Datalogic Memor 1 User manual

Memor™ 1
3-Slot Cradle
Installation Guide

Datalogic S.r.l.
Via San Vitalino 13
40012 Calderara di Reno (BO)
Italy
Tel. [phone]
Fax [phone]
©2019 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of
this documentation may be reproduced, stored in or introduced into a retrieval
system, or transmitted in any form or by any means, or for any purpose,
without the express written permission of Datalogic S.p.A. and/or its
affiliates. Owners of Datalogic products are hereby granted a non-exclusive,
revocable license to reproduce and transmit this documentation for the
purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions
of the documentation. Should future revisions of this manual be published,
you can acquire printed versions by contacting your Datalogic representative.
Electronic versions may either be downloadable from the Datalogic website
(www.datalogic.com) or provided on appropriate media. If you visit our
website and would like to make comments or suggestions about this or other
Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this
manual that is complete and accurate, however, Datalogic reserves the right
to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A.
in many countries, including the U.S.A. and the E.U. Memor is a trademarksof
Datalogic S.p.A. and/or its affiliates. All other brand and product names may
be trademarks of their respective owners.
Patents
Patent. See www.patents.datalogic.com for patent list.

Installation Guide i
Table of Contents
Introduction ....................................................................... 1
Dispenser Design Guidelines ........................................... 3
Functional Areas ..........................................................................3
Base Unit Configuration ..............................................................5
Configuration J0 ............................................................................... 7
Configuration J1 ............................................................................... 8
Configuration J2 ............................................................................... 9
Configuration J3 ............................................................................. 10
Configuration J4 ............................................................................. 11
Configuration J5 ............................................................................. 12
Configuration J6 ............................................................................. 13
Configuration J7 ............................................................................. 14
Configuration J8 ............................................................................. 15
Configuration J9 ............................................................................. 16
Configuration J10 ........................................................................... 17
Configuration J11 ........................................................................... 18
Base Unit Configurations Summarizing Table ........................... 18
Ventilation Grilles Position ........................................................... 20
Shopper Unit Placing and Unity Definition ................................. 21
Dispenser Construction Details.................................... 23
Base Unit Description ............................................................... 23
Memor 1 3-Slot Cradle Installation ............................................. 23
Remove the Memor 1 from the 3-Slot Cradle ............................ 28
Base Unit Construction Details - Pattern Holes ........................ 29
Anchoring and Maintenance Issues ............................................ 38
Protection Against Cart/Trolley Impacts .................................... 38
Power Supply ............................................................................. 39

ii Memor™ 1 3-Slot Cradle
Powering the Cradle ...................................................................... 41
LED Indicators ..................................................................................45
Radio Technologies and Frequency Bands .............................47
Technical Specifications ............................................................48
Maintenance ...............................................................................50
Cleaning .......................................................................................... 50
Safety Precautions .....................................................................51
Cabinet ............................................................................................ 51

Installation Guide 1
Introduction
The purpose of this document is to provide helpful instructions
about designing and building a cabinet to house the Memor 1 3-Slot
Cradles. The first part of the document gives information useful to
build the best dispenser layout, according to the retail environment
needs. In this section you can find some indications coming from
Datalogic direct experience in different kinds of retail environments.
The layout indications are suggestions to help design a functional
cabinet.
The second part of the document gives some technical details
needed to build a vertical dispenser. Drawings and descriptions in
this section are provided as indications about constraints that must
be followed to properly install the cradles into the cabinet and not as
comprehensive and detailed rules to build up the cabinet itself. The
drawings and the pictures in this document apply to a wood cabinet.
It is however possible, using the same indications, to use a different
material.

Introduction
2 Memor™ 1 3-Slot Cradle
NOTES

Installation Guide 3
Dispenser Design Guidelines
Functional Areas
The Memor 1 is also suitable for an effective communication inside
the retail environment, thanks to the high quality of its display. For
this reason, it is important to design the arrangement of the device
in a dispenser to bring out the performances without compromising
the functionality. The following drawing shows the most profitable
way to place the devices following their height from the floor.
• The devices placed in the higher part of the dispenser –
between 1m and 1.60m – perform their communicative
function in the most profitable way. So, in this area, it is
preferable to maximize the display visibility, even if this means
to fit a smaller quantity of devices. ·
• The devices lodged in the lower part of the dispenser – below 1
m. of height – do not offer a clear display visibility and cannot
fully exploit their own communicative potential, therefore this
area is suitable to maximize the devices density.

Dispenser Design Guidelines
4 Memor™ 1 3-Slot Cradle

Dispenser Design Guidelines
Installation Guide 5
Base Unit Configuration
The preceding paragraphs provided some general rules on building a
base unit, taking into account the space required for the cabinet, the
density and the display visibility. Every retail environment has
different and specific needs and constraints: some may need a tall
base (but not deep or large), some may need a short base but can
accept larger and bulkier sizes.
There are basically two different solutions organizing the
disposition of the devices:
• High Visibility Configuration
• High Density Configuration
In field, however, practical solutions mix up vertical and diagonal
layout in different manner. The following paragraphs shows some
example solutions that you can refer to when designing your own
solution. A three columns base unit is used as a sample model.

Dispenser Design Guidelines
6 Memor™ 1 3-Slot Cradle
NOTE
To guarantee full stability, the cabinet must be anchored to
the wall or to the floor. (see Anchoring and Maintenance
Issues on page 38)
The front door dispenser must have a jamb of 20 cm, to
allow the front door to open.