Datalogic Single Ethernet Cradle Memor User manual

Datalogic Memor™ Single Ethernet Cradle
NOTE
Read this manual carefully before performing any type
of connection through the Datalogic Memor™ Single
Ethernet Cradle.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
NOTE
Do not attempt to disassemble the Datalogic Memor™
Single Ethernet Cradle, as it does not contain parts that
can be repaired by the user. Any tampering will invalidate
the warranty.
The Datalogic Memor™ Single Ethernet Cradle paired with one Datalogic
Memor™ mobile computer builds a reading system for the collection,
decoding and transmission of barcoded data.
The communication between the mobile computer and host PC through
the Datalogic Memor™ Single Ethernet Cradle may occur also by using
the standard ActiveSync® connection.
Figure 1 – Datalogic Memor™ Single Ethernet Cradle
A) LED Indicators
B) Spare Battery Slot
C) Mini USB Connector
D) RS232 Connector
E) Power Jack
F) Ethernet Port with LED indicators
G) Switch Ethernet/USB
The Datalogic Memor™ Single Ethernet Cradle is a serial
communication adapter between the host computer and the Datalogic
Memor™ mobile computer. Power supply is required to be connected to
the Cradle only for ethernet communication.
Since the Datalogic Memor™ Single Ethernet Cradle also functions as a
battery charger, a power supply is required for battery recharging
operations, both for the mobile computer and spare battery pack
recharging. The spare battery pack recharging slot can supply a 1000
mAh as well as a 2000 mAh Battery pac.
822000820
By inserting the Datalogic Memor™ into the cradle, data can be
transmitted to the host and its battery begins charging if the power supply
is connected. In addition, a spare battery can be charged by inserting it
into the slot at the back of the Datalogic Memor™ Single Ethernet Cradle
as shown in the following figure.
Figure 2 – Datalogic Memor™ Single Ethernet Cradle Charging and
Communication
The LEDs positioned on the front part of the Datalogic Memor™
Ethernet Cradle (see figure below) indicate the cradle and spare
battery charger status:
Figure 3 - LED Indicators
Front LED indicators
LED STATUS
Red Constant Spare battery charging*
Charger Green Constant Spare battery charge
completed
Power Green it is constant when the
cradle is powered
* During charging, the LED may turn off to indicate a temporary
suspension of charging.
Ethernet Connector LED Indicators
Solid Green Link established
Flashing Green Link activity
Ethernet
Green LED
(left) Off No link established
Off 10 Mb connection
Ethernet
Yellow LED
(right) Solid Yellow 100 Mb connection (this model is not
available)
CONNECTIONS
CAUTION
Connections should always be made with power OFF!
USB CONNECTION
The Datalogic Memor™ Single Ethernet Cradle can be connected to the
host by means of any standard Mini USB cable.
Once the host has been turned on, insert the Datalogic Memor™
mobile computer into the cradle.
Figure 4 - USB Connection
A) Host Computer C) Datalogic Memor™ Single
Ethernet Cradle
B) Std Mini USB (i.e.
94A051016 CAB-421) D) *Power Supply (only necessary for battery charging)
* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
NOTE
Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.
Spare battery
Charge Slot with
Spare Battery
Inserted
Data Transmission and
Mobile Computer Battery
Charging
Spare Battery
Charger LED
Power LED
A
BC
D*
A
B
C
D
F G
E

RS232 CONNECTION
The Datalogic Memor™ Single Ethernet Cradle can be connected to the
host by means of any standard null modem cable. The 9-pin female D-
Sub connector must be connected to the RS232 port of the cradle.
Once the host has been turned on, insert the Datalogic Memor™
mobile computer into the cradle.
Figure 5 - RS232 Connection
A) Host Computer C) Datalogic Memor™ Single
Ethernet Cradle
B) Null Modem cable D) *Power Supply (only necessary
for battery charging)
* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
NOTE
Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.
ETHERNET CONNECTION
Connect the Ethernet cradle (Ethernet port ) to an Ethernet hub or a port on
the host device. Connect the Power jack to a power supply*.
Figure 6 - Ethernet Connection
A) Datalogic Memor™
Single Ethernet Cradle C) UTP CAT 5E cable (recommended use)
B) Ethernet hub D) *Power supply
* Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
NOTE
Be sure that the switch is in the “Ethernet” position
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the cradle.
NOTE
You may need to set the cradle configuration or the
terminal behaviour using respectively the "Cradle
Manager" Windows XP application and the
"CPCradleCE" Windows CE application. You can
download the "Cradle Manager" installation file and the
full "Datalogic Memor™Single Cradle User Guide" from
the Datalogic Mobile website:
www.mobile.datalogic.com.
TECHNICAL FEATURES
Datalogic Memor™ Single Ethernet Cradle
Electrical Features
Power Supply* 5 VDC ± 5%
Consumption Max. 2.5 A
Indicators Power on LED (green)
Spare battery charge LED (bi-colored)
Ethernet LEDs (green and yellow)
Charge Time 1000 mAh Battery: max. 3 hours
2000 mAh Battery: max. 6 hours with terminal
inserted, max. 4.5 hours without terminal
Communication Features
Interface RS232, USB 1.1 version, Ethernet
Baud Rate RS232 = up to 115200 b/sec; USB = up to 12
Mb/sec; Ethernet = up to 10 Mbps
Environmental Features
Working Temperature** 0° to +50 °C (+32° to +122 °F)
Storage Temperature -20° to +65 °C (-4° to +149 °F)
Humidity 80% non condensing
Degree of Protection IP50
Mechanical Features
Dimensions 105 X 75 X 102 mm (4.13 X 2.95 X 4.02 in)
Weight 340 g (12 oz)
*Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
** Battery must be charged at a temperature ranging from 0° to +45
°C (+32° to +113 °F).
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed
written approval of Datalogic could void the authority to use the
equipment.
This device complies with PART 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Datalogic Mobile S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara
Bologna - Italy 07
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DL-Memor Single Ethernet Cradle
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla
sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product
safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité
des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit
und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad
electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022 ( CLASS B ITE ), SEPTEMBER 1998:
INFORMATION TECHNOLOGY EQUIPMENT
RADIO DISTURBANCE CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENTS
EN 55024, SEPTEMBER 1998:INFORMATION TECHNOLOGY EQUIPMENT
EN 55024/A1, OCTOBER 2001: IMMUNITY CHARACTERISTICS
EN 55024/A2, J
A
NUARY 2003: LIMITS AND METHODS OF MEASUREMENTS
Lippo di Calderara, March 9th, 2007
Paola Chientaroli
Quality Assurance Manager
A
B C
D*
D
A
C
B