SK-HORN
Remote Horn
SK-800KME
ME Jr. plus 2 Alarm Module
SK-80108ME
8 Port KE Strip
SK-807ME
8 Large Port KE Splitter Box
SK-195
AC/DC Power Supply

3.
The “Where It’s At” LED Light:
All ME Jr. Splitter Boxes and Strips are
equipped with a “Where It’s At” light jack, for
this optional accessory. When an alarm occurs,
the light will )))flash((( to alert associates of the
location of the alarm. Plug them in wherever
needed, and adhere the
light where it can be seen
from a distance, (usually
at the top of a display).
Keypad Instructions:
Features:
A Keypad System has been added along
with the mechanical key system to provide
dual control.
Entering your access code or turning the key
will arm or disarm the alarm module.
The Yellow “Keypad Program” LED Light
above the keypad indicates when the
device is in the “Program Mode” and able
to accept new access codes from the user.
During an alarm, the horn will )))sound(((; at
this time, you can either (1) enter your
security access code on the keypad, or (2)
turn the key to place the system in the Dis-
Armed Mode.
The Keypad System features a device
called Auto-Arm. It is intended to automatic-
ally arm the system after (4) minutes.
Operation of the Keypad System:
When power is first applied to the device, it
will use the factory default code of : 1, 2, 3,
4. The user should change this code as
soon as possible. The system will accept the
default code until a new one has been
entered.
Always enter the [*]key before entering the
access code .
1. PRESS [#]
2. ENTER the current (4) digit
Security Code:
[_____] + [_____] + [_____] + [_____]
3. PRESS [*]
(After Step 3, the Yellow LED Keypad
Program Light will be ON).
4. ENTER the new (4) digit Security Code:
[_____] + [_____] + [_____] + [_____]
5. PRESS [*] (One More Time) then
PRESS [#] (To Store the New Code)
Note: The steps to change the Access Code
must be done within (8) eight seconds, or the
keypad will be reset to the last stored securi-
ty code, and you will be required to repeat
the steps.
Changing the Default Access Code:
Follow the steps below to change the access
code as desired. The codes cannot contain
the [*]star or the [#]pound symbol keys!
The system must be in the “Dis-Armed”
Mode before changing the code.

Se-Kure Controls,®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-[phone] • [phone] • Fax: [phone]
Rev. 7/22/02 SCI-9642©2002 Se-Kure Controls,®Inc.
On the Web: www.se-kure.com
E-Mail: [email protected]
SK-800KME
ME Jr. plus 2 Alarm Module
with Key Switch & Keypad
SK-800ME
ME Jr. plus 2 Alarm Module
with Key Switch Only
SK-800MEI
ME Jr. plus 2 Alarm Module
with Key Switch & Infrared Remote
Dip Switches
Fig. 6
4.
Fig. 7
Dip Switches Battery
SK-882 - Infrared
Remote Transmitter
Setting Up The Infrared
Remote:
1. Open the battery compartment door to reveal the dip switches on
the side of the SK-800MEIAlarm Module, as shown in Fig. 6.
2. Unscrew and open the SK-882 Infrared Remote. It is fastened
together with a small phillips head screw, shown in Fig. 7.
3. Arrange the Dip Switches into any configuration to create your
own encoded signal. Make sure the Dip Switches match on the
Alarm Module and the Infrared Remote Transmitter.
Note: It is highly recommended that you change the Dip Switch
settings from the factory default. This protects the system from being
tampered by anyone with an infrared remote set on the factory
default.
4. Close the Alarm Module and the Infrared Remote Transmitter.