Communication
USB Communication
The DL-Axist single Ethernet dock supports USB 2.0 high speed
interface. Use a standard USB (type A to B) cable to connect the
dock to a host device and transfer data.
1. Connect power to the dock.
2. Plug the USB cable into the USB port on the back of the
dock.
3. Connect the other end of the USB cable to the USB port of
the host device.
4. Slide the Ethernet/USB switch to the USB position
5. Insert the DL-Axist into the dock.
Ethernet Communication
The DL-Axist single Ethernet dock supports Ethernet interface.
Use a standard UTP CAT 5E cable to connect the dock to an
Ethernet hub and transfer data.
1. Connect power to the dock. Use country specific power
cord. Refer to the Datalogic website.
2. Plug the UTP CAT 5E into the Ethernet port on the back of
the dock.
3. Connect the other end of the UTP CAT 5E cable to the
Ethernet hub.
4. Slide the ethernet/USB switch to the Ethernet position
5. Insert the DL-Axist into the dock.
Technical Specifications
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Power
Cord
Power Supply
Host PC DL-Axist
A to B USB
cable Single
Ethernet Dock
Power
Cord Power Supply
Ethernet Hub
DL-Axist
UTP CAT 5E
cable Single
Ethernet Dock
WARNING
Do not use the cradle in a PoE network, i.e. in a
network with PSE able to supply power: there is the
risk to compromise, in irreversible way, the
functionality of the cradle.
Electrical Features
Consumption1
1. Use only DL approved power adapters.
2.2 - 2.3 A
Indicators
Power on LED (green)
Spare battery charge LED (bicolored)
Ethernet LEDs
Charge Time Standard battery: 4 hours; extended battery:
8 hours
Communication Features
Interface USB 2.0; Ethernet
Baud Rate 480 Mbps for USB 2.0; 10 Mps for Ethernet
Environmental Features
Working
Temperature2
2. Spare batteries should be charged at an ambient temperature
between 0 - 35º C to achieve the maximum charging rate.
Charging is allowed in the battery temperature range 0-45°C.
Never charge the main device or spare batteries in a closed
space (cabinet) where excessive heat can build up.
-20°C to 50°C (-4°F to 122°F)
Storage
Temperature -30°C to 70°C (-22°F to 158°F)
Humidity 90%
Mechanical Features
Dimensions 126 x 134 x 62 mm / 4.96 x 5.28 x 2.44 in
Weight about 405 g / 14 oz
©2016-2018 Datalogic S.p.A. and/or its affiliates • All rights reserved. •
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. DL-Axist is a
trademark of Datalogic S.p.A. and/or its affiliates. All other trademarks
and brands are property of their respective owners.
www.datalogic.com
