Datalogic Lynx D User manual

LynxTM Single Slot Dock
Quick Start Guide
The Single Slot Dock paired with a Lynx PDA builds a reading system
for the collection, decoding and transmission of barcoded data.
The Single Slot Dock is both a USB and a serial communication
adapter between the terminal and the host computer.
The Single Slot Dock also functions as a battery charger, both for the
terminal and the spare battery pack (standard 94ACC0064 and high
capacity 94ACC0065). The spare battery can be charged by inserting it
into the slot at the back of the cradle.
Power supply is required for the Lynx to be connected to the cradle
and for battery recharging operations.
General View
PDA Insertion/Removal
For correct insertion into the dock, insert the PDA from the top of the
dock and push it down.
To remove the PDA from the dock, simply pull it upwards while
holding the dock firmly down.
Power Supply
Each dock requires a power supply.
LED Indicators
Using the Spare Battery Charger
Insert the battery pack, contacts side first, into the slot and press it
until the battery latch is automatically closed; charging starts
automatically.
To remove the battery, press the battery-release lever.
Fastening the Dock to a Surface
To securely fasten the Single Slot Dock to tables, desks and other
surfaces, and to prevent the dock from moving when you remove the
device, use the four velcro dual lock feet provided with the matching
dual-lock adhesive pads.
Remove the protective feet from the dock before attaching the velcro
dual lock feet.
NOTE
Read this manual carefully before performing any type of
connection from the terminal to a host PC using the Single
Slot Dock.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
NOTE
Do not attempt to disassemble the Single Slot Dock, as it
does not contain parts that can be repaired by the user.
Any tampering will invalidate the warranty.
Power On
LED RS232 Connector
Power
Jack
Spare Battery Slot
Battery Charge
Status LED
Contacts for Lynx
USB Connector
LED Status
Power ON LED
Solid green Dock is powered.
Battery Charge Status LED
Off Battery absent.
Solid red Battery charge in progress.
Solid green Charge completed.
Blinking red Error.
-
+
822001283 (Rev. A) Jan. 2018
©2015-2018 Datalogic S.p.A. and/or its affiliates • ALL RIGHTS RESERVED.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in
many countries, including the U.S.A. and the E.U. Lynx is a trademark of
Datalogic S.p.A. and/or its affiliates, registered in many countries, including the
U.S. and the E.U. All other trademarks and brands are property of their
respective owners.

Connections
USB Client Connection
Connect the Single Slot Dock to the host by means of a Micro-B USB
cord, such as Datalogic 94A051968 cable.
Once the host has been turned on, insert the Lynx into the dock.
A. Host computer
B. 94A051968 Micro-B to Std-A USB straight cable
C. 94A150036 Lynx Single Slot Dock
D. Power Adapter
Connection to USB Peripherals
Connect the Single Slot Dock to the peripheral by means of a Micro-A
USB cord, or use a Micro-A to Std-A receptacle USB adapter such as
Datalogic 94A051969 (together with a standard USB cable if needed).
A. USB Peripheral (memory)
B. Standard A to Micro A USB Cable
C. 94A051969 Micro-A to Std-A receptacle USB adapter
D. 94A150036 Lynx Single Slot Dock
E. Power Adapter
RS232 Connection
Connect the Single Slot Dock to the host by means of a standard null
modem cable such as Datalogic 94A051020 CAB-427 for 9-pin
connections.
Once the host has been turned on, insert the Lynx into the dock.
A. Host computer
B. 94A051020 9-pin serial cable
C. 94A150036 Lynx Single Slot Dock
D. Power Adapter
Communication Module Extensions
To install a communication module, remove the label covering the
communication module connector on the bottom of the dock, as
shown in the figure below:
The communication modules available are the following:
• 94ACC1371 Single Slot Dock Ethernet Module
• 94ACC1372 Single Slot Dock Modem Module.
Technical Specifications
FCC Compliance
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Modifications or changes to this equipment without the expressed
written approval of Datalogic could void the authority to use the
equipment. This device complies with PART 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference which may cause
undesired operation.
D
A
B
C
C
E
AB
D
WARNING
Do not use the cradle in a PoE network, i.e. in a
network with PSE able to supply power: there is the
risk to compromise, in irreversible way, the
functionality of the Ethernet Module.
D
A
B
C
Electrical Features
Power supply1
1. This device is intended to be connected to a UL Listed/CSA Certified Power
Unit marked “Class 2” or LPS power source rated 5 V, 3A. The package may
include international plug adapters. The adapters must be plugged in the
power supply before the power supply itself is plugged on the wall outlet.
5 VDC ± 5% @ 3A
Consumption Max 3 A with PDA inserted
Spare slot charge time
Std Battery 3h
High Cap Battery 4h 30
Communication Features
Interface RS232, USB 1.1 version
Baud Rate RS232 = 9600 - 115200
Environmental Features
Working Temperature2
2. When inserted in the spare slot, batteries must be charged at a tempera-
ture ranging from 0° to 44°C. Never charge the main device or spare bat-
teries in a closed space where excessive heat can build up.
0° to +50°C / 32° to 122°F
Storage Temperature -20° to +70°C / -4° to 158°F
Humidity 95% without condensation
Electrostatic discharge
EN 61000-4-2 4 KV contact / 8 KV air
Physical Features
Dimensions 110 x 140 x 72 mm / 4.3 x 5.5 x 2.8 in
Weight (without cables) 185 g / 6.5 oz
Indicators Green power-on LED
Bicolored battery charge status LED